Searched for: subject:"Aluminum%5C+alloy"
(1 - 20 of 33)

Pages

document
Eivani, A. R. (author), Vafaeenezhad, H. (author), Nikan, O. (author), Zhou, J. (author)
This research was aimed to assess the potential of a radial basis function (RBF) approximation method against the dislocation substructure-based constitutive model in predicting high-temperature deformation behavior of the AA7020 aluminum alloy. Hot compression tests were performed over a range of strain rate of 0.1–100 s<sup>−1</sup> and a...
journal article 2019
document
Dieleman, Christian D. (author), Denissen, P.J. (author), Garcia Espallargas, S.J. (author)
In this work, a new concept is introduced for active corrosion protection at damaged sites aiming at overcoming existing limitations of currently proposed strategies based on dispersed inhibitor-loaded nanocontainers in coatings. The underlying principle is based on the formation of low-density and/or humidity responsive interconnected paths...
journal article 2018
document
Zhang, X. (author)
Multiscale computational materials science has reached a stage where many complicated phenomena or properties that are of great importance to manufacturing can be predicted or explained. The word “ab initio study” becomes commonplace as the development of density functional theory has enabled the predictions to be independent of experimental...
doctoral thesis 2017
document
Bai, Sheng Wen (author), Fang, Gang (author), Zhou, J. (author)
The research was aimed to determine the effects of extrusion process condition on the weld seam quality of the aluminum alloy AA6082 by using a novel physical simulation method. A weld seam between two bars was formed under hydrostatic pressure in a specially designed die setup to simulate the longitudinal weld seam formation during extrusion...
journal article 2017
document
Norouzi Afshar, F. (author), Tichelaar, F.D. (author), Glenn, A. M. (author), Taheri, P. (author), Sababi, M. (author), Terryn, H.A. (author), Mol, J.M.C. (author)
This work studies the influence of the microstructure on the corrosion mechanism and susceptibility of as-brazed aluminum sheet. Various microstructures are obtained using postbrazing heat treatments developed to enhance the corrosion resistance of an AA4xxx/AA3xxx brazing sheet. The heat treatment results in a decrease of the matrix Si...
journal article 2017
document
Samaee, M. (author), Najafi, S. (author), Eivani, A. R. (author), Jafarian, H. R. (author), Zhou, J. (author)
In this research, grain refinement through severe plastic deformation (SPD) in combination with a thermal treatment to create a fine initial grain structure with a high degree of supersaturation was taken as a viable approach to achieving simultaneous increases in the hardness, strength and ductility of the aluminum alloy AA6063 during...
journal article 2016
document
Zhang, X. (author), Sluiter, M.H.F. (author)
Cluster expansions have proven a very useful tool to model thermodynamics and kinetics of substitutional alloys in metallic, ionic, and even covalently bonded systems. Cluster expansions are usually obtained with the structure inversion method in which the energies, or other relevant property, of a set of structures are used to obtain expansion...
journal article 2015
document
Zhang, L. (author)
The research in ultrasonic processing for metallurgical application shows a promising influence on improving casting properties of aluminium alloys. The principle of ultrasonic processing is introduction of acoustic waves with a frequency higher than 17 kHz into liquid metal. Several promising beneficial effects caused by ultrasonic processing...
doctoral thesis 2013
document
Ruiz-Ripoll, M.L. (author), Schut, H. (author), Benedictus, R. (author), Van der Zwaag, S. (author), Alderliesten, R.C. (author)
conference paper 2011
document
Lalpoor, M. (author), Eskin, D.G. (author), Ruvalcaba, D. (author), Fjaer, H.G. (author), Ten Cate, A. (author), Ontijt, N. (author), Katgerman, L. (author)
For almost half a century the catastrophic failure of direct chill (DC) cast high strength aluminum alloys has been challenging the production of sound ingots. To overcome this problem, a criterion is required that can assist the researchers in predicting the critical conditions which facilitate the catastrophic failure of the ingots. This could...
journal article 2011
document
Lalpoor, M. (author)
doctoral thesis 2010
document
Lalpoor, M. (author), Eskin, D.G. (author), Katgerman, L. (author)
journal article 2010
document
Lalpoor, M. (author), Eskin, D.G. (author), Katgerman, L. (author)
Non-homogenous cooling rates and solidification conditions during DC-casting of high strength aluminum alloys result in the formation and accumulation of residual thermal stresses with different signs and magnitudes in different locations of the billet. Rapid propagation of microcracks in the presence of thermal stresses can lead to catastrophic...
conference paper 2010
document
Lalpoor, M. (author), Eskin, D.G. (author), Katgerman, L. (author)
conference paper 2010
document
Lalpoor, M. (author), Eskin, D.G. (author), Katgerman, L. (author)
conference paper 2010
document
Lalpoor, M. (author), Eskin, D.G. (author), Katgerman, L. (author)
conference paper 2010
document
Eivani, A.R. (author)
doctoral thesis 2010
document
Schra, L. (author)
An interlaboratory testing programme to evaluate the rising displacement test for stress corrosion crack (SCO growth investigations was carried out within the framework of the "Measurements and Testing" programme of the European Community under BCR contract nr. MATI CT 930038. The contribution of the NLR to the project consisted of testing of...
report 1996
document
Wanhill, R.J.H. (author), Schra, L. (author)
An investigation was made of the effect of starter notch geometry on flight simulation fatigue crack growth in three damage tolerant aluminium sheet alloys, 2024-T3, 2091-T84 and 8090-T81. Changing the starter notch geometry resulted in significant differences in initial nonstabilized fatigue crack growth behaviour. However, there was only a...
report 1995
document
Wanhill, R.J.H. (author), Schra, L. (author), 't Hart, W.G.J. (author)
This report compares the mechanical properties, fracture toughness and fatigue crack growth properties of the damage tolerant/medium strength aluminium plate alloys 2024-T351, 2324-T39, 8090-T651 and 8090-T8171. The main objective, in view of previous work, was to determine whether damage tolerant 8090-T8171 plate can advantageously replace the...
report 1995
Searched for: subject:"Aluminum%5C+alloy"
(1 - 20 of 33)

Pages