The development of new wind farm control strategies can benefit from combined analysis of flow dynamics in the farm and the behavior of individual turbines within one simulation environment. In this work, we present such an environment by developing a new coupling between the large-eddy simulation (LES) code GRASP and the multiphysics wind turbine simulation tool OpenFAST via an actuator line model (ALM). In addition, the implementation of the recently proposed filtered actuator line model (FALM) within the coupling is described. The new ALM implementation is cross-verified with results from four other commonly used research LES codes. The results for the blade loads and the near wake obtained with the new coupling are consistent with the other codes. Deviations are observed in the far wake. The results further indicate that the FALM is able to reduce the lift and power overprediction from which the traditional ALM suffers on coarse LES grids. This new simulation environment paves the way for future wind farm simulations under realistic weather conditions by leveraging GRASP's ability to impose data from large-scale meteorological models as boundary conditions.

In the past, fin-and tube heat exchanger (FTHE) tube pattern ratios have been largely based on ad-hoc design principles. Here, we investigate the optimal tube arrangements for a FTHE with plain fins in marine environments represented by two different air types; one for unfiltered air with high condensation rate and one for clean dry filtered air conditions. The thermal-hydraulic efficiency of the FTHE design is measured by comparing a modified ratio of Colburn j-factor and Fanning friction factor. The regression model generated from the CFD data is then used to identify the maximum efficiency for two design specific fin pitches separately. We identified two optimal tube patterns: one for a large fin pitch for unfiltered air, and another for a small fin pitch for filtered air. Manufacturing restrictions were found to significantly limit the maximum achievable efficiency of a tube pattern. By neglecting the related manufacturing restrictions, 4% higher efficiency for a fin pitch of 1.5 mm and 23% higher efficiency for a fin pitch of 3.5 mm is achieved. Without any application specific limitations or manufacturing restrictions the fin pitch 1.5 mm can have a 36% increased efficiency than fin pitch 3.5 mm. These novel results show that development in manufacturing have potential for significant improvements in thermal-hydraulic efficiency.

In this work we present Reynolds-averaged Navier-Stokes (RANS) simulations of the flow past the constant design shape of a leading-edge inflatable (LEI) wing. The simulations are performed with a steady-state solver using a k-ω SST turbulence model, covering a range of Reynolds numbers between 10⁵ ≤ and ≤ 15 × 10⁶ and angles of attack varying between-5° and 24°, which are representative for operating conditions in airborne wind energy applications. The resulting force distributions are used to characterize the aerodynamic performance of the wing. We found that a γ-Re_θ transition model is required to accurately predict the occurrence of stall up to at least Re= 3 × 10⁶. The work highlights similarities with the flow past a two-dimensional LEI airfoil, in particular, with respect to flow transition and its influence on the aerodynamic properties. The computed values of the lift and drag coefficients agree well with in-flight measurements acquired during the traction phase of the LEI wing operation. The simulations show that the three-dimensional flow field exhibits a significant cross flow along the span of the wing.

In this paper we present a computational approach to simulate the steady-state aeroelastic deformation of a ram-air kite for airborne wind energy applications. The approach is based on a computational fluid dynamics (CFD) solver that is two-way coupled with a finite element (FE) solver. All components of the framework, including the meshing tools and the coupling library, are available in open source. The flow around the wing is described by the steady-state Reynolds-averaged Navier-Stokes (RANS) equations closed by an SST turbulence model. The FE model of the cellular membrane structure includes a wrinkling model and uses dynamic relaxation to find the deformed steady-state shape. Each simulation comprises four distinct steps: (1) generating the FE mesh of the design geometry, (2) pre-inflation of the wing, applying a uniform pressure on the inside, (3) generating the CFD mesh around the pre-inflated wing, and (4) activating the exterior flow and two-way coupling iterations. We first present results for the aerodynamics of the pre-inflated rigid ram-air wing and compare these to similar results for a leading edge inflatable (LEI) tube kite. Both wings are characterized by a high anhedral angle and low aspect ratio which induce spanwise flows that reduce the aerodynamic performance. The comparison shows a better performance for the LEI wing which can be attributed to its higher aspect ratio. The aeroelastic deformation of the ram-air wing further improves the aerodynamic performance, primarily because of the increasing camber which in turn increases the lift force. A competing aeroelastic phenomenon is the formation of bumps near the leading edge which increase the drag.

Vortex-induced vibrations (VIVs) of wind turbine towers can be critical during the installation phase, when the rotor-nacelle assembly is not yet mounted on the tower. The present work uses numerical simulations to study VIVs of a two-dimensional cylinder in the transverse direction under flow conditions that are representative of wind turbine towers both from a fluid dynamics and structural dynamics perspective. First, the numerical tools and fluid-structure interaction algorithm are validated by considering a cylinder vibrating freely in a laminar flow. In that case, both the motion amplitude and frequency are shown to agree well with previous results from the literature. Second, VIVs are modelled in the turbulent supercritical regime using unsteady Reynolds-averaged Navier-Stokes equations. In this context, the turbulence model is first validated against flow past a stationary cylinder with a high Reynolds number. Then, the results from forced vibrations are validated against experimental results for a range of reduced frequencies and velocities. It is shown that the behaviour of the aerodynamic damping changes with the frequency ratio and can therefore lead to either self-limiting or self-exciting VIVs when the cylinder is left to freely vibrate. Finally, results are shown for a freely vibrating cylinder under realistic flow and structural conditions. While a clear lock-in map is identified and shows good agreement with published numerical and experimental data, the work also highlights the unsteady nature of the aerodynamic forces and motion under certain operating conditions..