The landing gear system is the dominant airframe noise source for most modern commercial aircraft during approach. This manuscript reports the results from the ALLEGRA (Advanced Low Noise Landing (Main and Nose) Gear for Regional Aircraft) project. This project assessed the performance of several highly realistic low–noise technologies (LNTs) applied to a detailed full–scale nose landing gear (NLG) model in aeroacoustic wind–tunnel experiments. Four individual low–noise concepts tested, namely a ramp door spoiler, a solid wheel axle fairing, wheel hub caps, and multiple perforated fairings. Combinations and small variations of some of these LNTs were also evaluated. The use of multiple planar microphone arrays allowed for the application of 2D and 3D acoustic imaging algorithms to assess the location and strength of the noise sources within the NLG system in different emission directions for each configuration. The wheel axle, the inner wheel hubs, the steering pinions and the torque link were identified as the noisiest NLG elements. The solid wheel axle fairing was the most effective individual LNT, and it improved its performance when applied in combination with the ramp door spoiler and wheel hub caps, reaching overall noise reductions of more than 4 dBA.

@en

The noise emissions of a full-scale nose landing gear (NLG), measured in a wind tunnel and obtained from computational simulations, are compared with those of three regional aircraft types recorded in flyover measurements. A comparison is made with the noise prediction models of Fink, Guo, and German Aerospace Center (DLR). A good agreement was found between all the spectra. The noise emissions up to 1.2 kHz were found to scale with the sixth power of the flow velocity, as usual; however, the spectra at higher frequencies collapsed better when scaled to the seventh power, confirming the fact that high-frequency noise is radiated from the turbulent flow surrounding small features of the NLG. Microphone arrays showed that the main noise sources were located in the middle of the wheel axle. For the flyovers and computational simulations, strong tonal peaks (at around 2200 Hz) were found, which are likely to be caused by open cavities in the NLG. This phenomenon is not accounted for in prediction models. Removing these tones would result in noise reductions of up to 2 dB. Thus, it is highly recommended to include cavity-noise estimations in the current prediction models, or to simply eliminate such cavities where possible with the use of cavity caps.

@en

The purpose of this work is to check if additive manufacturing technologies are suitable for reproducing porous samples designed for sound absorption. The work is an inter-laboratory test, in which the production of samples and their acoustic measurements are carried out independently by different laboratories, sharing only the same geometry codes describing agreed periodic cellular designs. Different additive manufacturing technologies and equipment are used to make samples. Although most of the results obtained from measurements performed on samples with the same cellular design are very close, it is shown that some discrepancies are due to shape and surface imperfections, or microporosity, induced by the manufacturing process. The proposed periodic cellular designs can be easily reproduced and are suitable for further benchmarking of additive manufacturing techniques for rapid prototyping of acoustic materials and metamaterials.@en

The noise emissions of a full-scale nose landing gear, measured in a wind tunnel and obtained from computational simulations, are compared with those of three regional aircraft types recorded in flyover measurements. The results from these three approaches are also compared with the predictions of two airframe noise models (Fink and Guo). The geometries of the nose landing gears in all cases were similar. Microphone arrays and acoustic imaging algorithms were employed to estimate the sound emissions of the nose landing gears. A good agreement was found between the overall trends of the frequency spectra in all cases. Moreover, the expected 6th power law with the flow velocity was confirmed. On the other hand, strong tonal peaks (at around 2200 Hz) were only found for the flyover tests and computational simulations and are not present in typical noise prediction models. As the frequencies of the tones did not depend on the flow velocity, they are likely to be caused by cavities found in structural components of the nose landing gear. Removing these tones would cause overall noise reductions up to 2 dB in the frequency range examined. The noise emissions in the side direction did not present tonal peaks. The acoustic source maps showed that the dominant noise sources were located in the middle of the wheel axle, followed by the main strut and the bay doors. It is, therefore, recommended to further investigate this phenomenon, to include cavity-noise estimations in the current noise prediction models, and to eliminate such cavities where possible with the use of cavity caps, for example.

@en