Shear force in bolted connections for hybrid steel-FRP bridges

Shear force in bolted connections for hybrid steel-FRP bridges: Due to traffic, temperature and fatigue loading

Gribnau, Koen (TU Delft Civil Engineering and Geosciences)

Pavlovic, M. (graduation committee)
de Boon, J. (graduation committee)
Ravenshorst, G.J.P. (graduation committee)
Christoforidou, A. (graduation committee)

Delft University of Technology

2021-06-17

Fibre reinforced polymers (FRP) can be a solution for future bridge renovation when only the deck of the bridge needs replacement. In these cases the deck is replaced with an FRP sandwich panel deck. The main advantages are a high strength-to-weight ratio which is beneficial for the ever heavier lorries and the fast installation which prevents hindrance. To connect the FRP deck with the steel superstructure, bolted connectors are used. One of the aspects that needs to be investigated before the bolted connectors can be applied are the relevant loads on the bolted connectors. The focus of this thesis will be to investigate the relevant static and fatigue forces on the connectors.
55 existing girder and arch bridges have been selected from a database of Rijkswaterstaat. For each bridge an appropriate FRP deck has been designed with an analytical method. The bridges are modelled in SOFiSTiK to investigate the shear forces in the connectors. The layout of the bolted connectors is kept constant for all bridges, as well as the transverse stiffness of the connector. The shear forces are calculated with a linear analysis. Before the static and fatigue analyses, first the hybrid interaction of the model is investigated. The hybrid interaction is the amount of horizontal forces transferred between the FRP deck and the steel super-structure. Hybrid interaction is beneficial as it increases the strength of the structure. Two models of a generic bridge have been investigated, the first is the standard model which is supposed to use hybrid interaction. The second model is an adjusted version to create a non-hybrid model. Three parameters are investigated: the deflection, the slip and the longitudinal stress over the height of the beam. The results show that hybrid interaction is created with the bolted connectors in the standard model.
In the static analyses two loads are investigated: traffic loads and temperature loads. The shear forces in the longitudinal direction are investigated as this is the governing direction. Before the loads are applied on the existing bridges, first a generic bridge has been investigated to gain knowledge over three bridge parameters. First the facing laminate of the FRP deck is changed. Second the direction of the webs of the FRP deck, and this also changes the connector layout due to feasibility. Third the expansion coefficient of the resin is changed. For traffic loads mainly the direction of the webs influences the shear forces in the connectors. For temperature loading the shear forces are largely depending on the expansion coefficient of the laminate, the close the expansion coefficient to the expansion coefficient to the steel superstructure, the lower the shear forces. The existing bridges that have been investigated resulted in a large scatter in results. The layout of the superstructure of the bridge influences the facing laminate and the number of connectors, which influences the maximum shear forces in the connectors. For both traffic and temperature loads, the connectors close to the supports experience the highest shear forces.
Besides the static loading, also fatigue is investigated. The shear forces in the connectors are calculated for one bridge, namely the approach bridge Nieuw Vossemeer. This bridge is one of the heaviest loaded bridges in the static analyses and it is according to expect judgement facing deck problems. Two aspects are investigated in the fatigue analysis, first the magnitude and second the type of load cycles. The magnitude is important as this needs to be below the slip resistance of the bolted connectors. The type of load cycles is important as this is related to how damaging the load cycle is. Because there are no S-N curves for bolted connectors between an FRP deck with a steel superstructure, the damage cannot be calculated. The R-ratio is used to investigate the type of load cycles. To calculate the R-ratio of a load cycle, the minimum shear force is divided by the maximum shear force. The resulting number expresses the type of load cycle. For the results, distinction has been made between the connectors close to the supports and connectors in the lengthwise middle of the bridge span. Both the magnitude as the type of loading is different.
Finally, it is concluded that the shear forces in the connectors is one of the aspects to be considered when designing a bridge with hybrid interaction between the FRP deck and steel superstructure. A large scatter of shear forces can be expected, depending on the bridge layout. Incorrect deck design can result in unnecessary high shear forces. The connector layout can be optimised to make the design more cost efficient.

FRP
Shear force
Bolted connection

http://resolver.tudelft.nl/uuid:a6250270-77b4-4ee3-9495-fc1aeac84813

Student theses

master thesis

© 2021 Koen Gribnau