Surface Redox Pseudocapacitance of Partially Oxidized Titanium Carbide MXene in Water-in-Salt Electrolyte

Achieving pseudocapacitive intercalation in MXenes with neutral aqueous electrolytes and driving reversible redox reactions is scientifically appealing and practically useful. Here, we report that the partial oxidation of MXene intensifies pseudocapacitive Li+ intercalation into Ti3C2Tx MXene from neutral water-in-salt electrolytes. An in...

Simulation of foam enhanced-oil-recovery processes using operator-based linearization approach

Foam injection is a promising enhanced-oil-recovery (EOR) technology that significantly improves the sweep efficiency of gas injection. Simulation of foam/oil displacement in reservoirs is an expensive process for conventional simulation because of the strongly nonlinear physics, such as multiphase flow and transport with oil/foam...

Quantitative Modeling of the Effect of Oil on Foam for Enhanced Oil Recovery

The effectiveness of foam for mobility control in the presence of oil is key to foam enhanced oil recovery (EOR). A fundamental property of foam EOR is the existence of two steady-state flow regimes: the high-quality regime and the low-quality regime. Experimental studies have sought to understand the effect of oil on foam through its effect on...

Three-Phase Fractional-Flow Theory of Foam-Oil Displacement in Porous Media with Multiple Steady States

Understanding the interplay of foam and non-aqueous phases in porous media is key to improving the design of foam for enhanced oil recovery and remediation of aquifers and soils. A widely used implicit-texture foam model predicts phenomena analogous to cusp catastrophe theory: the surface describing foam apparent viscosity as a function of...

New Capillary Number Definition for Micromodels: The Impact of Pore Microstructure

A new capillary number (N _ca ) definition is proposed for 2-D etched micromodels. We derive the new definition from a force balance on a nonwetting ganglion trapped by capillarity. It incorporates the impact of pore microstructure on mobilization. The geometrical factors introduced can be estimated directly from image analysis of...

Experimental Investigation of the Effect of Oil on Steady-State Foam Flow in Porous Media

Foam flow in porous media without oil shows two regimes depending on foam quality (gas fractional flow). Complexity and limited data on foam/oil interactions in porous media greatly restrict understanding of foam in contact with oil. Distinguishing which regimes are affected by oil is key to modeling the effect of oil on foam. We report...

CT coreflood study of foam flow for enhanced oil recovery: The effect of oil type and saturation

We present a CT coreflood study of foam, both pre-generated and generated in-situ, displacing oil, as a function of oil type and saturation. Foam generation and propagation are reflected through sectional pressure measurements. Dual-energy CT imaging monitors in-time phase saturations. With an oil less harmful to foam (hexadecane), injection...

Experimental investigation on the effect of the duct geometrical parameters on the performance of a ducted wind turbine

This paper reports an experimental investigation on the effect of the duct geometry on the aerodynamic performance of an aerofoil shaped ducted wind turbine (DWT). The tested two-dimensional model is composed of an aerofoil equipped with pressure taps and a uniform porous screen. The experimental setup is based on the assumption that the duct...

Experimental Study Of Flow Field Of An Aerofoil Shaped Diffuser With A Porous Screen Simulating The Rotor

This study presents an experimental investigation on a diffuser augmented wind turbine (DAWT). A screen mesh is used to simulate the energy extraction mechanisms of a wind turbine in experiment. Different screen porosities corresponding to different turbine loading coefficients are tested. Measurements of the axial force and of the velocity...

A novel capsule-based selfrecovery system with a chloride ion trigger

Steel is prone to corrosion induced by chloride ions, which is a serious threat to reinforced concrete structures, especially in marine environments. In this work, we report a novel capsule-based selfrecovery system that utilizes chloride ions as a trigger. These capsules, which are functionalized via a smart response to chloride ions, are...

Stability criterion and its calculation for sail-assisted ship

Fast Etching of Molding Compound by an Ar/O2/CF4 Plasma and Process Improvements for Semiconductor Package Decapsulation

Decapsulation of a SOT23 semiconductor package with 23 um copper wire bonds is conducted with an especially designed microwave induced plasma system. It is found that a 30%-60% CF4 addition in the O2/CF4 etchant gas results in high molding compound etching rate. Si3N4 overetching which is encountered in plasma decapsulation is solved by an...

Plasma Etching for Failure Analysis of Integrated Circuit Packages

Plastic integrated circuit packages with copper wire bonds are decapsulated by a Microwave Induced Plasma system. Improvements on microwave coupling of the system are achieved by frequency tuning and antenna modification. Plasmas with a mixture of O2 and CF4 showed a high etching rate around 2 mm3/min. The role of O2 and CF4 in etching molding...