- document
-
Iványi, Charlotte (author)Laser-assisted fiber placement (LAFP) is a promising manufacturing process for thermoplastic composites (TPCs), which enables out-of-autoclave production and eliminates post-consolidation steps. In LAFP, thermoplastic carbon fiber tapes are heated with a laser heat source and placed into the desired layup with the help of a robot, while being...master thesis 2023
- document
-
Hendriksen, Luuk (author)Aerodynamic load determination through integration of the surface pressure distribution is limited in accuracy by the discrete number of measurements taken. Therefore, typically relatively large numbers of spatially distributed measurements are required which increase setup complexity, latency, cost and weight while requiring physical access in...master thesis 2022
- document
-
Datta, Sattama (author)With the increasing environmental concerns, the world is moving towards rapid decarbonization, and to meet the growing energy demand, more renewable energy sources like solar, Wind are getting added to the existing Distribution grid. The addition of new loads like Electric vehicles (EV), Heat pumps, etc. is putting additional pressure on the...master thesis 2022
- document
-
Vehmeijer, Reinoud (author)Subsea rock installation is a process in offshore engineering where rocks are placed on the seabed or subsea structures using a fallpipe. An example of a subsea structure could be a cable or pipeline that must be protected. In this research, the main scope is rock installation for scour protection of the foundation of offshore wind turbines. As...master thesis 2022
- document
-
Hijne, Max (author)The development of novel materials has been of great interest to the aerospace industry in the pursuit of efficiency and cost reduction. Fibre-steered variable stiffness laminates have promising characteristics due to the ability to better tailor designs for expected loading, as the fibre orientation can be varied within a layer. This thesis was...master thesis 2022
- document
-
Blommert, Yannick (author)Laser-assisted automated fiber placement (LAFP) is a promising additive manufacturing technique for the production of large aerospace components. Thermoplastic prepreg tapes will be placed ply-by-ply on top of a mould and in-situ consolidated. This is beneficial for higher production rates. The mechanical performance of thermoplastic composite...master thesis 2022
- document
-
Plas, Nicolas (author)Software-Defined Networking (SDN) is a relatively new networking paradigm that proposes to separate the control and the data logic in networks. The control logic is centralized in a controller, which allows for a programmable network. SDN is promising but also intro- duces some critical security vulnerabilities to networks. This work proposes a...bachelor thesis 2022
- document
-
Meister, S. (author)In modern aircraft, structural lightweight composite components are increasingly<br/>used. To manufacture these components in a costeffective way, robust production systems for the manufacturing of complex fibre composite components are necessary. A rather novel but already established process for fibre material deposition is the Automated Fibre...doctoral thesis 2022
- document
-
Mora Benitez, Christian (author)Fused deposition modeling (FDM) is one of the fastest-growing additive manufacturing processes in recent years. Nevertheless, the mechanical properties cannot be matched to those of traditional manufacturing methods such as injection molding.The research presented in this report aims to demonstrate the limitations of fusion deposition models and...master thesis 2022
- document
-
Experimental and numerical study of bending-induced buckling of stiffened composite plate assembliesTelford, R. (author), Peeters, D.M.J. (author), Rouhi, M. (author), Weaver, P. M. (author)Despite their importance in benchmarking numerical simulations, buckling tests still feature compromises between component-level and high-fidelity large-scale tests. For example, compression-induced buckling tests cannot capture the through-thickness or span-wise stress gradients in wing skins. Consequently, the results obtained often require...journal article 2022
- document
-
Zheng, Zixuan (author), Zheng, Feifei (author), Bi, Weiwei (author), Du, Jiawen (author), Duan, Huan-Feng (author), Savić, Dragan (author), Kapelan, Z. (author)An early contamination warning system with deployed water quality sensors is often used to enhance the safety of a water distribution system (WDS). While algorithms have been developed to select an optimal water quality sensor placement strategy (WQSPS) for WDSs, many of them do not account for the influences caused by future uncertainties,...journal article 2022
- document
-
van Campen, J.M.J.F. (author)Significant improvements in the mechanical performance of a laminated composite structure can be achieved by spatial variation of the stiffness properties within the laminate. Such a variable stiffness (VS) laminate, typically is created by steering the fibers within the laminae, resulting in an in-plane variation of stacking sequence and thus...conference paper 2022
- document
-
Meister, S. (author), Kolbe, Andreas (author), Groves, R.M. (author)The demand for efficient composite production processes is growing as the proportion of composites in modern aircraft increases. Particularly, thermoplastic composites are interesting for sustainability and cost efficiency. They can be manufactured using deposition methods, which involve heating by radiation in the visible and near-infrared...journal article 2022
- document
-
Romero, Daniel (author), Viet, Pham Q. (author), Leus, G.J.T. (author)Mobile base stations on board unmanned aerial vehicles (UAVs) promise to deliver connectivity to those areas where the terrestrial infrastructure is overloaded, damaged, or absent. A fundamental problem in this context involves determining a minimal set of locations in 3D space where such aerial base stations (ABSs) must be deployed to provide...conference paper 2022
- document
-
Schallig, Wouter (author), van den Noort, Josien C. (author), Piening, Marjolein (author), Streekstra, Geert J. (author), Maas, Mario (author), van der Krogt, Marjolein M. (author), Harlaar, J. (author)Background: Foot and ankle joint kinematics are measured during clinical gait analyses with marker-based multi-segment foot models. To improve on existing models, measurement errors due to soft tissue artifacts (STAs) and marker misplacements should be reduced. Therefore, the aim of this study is to define a clinically informed, universally...journal article 2022
- document
-
Peeters, D.M.J. (author), Jones, David (author), O'Higgins, Ronan (author), Weaver, Paul M. (author)Over the past 25 years, interest in thermoplastic composites in aircraft has steadily increased. Combining winding and laser-assisted tape placement is a promising method to manufacture thermoplastic structures using in-situ consolidation, as shown recently by manufacturing a variable stiffness, unitized, integrated-stiffener thermoplastic...journal article 2022
- document
-
Uchida, Thomas K. (author), Seth, A. (author)Estimating kinematics from optical motion capture with skin-mounted markers, referred to as an inverse kinematic (IK) calculation, is the most common experimental technique in human motion analysis. Kinematics are often used to diagnose movement disorders and plan treatment strategies. In many such applications, small differences in joint...journal article 2022
- document
-
Jimenez del Toro, A. (author), Teuwen, Julie J.E. (author), Tomás, Flanagan (author), Finnegan, William (author)Laser-assisted tape placement (LATP) and thermoplastic composites (TPCs) pre-impregnated (prepreg) tapes are a promising combination of technologies; given the in-situ capabilities of the TPCs and the high degree of automation achievable with LATP. However, laminate quality, measured as final void content, tends to decrease when increasing...conference paper 2022
- document
-
Swamy, A. (author)The intraoperative guidance and placement of spinal screws is a complex procedure. High technical expertise is required fromthe surgeons in order to achieve adequate fixation and ensure patient safety by preventing vascular and neurological injuries. The conventional screw placement techniques face several challenges. Surgeons heavily rely on...doctoral thesis 2021
- document
-
van Kollenburg, Jos (author)The aerospace industry increasingly uses fibre-reinforced plastics that are manufactured using automated fibre placement (AFP). A common problem in AFP is the occurrence of gaps and overlaps that affect the structural perfromance of laminates. Tow width fluctuation is an important cause of gaps and overlaps. Two developments in manufacturing are...master thesis 2021