Pages
- 1
- 2
- document
-
Traka, K. (author)The present thesis investigates recrystallization and related phenomena in interstitial free (IF) and low carbon (LC) microstructures. Emphasis is given mostly on the early stages of recrystallization, i.e. nucleation stage. The investigations are performed with experimental measurements and computer simulations. In all studies,...doctoral thesis 2022
- document
-
Eipe, Jonathan Joe (author)The Static Recrystallization (SRX) phenomenon of austenite in C-Mn steels have a large impact on the final mechanical properties of the steel. However, the austenite recrystallization kinetics are difficult to investigate experimentally, due to solid-state phase transformations during cooling to room temperature. The best model alloys to examine...master thesis 2021
- document
-
Nguyen-Minh, T. (author)Texture and anisotropy are persistent characteristics of polycrystal. Because of the ordered and periodic arrangement of atoms in crystal lattices, responses of each oriented crystals in a polycrystal to the same external forces are not similar. Crystal grains which are better accommodated to boundary conditions because of their energetically...doctoral thesis 2021
- document
-
Mohseni, M. (author), Eivani, A.R. (author), Vafaeenezhad, H. (author), Jafarian, H. R. (author), Salehi, M. T. (author), Zhou, J. (author)The mechanical properties of a magnesium alloy strongly depend on its grain structure. It is desirable to minimize grain growth during the post-forming annealing treatment, thereby minimizing the loss in strength while regaining ductility. In the present research, the annealing of the hot-rolled AZ61 Mg alloy at different temperatures for...journal article 2021
- document
-
Imanian Ghazanlou, Siavash (author), Eghbali, Baitallah (author), Petrov, R.H. (author)The effects of the post-deformation annealing on the microstructural evolution of hot rolled Al7075 matrix composites reinforced with CNTs and GNPs were investigated. The multi-pass hot rolling was applied on the stir cast samples. Annealing was then applied to the composites at 450 °C for 4 h. Microstructural evolution was examined by SEM,...journal article 2021
- document
-
Lan, H. (author), Tang, S. (author), DU, Linxiu (author), LI, Jianping (author), van der Zwaag, S. (author)The combined effects of the initial microstructure and heating rate on ferrite recrystallization, austenite formation and transformation kinetics of a regular ferrite-martensite dual phase steel are investigated. Special attention is given to the effect of the martensite distribution on mechanical properties, particularly the bendability....journal article 2021
- document
-
Traka, K. (author), Sedighiani, K. (author), Bos, C. (author), Galan Lopez, J. (author), Angenendt, Katja (author), Raabe, Dierk (author), Sietsma, J. (author)A cellular automaton algorithm for curvature-driven coarsening is applied to a cold-rolled interstitial-free steel's microstructure - obtained through electron backscatter diffraction (EBSD). Recrystallization nucleation occurs naturally during the simulation, due to the highly heterogeneous and hence competitive growth among pre-existing ...journal article 2021
- document
-
Gilgannon, James (author), Poulet, Thomas (author), Berger, Alfons (author), Barnhoorn, A. (author), Herwegh, Marco (author)Creep cavities are increasingly recognized as an important syn-kinematic feature of shear zones, but much about this porosity needs investigation. Largely, observations of creep cavities are restricted to very fine grained mature ultramylonites, and it is unclear when they developed during deformation. Specifically, a question that needs...journal article 2020
- document
-
Shah, Vitesh (author), Krugla, M. (author), Offerman, S.E. (author), Sietsma, J. (author), Hanlon, David Neal (author)This study presents the effects of silicon (Si) and manganese (Mn) concentration and of heating rate on the ferrite recrystallization kinetics in seven model alloys with different Si and Mn concentrations, which are of relevance for the development of Advanced High Strength Steels (AHSS). The recrystallization kinetics were studied with in...journal article 2020
- document
-
Banis, Alexandros (author), Hernandez Duran, E.I. (author), Bliznuk, Vitaliy (author), Sabirov, Ilchat (author), Petrov, R.H. (author), Papaefthymiou, Spyros (author)The effect of ultra-fast heating on the microstructures of steel has been thoroughly studied over the last year as it imposes a suitable alternative for the production of ultra high strength steel grades. Rapid reheating followed by quenching leads to fine-grained mixed microstructures. This way the desirable strength/ductility ratio can be...journal article 2019
- document
-
Diehl, Martin (author), Kertsch, Lukas (author), Traka, K. (author), Helm, Dirk (author), Raabe, Dierk (author)Low-alloyed steels with body-centered cubic crystal structure are a material class that is widely used for sheet metal forming applications. When having an adequate crystallographic texture and microstructure, their mechanical behavior is characterized by an isotropic in-plane flow behavior in combination with a low yield strength. The...journal article 2019
- document
-
Rosas Saad, Jorge A (author)Because of its extraordinary material properties, like its high melting point and thermal stress resistance, low erosion and swelling rate, and high radiation damage resistance, highly deformed pure tungsten has been chosen as the plasma facing surface material for the ITER reactor divertor. The study of tungsten’s recrystallization behavior and...master thesis 2018
- document
-
Eivani, A.R. (author), Zhou, J. (author)In this research, hot compression test is used to simulate the metallurgical phenomena occurring in the peripheral part of AA7020 aluminum alloy extrudates during hot extrusion and leading to the formation of the peripheral coarse grain (PCG) structure. The temperature profiles at a tracking point in the peripheral part of extrudates are...journal article 2017
- document
-
Bai, Sheng Wen (author), Fang, Gang (author), Zhou, J. (author)The research was aimed to determine the effects of extrusion process condition on the weld seam quality of the aluminum alloy AA6082 by using a novel physical simulation method. A weld seam between two bars was formed under hydrostatic pressure in a specially designed die setup to simulate the longitudinal weld seam formation during extrusion...journal article 2017
- document
-
Jiao, F. (author), Mohles, V. (author), Miroux, A.G. (author), Bollmann, C. (author)Microstructure and microchemistry evolution during hot deformation and subsequent annealing of a commercial Al-Mg-Si alloy were experimentally investigated using electron backscatter diffraction (EBSD) and SEM. Meanwhile, a through-process model framework consisting of the deformation model GIA-3IVM+ and the recrystallization (RX) model CORe was...conference paper 2014
- document
-
Galindo Nava, E.I. (author)This work aims to describe plastic deformation and microstructure evolution of metals at various scales in terms of dislocation behaviour. The theory is based on statistical thermodynamics, where the entropy is proposed to incorporate the possible paths for dislocation motion. Other than estimating the velocity gradients a dislocation may reach,...doctoral thesis 2013
- document
- Eivani, A.R. (author) doctoral thesis 2010
- document
-
Smith, A. (author)Abstract not availabledoctoral thesis 2006
- document
-
Gaertner, R.S. (author)Investigation of the reactive recrystallization of trona (sodium sesquicarbonate) and sodium bicarbonate to sodium carbonate (soda) in a mixed solvent led to the design of several alternative, less energy consumptive, economically very attractive process routes for the production of soda from all principal sodium carbonate sources. The kinetics...doctoral thesis 2005
- document
-
Chen, S.P. (author)Microstructural modeling of thermomechanical processing is well established as a valuable procedure for optimizing processing conditions in the steel industry, while the similar work for aluminum industry is still an opening problem. Recovery, recrystallization and grain growth are core elements of this processing. This thesis concentrates on...doctoral thesis 2003
Pages
- 1
- 2