- document
-
Wu, W. (author), Veljkovic, M. (author), Kolstein, M.H. (author), Pijpers, Richard (author), Maljaars, Johan (author)Steel Orthotropic Bridge Decks (OBDs) are widely used in long-span and movable bridges. Fatigue resistance analysis plays an important role in the design or assessment of OBDs. One possible fatigue failure is the crack initiating from the weld root of stiffener-to-deck plate connections at crossbeams. A full-scale experimental investigation...journal article 2024
- document
-
Simons, W.J.F. (author), Naeije, M.C. (author), Ghazali, Zaki (author), Darani Rahman, Wan (author), Cob, Sanusi (author), Kadir, Majid (author), Bin Mustafar, M.A. (author), Din, Ami Hassan (author), Efendi, Joni Efendi (author), Noppradit, Prakrit (author)Absolute sea-level rise has become an important topic globally due to climate change. In addition, relative sea-level rise due to the vertical land motion in coastal areas can have a big societal impact. Vertical land motion (VLM) in Southeast Asia includes a tectonically induced component: uplift and subsidence in plate boundary zones where...journal article 2023
- document
-
van Schelven, R.M. (author), Spirito, M. (author), Cavallo, D. (author)In this study, an efficient power combiner for mm-wave frequency transmitters is investigated. The combiner is based on a parallel plate waveguide (PPW) excited with multiple parallel feeds. The Doherty power combiner scheme is also integrated in the proposed concept, to increase the efficiency of the amplifiers when implementing amplitude...journal article 2023
- document
-
Takali, Farid (author), Nirwal, Sonal (author), Othmani, Cherif (author), Groves, R.M. (author)It has been shown that the roots of guided waves in laminate plates produced by the ordinary differential equations (ODE) approach may not hold under to some computational conditions. A particular drawback of the 2D formulation of the ODE approach is the lack of reliability in the case of unidirectional laminates due to the decoupling...journal article 2023
- document
-
Holkema, K. J. (author), Aalbers, C. (author), Wellens, P.R. (author)In head waves, water jet impacts due to run up can occur as a result of the structural configuration of some floating structures, reducing workability. Wave attenuation near the floater may reduce the risk of water jet impacts. This paper presents a numerical study of the performance and attenuation mechanisms of various plate type fixed free...journal article 2023
- document
-
Liao, D.L. (author), Cheng, L. (author), Correia, J.H.G. (author), Veljkovic, M. (author), Zhu, Shun Peng (author), Winkes, Jasper (author), Creusen, Koen (author), Berto, Filippo (author)Hole patterns are common in engineering design for connections and/or assembly purposes. Geometrical discontinuities can cause stress concentration in localized areas, making them more prone to fatigue crack initiation and influencing the fatigue life of the overall unit. In the past, much effort has been exerted on fatigue modelling of holed...journal article 2023
- document
-
Snieder, J. (author), Dielen, Marc (author), van Ostayen, R.A.J. (author)This work presents the development of a numerical model for the elastohydrodynamic lubrication of roll-to-plate nanoimprinting with flexible stamps. Roll-to-plate nanoimprinting is a manufacturing method to replicate micro- and nanotextures on large-area substrates with ultraviolet-curable resins. The roller is equipped with a relatively soft...journal article 2023
- document
-
Conde, Jorge (author), Simões da Silva, Luis (author), Francisca Santos, Ana (author), Lemma, Melaku Seyoum (author), Tankova, T. (author)The component method for joint analysis relies on the formulation of stiffness and strength of individual parts to derive the global properties of the joint. One of these components is the web of an open I-section, or the face of a rectangular hollow section, hereby referred to as face plate. It is currently not codified despite its frequent...journal article 2023
- document
-
Ebrahimi, Amin (author), Hermans, M.J.M. (author)Laser butt welding of thin metal sheets is a widely used fusion-based joining technique in industrial manufacturing. A comprehensive understanding of the complex transport phenomena during the welding process is essential for achieving high-quality welds. In the present work, high-fidelity numerical simulations are employed to investigate the...journal article 2023
- document
-
Brouwer de Koning, S. G. (author), de Winter, N. (author), Moosabeiki, Vahid (author), Mirzaali, Mohammad J. (author), Berenschot, A. (author), Witbreuk, M. M.E.H. (author), Lagerburg, V. (author)In orthopedic surgery, patient-specific bone plates are used for fixation when conventional bone plates do not fit the specific anatomy of a patient. However, plate failure can occur due to a lack of properly established design parameters that support optimal biomechanical properties of the plate. This review provides an overview of design...review 2023
- document
-
Toa, X. (author), Shen, Yunwei (author), Wang, Bo (author), Infante Ferreira, C.A. (author)High concentration NH<sub>3</sub>/H<sub>2</sub>O is suitable for Kalina cycles used for the recovery of low grade heat. Plate heat exchangers (PHEs) are compact and reduce the charge of working fluid. This paper investigates the condensation of NH<sub>3</sub>/H<sub>2</sub>O with NH<sub>3</sub> mass concentrations of 80%-96%. The vapor and...journal article 2023
- document
-
Han, C. (author)In the efficiency-driven photovoltaic (PV) industry, the market dominating crystalline silicon (c-Si) technology has been developing towards PV devices with carrier-selective passivating contacts (CSPCs). Especially, the silicon heterojunction (SHJ) solar cell, based on hydrogenated amorphous silicon (a-Si:H) contact stacks, and the poly-Si...doctoral thesis 2022
- document
-
Snieder, J. (author), Dielen, Marc (author), van Ostayen, R.A.J. (author)Roll-to-plate nanoimprinting with flexible stamps is a fabrication method to pattern large-area substrates with micro- and nanotextures. The imprint consists of the preferred texture on top of a residual layer, of which the thickness and uniformity is critical for many applications. In this work, a numerical model is developed to predict the...journal article 2022
- document
-
Lovato, S. (author), Kirichek, Alex (author), Toxopeus, S.L. (author), Settels, J.W. (author), Keetels, G.H. (author)When investigating the effect of muddy seabeds on marine vessels using Computational Fluid Dynamics (CFD) software, one challenge is to adequately describe the complex non-Newtonian fluid behaviour of mud. Although a number of rheological models have been proposed in the past, mud sediments are often simply regarded either as highly viscous...journal article 2022
- document
-
Gutierrez Alvarez, J. (author), Bisagni, C. (author)This paper presents an experimental and numerical study of composite plates, analyzing the interaction between mechanical and thermal loads related to buckling and the occurrence of mode jumping. A novel experimental setup for thermomechanical testing was developed. The setup is conceived around a frame with a low coefficient of thermal...journal article 2022
- document
-
Shahzad, H. (author), Hickel, S. (author), Modesti, D. (author)We perform direct numerical simulations of turbulent flow at friction Reynolds number Re<sub>τ</sub>≈ 500 - 2000 grazing over perforates plates with moderate viscous-scaled orifice diameter d<sup>+</sup>≈ 40 - 160 and analyse the relation between permeability and added drag. Unlike previous studies of turbulent flows over permeable surfaces,...journal article 2022
- document
-
Zhang, M. (author), Schreier, S. (author)Thin continuous flexible floating structures have been shown to have technical and economic advantages for Offshore Floating Photovoltaic (OFPV) installations. In terms of large horizontal dimensions compared to the wave length, these structures are similar to sea ice as well as Very Large Floating Structures (VLFS), e.g. as proposed for...review 2022
- document
-
Soman, Rohan (author), Fazzi, L. (author), Nokhbatolfoghahai, A. (author), Groves, R.M. (author), Ostachowicz, Wieslaw (author)To perform active structural health monitoring (SHM), guided waves (GW) have received great interest as they can inspect large areas with a few sensors and are sensitive to barely-visible structural damages. Fiber Bragg grating (FBG) sensors offer several advantages such as small size, low weight and ability to be embedded but their use has...conference paper 2022
- document
-
Rajora, A. (author), Haverkort, J.W. (author)Membraneless parallel-plate electrolyzers use electrolyte flow to avoid product crossover. Using a mixture model neglecting inertia, and assuming an exponential gas fraction profile, we derive approximate analytical expressions for the velocity profile and pressure drop for thin plumes. We verify these expressions using numerical solutions...journal article 2022
- document
-
Wang, Jue (author), Yuan, Weiyi (author), Li, Z. (author), Trofimov, Yuri (author), Lishik, Sergey (author), Fan, J. (author)Some atrial contractile assist devices applied on the heart surface can be regarded as a laminated Liquid crystal elastomer (LCE) plate under steady temperature loads and a contact mechanical force. An exact solution for the deformation of the laminated LCE plate under combined thermal and mechanical loads is derived by solving the three...journal article 2022