- document
-
Steutel, P. (author)The majority of existing problems within conventional prosthetic fingers are related to the use of conventional rigid links and kinematic joints and to the lack of adaptability of the finger. In this paper these problems are solved by the design of a fully compliant under-actuated prosthetic finger. At first a basic structure was defined....master thesis 2010
- document
-
Schuddeboom, P.D. (author)The Finite Element Method is used in many computer programs to analyse the mechanical behaviour of shell structures. Although this method provides good quantitative insight into the mechanical behaviour of shell structures, it provides little qualitative insight. This master graduation thesis is aimed at expanding Finite Element Analysis (FEA)...master thesis 2014
- document
-
Van Velzen, B. (author)Atherosclerosis is a progressive arterial disease in which fatty tissue accumulates in the arterial wall. Due to this lipid uptake, the artery thickens and can eventually rupture, causing the lipids to flow into the bloodstream and form blood clots. If this happens in the carotid arteries, which supply the head with oxygenated blood, a stroke...master thesis 2015
- document
-
Heijmer, M.B.M. (author)An accurate corner strength modelling method is required at Fokker Aerostructures to design canisters (missile launch tubes) with rounded corners for an internal pressure load case. To this end a combination of experiments and calculation methods has been developed that enable to predict the corner strength more accurately. Internal pressure...master thesis 2016
- document
- Zwanenburg, A.M. (author) master thesis 2017
- document
-
Shroff, A. (author)Within 100 years of the Wright Brother's first flight, we are already approaching the top of aviation’s technological S-curve. Breakthrough technical improvements have resulted in an undeniable increase in efficiency and range, but today’s aircrafts are still relatively inefficient resulting in a large amount of air and noise pollution. In order...master thesis 2017
- document
-
Gámir Huguet, Carlos (author)A novel continuum damage mechanics model for 2D woven fabrics has been developed and implemented in a VUMAT subroutine for Abaqus/Explicit. The model takes into account the shear non-linearity, the toughening mechanisms associated to tensile failure, and the influence of shear stresses in the initiation and propagation of tensile damage. <br/>...master thesis 2017
- document
-
Xu, Quanxin (author)Throughout the history of pavement structure, the parallel layer structure has dominated the structural design of pavements. In other words, the entire road pavement share a uniform thickness design regardless how many lanes there are. However, due to traffic regulations and driving habits, the traffic flow most probably does not distribute...master thesis 2017
- document
-
Jayananda, Nikhil (author)Strain hardening cementitious composite is a new generation material with increased ductility and improved cracking behaviour as compared to traditionally used Normal Strength Concrete (NSC). An important charactersitic of SHCC is the ability of the fibers (2% PVA) in the composite mixture to bridge the cracks and there by preventing...student report 2017
- document
-
Berbers, Stijn (author)Seafox owns and operates a fleet of 12 Jack-ups. The design life of these Jack-ups is typically around 30 years. However, some have remained operational after exceeding their design life. It is therefore critical to gain an understanding how long and under what conditions these jacks-ups are still able to operate safely. There are two main...master thesis 2017
- document
-
Rahadian, Rheza (author)Watertightness and leakage prevention is crucial in every tunnel joint design. Immersed tunnels have been utilizing the Gina-Omega gasket solution since the 1960s to prevent leakage from occurring. However, after almost 50 years of service life, leakages were detected in the immersion joints, which leads to an investigation into the source of...master thesis 2017
- document
-
CHEN, Xin (author)Bridges with different geometrical configurations have been searched with linear finite element analysis. The aim is to find the position and value of critical proof load. Four different parameters, namely span length, width, skewness and thickness ratio, their influence on proof load are found. In total, 166 sets of data are obtained by...student report 2017
- document
-
Jacobs, Erwin (author)The search for a transparent, reversible, and reusable consolidation system for monuments led to the ambition to test possible cast glass interlocking brick designs using numerical calculations. The focus of this research is hence the design, simulation and evaluation of a possible cast glass interlocking geometry using Finite Element Analysis ...master thesis 2017
- document
-
Koeman, Jurrien (author)Delamination is one of the failure modes of composites prone to happen in the case of a car crash. In the early stages of car design, finite element analysis is used as a tool to analyze structural concepts. In order to model delamination in a newly developed material model, it is analyzed in two parts: detection and effects of delamination. To...master thesis 2017
- document
-
Hildering, Sven (author)This master thesis covers the research into cracking behaviour of slender high strength concrete cantilevering balconies. The research emerged from Pieters Bouwtechniek Delft and Hi-Con Denmark. They cooperatively designed very slender balconies in ultra-high performance fibre reinforced concrete. Other engineering firms tend to recreate these...master thesis 2018
- document
-
Buist, Declan (author), Salzmann, Elke (author)This thesis is about the simulation of the permanent magnet motors of the Nuna Solar Car in order to find their fundamental motor parameters. These parameters can then be used in a Field-Oriented control algorithm to be used in a new motorcontroller for the team. A finite element analysis is done on the two current motors of the Nuna solar car,...bachelor thesis 2018
- document
-
Wang, Jiayi (author)This graduation project is in cooperation with TU Delft, Tentech BV, Aectual and White Lioness technologies. It aims to investigate the feasibility of using recycled plastics as material for large-scale 3D printing with the 3D printer KamerMaker. In the meantime, a thickness distribution methodology is proposed for taking advantage of the...master thesis 2018
- document
-
Ferket, Max (author)This research investigates how the equivalent frame method in combination with a sequentially linear analysis can be used to model the behaviour of a façade of an unreinforced masonry structure, subjected to a lateral pushover load. The experimental data of the two-story building experiment at the University of Pavia is used.<br/>Two different...master thesis 2018
- document
-
Zhou, Peixuan (author)Automated tape or fiber placement (ATP/AFP) with in-situ consolidation has been identified as a promising manufacturing technique for thermoplastic (TP) composites, which are highly in-demand in the aerospace industry for future aircraft structural applications. This manufacturing technique is attractive since it has the potential to eliminate...master thesis 2018
- document
-
Swinnen, Jan (author)The use of fibre reinforced polymers (FRP) are stimulated in the construction industry for their remarkable corrosion resistance, good thermo-mechanical properties, high strength-to-weight ratio and high stiffness-to-weight ratio. The open-hole strength of FRP is an important parameter in a composite design because it can be representative in...bachelor thesis 2018