Searched for: department:"Hydraulic"
(1 - 20 of 42)

Pages

document
Le, T.N. (author)
Prototype single layer armour units on a breakwater slope are observed to break. To predict when breakage occurs, the objective of this research project is to obtain knowledge on, and measurements of the rocking behaviour and failure mode of single layer armour units. A single cube on a breakwater slope is subjected to investigations. An...
master thesis 2016
document
Hellinga, L.B. (author)
Breakwaters with single layer concrete armour are very commonly applied nowadays. Much research is available on the stability of single layer armour units on the seaward slope. However, rear slopes design methods for single layer armour units are rare. On rear side slopes usually similar sized units as on the seaward slope are applied. Limited...
master thesis 2016
document
Azikci, M.A. (author)
The Van der Meer formula for amour stability takes the Iribarren number, number of waves and damage level into account. It also contains a factor P which describes the “notional permeability” of the breakwater. This factor is based on the fact that a more permeable structure dissipates more energy and hence requires less heavy armouring. Its...
master thesis 2015
document
Broere, A. (author)
The protection of breakwater structures is in this research considered. The design of rubble mound concrete armour layers for breakwaters can be divided in a single layer system and a double layer system. The single layer system is nowadays mostly applied because of the high interlocking, high stability of the structure, reduction of concrete...
master thesis 2015
document
Verpoorten, S.P.K. (author)
Seaports are often protected against waves and currents by rubble mound breakwaters. At the interface between outer breakwater slope and seabed a toe structure is often build, which provides stability to the outer slope. The toe consists of a relatively small heap of rock. Since 1977 dedicated studies are made to the stability of these rock...
master thesis 2015
document
Piccoli, C. (author)
This report presents the results of an Additional MSc Thesis as part of the Master Programme of Hydraulic Engineering from the Delft University of Technology Civil Engineering and Geosciences Faculty. The objective of this additional graduation work is to provide a better insight on economical optimization of breakwaters. Information about the...
master thesis 2014
document
Verdegaal, I. (author)
The permeability of a breakwater is of great importance for the stability of the armour layer. The influence of the structural permeability on the stability of rock armour units was already researched by Van der Meer using the 'notional' permeabiltiy. However, for single layer interlocking armour units the influence core permeability is rather...
master thesis 2013
document
Disco, M.J. (author)
Breakwaters are used for reducing wave height in harbours or divert sediment. One of the types of breakwaters is the rubble mound breakwater. These structures are constructed with smaller quarry rock as core and larger quarry rock as outer layer. For economical reasons, the design allows some damage to the armour layer. The amount of damage is...
master thesis 2012
document
Zwanenburg, S.A.A. (author)
The dimensions of single layer concrete armour units (interlocking armour units) are calculated with a similar stability relation as the stability relation for quarry stone. In these design formulas an 'average/significant' wave load is used (Hs). Since quarry stone gains its stability only from gravity, this type of armour unit is constructed...
master thesis 2012
document
Van de Koppel, M.A. (author)
Interlocking, single layer concrete armour units are placed in a specific grid depending on the type of armour unit. Within this grid, armour units are placed in horizontal rows. The number of horizontal rows of single layer armour units on a breakwater is limited to 20. This limit is proposed in order to prevent major settlements, which might...
master thesis 2012
document
Kik, R. (author)
The stability formula developed by Van der Meer is used for the design of different kind of rock slopes. In the formula is among a number of other parameters also the permeability of the structure represented. A more permeable structure has the ability to dissipate more water and therefore more energy, this results into a lower required weight...
master thesis 2011
document
Mingou, P. (author)
Breakwaters are important for the preservation and development of coastal areas. Submerged breakwaters have significant advantages compared to emerged, such as economical construction and preservation, milder effect on landscape and under conditions, preservation of marine flora and fauna inside it. The main objective of this study is to give...
master thesis 2011
document
Van Broekhoven, P.J.M. (author)
In JUMELET [2010] a method with a physical basis (so called “Volume Exchange model”) to determine the ‘notional’ permeability coefficient P was developed. The ‘notional’ permeability coefficient was previously introduced in the stability formula of the armour layer; see VAN DER MEER [1988]. In this latter study this coefficient was empirically...
master thesis 2011
document
Heuts, R.A.R. (author)
Along the northern coast of Morocco order has been given for the construction of a large transshipment port in the Mediterranean Sea, at a designated project location around the city of Nador. On this green-field coastal stretch a new transhipment port will have to be developed for various types of cargo. Throughputs of the terminals will have...
master thesis 2010
document
Lioutas, A.C. (author)
The overtopping empirical formulas calculate the discharge only at the top of the crest of a coastal protection structure. On the other hand, the tolerable overtopping discharges are defined at certain points behind the crest where the total overtopping is reduced. The scope of this thesis is to find an empirical formula to describe the...
master thesis 2010
document
Mulders, P.H.M. (author)
During the construction of breakwaters contractors often encounter undesired reshaping of exposed core material. This reshaping is comparable to the deformation process of berm breakwaters in which the outer profile reshapes into a more stable s-curve. In the case of oblique waves this deformation is enhanced by a longshore transport of stones...
master thesis 2010
document
Kersten, M.K. (author)
Albania has the following major sea ports: Durrës, Vlora, Sarandë and Shëngjin. The port of Durrës has the biggest share in the volume of import/export in Albania, nearly 75%. Due to current development rates, limited possibilities for expansion and pollution in the city because of its vicinity to the port, projects are identified to construct a...
master thesis 2010
document
Van der Linde, J.P. (author)
Two dimensional physical model tests are executed with Xbloc armour units on low crested structures to answer the objective. On the basis of findings in the literature study it can be expected that the stability of the Xbloc elements on low-crested breakwaters is a function of crest freeboard and crest width. The crest freeboard (Rc/Dn) varied...
master thesis 2009
document
Van Zwicht, B.N.M. (author)
This thesis is about the influence of the specific weight on the stability of single layer interlocking armour units on rubble mound breakwaters. The hydraulic stability of the Xbloc armour unit is expressed by the stability number which is based on the assumption of dominance of lift, drag and gravity forces. If other forces have significant...
master thesis 2009
document
Van Buchem, R.V. (author)
In an attempt to reduce the cost of breakwaters, several elements have been developed. Examples are Accropodes, Tetrapods and concrete cubes. Previous tests were performed with armour layers consisting of a double layer of cubes. This study is based on a single layer of cubes. The great benefit of a single layer of cubes is that it reduces the...
master thesis 2009
Searched for: department:"Hydraulic"
(1 - 20 of 42)

Pages