Searched for: subject%253A%2522Calcination%2522
(1 - 20 of 23)

Pages

document
Rahmani, Hossein (author)
The economic and environmental advantages of extrusion-based 3D concrete printing have made it a frontrunner in large-scale buildings. Nonetheless, this approach suffers from a contradictory rheological requirement and a high percentage of Portland cement (PC) in its mixture, which challenges its sustainability. It is claimed that the addition...
master thesis 2023
document
Chen, Y. (author), Zhang, Y. (author), He, S. (author), Liang, M. (author), Zhang, Yamei (author), Schlangen, E. (author), Copuroglu, Oguzhan (author)
Limestone-calcined clay-cement (LC3), as one of the most promising sustainable cements, has been under development over the past decade. However, many uncertainties remain regarding its rheological behaviors, such as the metakaolin content of calcined clay. This study aims to investigate the effect of increasing the content of fine-grained...
journal article 2023
document
Chen, Y. (author), Zhang, Y. (author), Šavija, B. (author), Copuroglu, Oguzhan (author)
Formulation of quaternary blended system containing ordinary Portland cement or clinker, slag, limestone and calcined clay (LC2) appeared to be a viable approach to developing low-clinker cements without severely sacrificing mechanical performance at later ages. This paper investigates the effect of two material parameters, i.e., LC2-to-slag...
journal article 2023
document
Chen, Y. (author), Liang, M. (author), Zhang, Y. (author), Li, Z. (author), Šavija, B. (author), Schlangen, E. (author), Copuroglu, Oguzhan (author)
Autogenous shrinkage may be a critical issue concerning the use of limestone-calcined clay-cement (LC3) in high-performance concrete and 3D printable cementitious materials, which have relatively low water to binder (W/B) ratio. Adding an internal curing agent, i.e., superabsorbent polymer (SAP), could be a viable solution in this context....
journal article 2023
document
Chen, Y. (author), Rahmani, Hossein (author), Schlangen, E. (author), Copuroglu, Oguzhan (author)
The implementation of extrusion-based 3D concrete printing (3DCP) in large-scale constructions is currently limited by concerns regarding rheology control and the sustainability of this process. To address these issues, this study presents an approach to develop limestone-calcined clay-based cementitious (LC3) materials accelerated by Ca(NO...
journal article 2023
document
Chen, Y. (author), Zhang, Y. (author), He, S. (author), Liang, X. (author), Schlangen, E. (author), Copuroglu, Oguzhan (author)
In 3D concrete printing, fast structuration is a prerequisite for ideal buildability. This paper aims to study the impact of inorganic additives, i.e., CaCl<sub>2</sub> and gypsum, on structural build-up and very early-age hydration of limestone-calcined clay-cement (LC3) pastes within the first 70–80 min. Results show that, increasing the...
journal article 2023
document
van Rijswijk, Tom (author)
Alkali activated concrete is seen as possible contender to alleviate the environmental footprint of the concrete industry. The goal of this research is to evaluate the extend to which ground granulated blast furnace slag and calcined clay-based alkali activated concrete can be utilized in concrete revetment applications with equal performance in...
master thesis 2022
document
Boudouan, Youssra (author)
After water, concrete is the most used substance on the planet. Approximately three tonnes of concrete is produced per person annually (Gagg, 2014). Traditionally, large amounts of Ordinary Portland Cement (OPC) are needed for the production of concrete. The production of OPC is very energy intensive and therefore a major generator of carbon...
master thesis 2022
document
Chen, Y. (author), Toosumran, Nuttapon (author), Chehab, Noura (author), Spanjers, H. (author), Copuroglu, Oguzhan (author)
This paper proposes the use of desalination brine as a setting and hydration activator in set-on-demand 3D concrete printing. A series of tests were conducted to investigate the effect of adding different concentrations of desalination brine on stiffness evolution and early-age hydration of Portland cement mortars (PC mixtures) and limestone...
journal article 2022
document
Chen, Y. (author)
Extrusion-based 3D concrete printing (3DCP), as one of the emerging techniques, has received considerable attention from both academia and industry, due to its numerous benefits for concrete construction, through enhancing the freedom of architectural design, eliminating formwork, optimizing material use, and decreasing wastes, labors and costs....
doctoral thesis 2021
document
Sui, Shiyu (author), Georget, Fabien (author), Jiang, Jinyang (author), Scrivener, Karen (author)
Chloride binding is an important factor for chloride transport in cementitious materials, which can fix the chloride on the solid phase and decrease the free chloride content. As an alumina-rich supplementary cementitious material, calcined clay can be applied to improve the binding capacity of the system. While the contribution of calcined clay...
conference paper 2021
document
Gonthier, Julien Nicolas (author), Wilson, William (author), Georget, Fabien (author), Scrivener, Karen (author)
The incorporation of supplementary cementitious materials (SCMs) in cement pastes enables both decreasing CO2 emissions and increasing the concrete durability, notably with a better resistance against chloride ingress and thus retarding the chlorideinduced corrosion of steel rebars. Nevertheless, a better understanding of the chloride fixation...
conference paper 2021
document
Chen, Y. (author), He, S. (author), Zhang, Y. (author), Wan, Z. (author), Copuroglu, Oguzhan (author), Schlangen, E. (author)
This paper aims to investigate the influences of high Portland cement substitutions (&gt;60 wt%) by low-grade calcined clay (CC) and limestone (LF) on 3D concrete printability, stiffness evolution and early-age hydration. Results show that, with the same dosage of admixtures (superplasticizer and viscosity modifier), increasing LF and CC...
journal article 2021
document
Anandakrishnan, Sundaram (author)
In this thesis, we focus on flexible haptic feedback applications which rely on the sensation of touch to display a feedback to the user that establishes a system to user interaction. Piezocomposites made of piezoceramic and polymer phases can be used here due to their high flexibility and piezoelectric properties that enable them to deform...
master thesis 2020
document
Chen, Y. (author), Chaves Figueiredo, S. (author), Li, Z. (author), Chang, Z. (author), Jansen, K. (author), Copuroglu, Oguzhan (author), Schlangen, E. (author)
In 3D concrete printing (3DCP), it is necessary to meet contradicting rheological requirements: high fluidity during pumping and extrusion, and high stability and viscosity at rest to build the layered structure. In this paper, the impact of the hydroxypropyl methylcellulose (HPMC)-based viscosity-modifying admixture (VMA) on the 3D printability...
journal article 2020
document
Chen, Y. (author), Romero Rodriguez, C. (author), Li, Z. (author), Chen, B. (author), Copuroglu, Oguzhan (author), Schlangen, E. (author)
This study aims to investigate the influences of different grades of calcined clay on 3D printability, compressive strength (7 days), and hydration of limestone and calcined clay-based cementitious materials. Calcined clays that contained various amounts of metakaolin were achieved by blending low-grade calcined clay (LGCC) and high-grade...
journal article 2020
document
Guatame-Garcia, Adriana (author), Buxton, M.W.N. (author)
In response to the growing demand for sustainable products and services, the kaolin calcination industry is developing practices that optimise the use of resources. The main challenges include more efficient use of raw materials and a reduction in the energy consumed by the calcination furnace. An opportunity to achieve this lies in the...
journal article 2020
document
Wei, L. (author), Zietzschmann, F.E. (author), Rietveld, L.C. (author), van Halem, D. (author)
In this study, F<sup>−</sup> removal by Ca–Al–CO<sub>3</sub> layered double hydroxides (LDHs) was investigated at environmentally-relevant concentration ranges (2–12 mg/L) to below the WHO guideline, with an emphasis on the effect of LDHs’ modification, as well as the effects of initial F<sup>−</sup> concentration, adsorbent dose, pH,...
journal article 2020
document
Chen, Y. (author), Yalçinkaya, Ç. (author), Copuroglu, Oguzhan (author), Schlangen, E. (author)
Recently, our group attempted to develop the ternary blended (Portland cement, calcined clay and limestone) cementitious material for 3D concrete printing (3DCP). Due to the elimination of formwork during the layer-by-layer casting process, the printed material should have favorable elastic properties and green strength at the fresh state. A...
conference paper 2019
document
Chen, Y. (author), Li, Z. (author), Chaves Figueiredo, S. (author), Copuroglu, Oguzhan (author), Veer, F.A. (author), Schlangen, E. (author)
The goal of this study is to investigate the effects of different grades of calcined clay on the extrudability and early-age strength development under ambient conditions. Four mix designs were proposed. Three of them contained high, medium, and low grades of calcined clay, respectively, and one was the reference without calcined clay. In terms...
journal article 2019
Searched for: subject%253A%2522Calcination%2522
(1 - 20 of 23)

Pages