Thermoplastic composite spot welded joints are more well-suited for carrying shear load rather than peel load. However, peel load is difficult to be eliminated in single-lap joint configuration. In this paper, a series of mechanical tests were carried out to study the effects of the spot spacing and the number of welded spots on the secondary bending and subsequently on the strength of the multi-spot welded joints. Based on that, a comparative study was performed on the load-carrying capability of multi-spot welded and mechanically fastened joints assembled with multi-row fasteners. It was found that, by increasing the spot spacing and the number of welded spots, the secondary bending of the multi-spot welded joints can be effectively decreased, which eventually results in a comparable load-carrying capability with respect to the mechanically fastened joints.

@en

In previous work, single-spot ultrasonically welded joints were found to feature similar load carrying capability in shear but significantly low capability in peel as joints with a representative single-mechanical fastener. This leads to questioning welding as an appropriate solution for the commonly-used single-lap joint configuration. The present paper investigates the mechanical performance of spot welded single-lap joints in thermoplastic composites in comparison to their mechanically fastened counterparts. Single-row joints, double-row joints with varying inter-row distance and multi-row joints with varying number of rows were investigated in this study. The results showed that, owing to higher joint stiffness and hence lower secondary bending and peel stresses, the load carrying capability of the spot welded joints was comparable to that of the mechanically fastened joints in all considered cases. Likewise, the effects of increasing the inter-row distance and of increasing the number of rows were similar for both types of the joints.

@en

The research in this paper is an essential part of a bigger effort on developing robust sequential ultrasonic welding of multi-spot welded joints in thermoplastic composites. It mainly focused on assessing the impact of the changes in boundary conditions on the welding process and whether it could be circumvented by using an appropriate process control strategy. A two-step approach was followed by investigating: (1) the effect of boundary conditions on displacement- and energy-controlled single-spot welded joints and (2) displacement- and energy-controlled sequential ultrasonic welding of double-spot welded joints. The results showed that previous spots indeed affect the energy required to obtain an optimum new welded spot, which challenges the use of energy-controlled welding for this application. Contrarily, displacement-controlled welding was shown to provide consistent-quality welds with a constant set of welding parameters and it was hence identified as the most promising welding strategy for sequential ultrasonic welding of thermoplastic composites.

@en

The popularity of thermoplastic composites (TPCs) has been growing steadily in the last decades in the aircraft industry. This is not only because of their excellent material properties, but also owing to their fast and cost-effective manufacturing process. Fusion bonding, or welding, is a typical joining method for TPCs due to the intrinsic properties of thermoplastic polymers. Among different welding technologies, ultrasonic welding has been regarded as one of the most promising techniques for the assembly of TPC components. Ultrasonic welding is by nature a spot welding technique. As it is known that a series of problems result from using mechanical fasteners for joining composite structures, e.g. breaking fibres during drilling and extensive labour work, ultrasonic spot welding can be considered as a promising alternative from the perspective of fast manufacturing cycle. However, fundamental understanding is still lacking to achieve application of ultrasonic spot welding in composite structures to be achieved: @en

Ultrasonic welding is a promising assembly technique for thermoplastic composites and it is well-suited for spot welding. In this study, two typical welding process control strategies, i.e. displacement-controlled and energy-controlled welding, were selected to manufacture spot-welded joints. The influence of different boundary conditions, provided by different welding jigs, on the welding process and the performance of thus-created welded joints were investigated. The optimum input energy was found dependent on the welding jigs, while the optimum displacement was consistent for achieving the maximum weld strength in both welding jigs. Therefore, displacement-controlled welding showed more potential in producing consistent welds in sequential multi-spot welding.@en

This paper mainly investigates the impact of changes in boundary conditions on the welding process and the variability of the created spot-welded joints. The experimental results provides a good base for manufacturing and investigation of the ultrasonic multi-spot welded joints in thermoplastic composites. @en

The in-plane and out-of-plane mechanical behaviour of both ultrasonically spot-welded and mechanically fastened joints was investigated by double-lap shear and pull-through tests, respectively. Spot-welded specimens showed comparable onset failure load and significantly higher joint stiffness compared to mechanical fasteners when carrying shear load. The failure modes and the damage within specimens were analysed after mechanical tests. Intralaminar failure and very limited damage on the out-most ply were found for welded specimens, whereas catastrophic through-the-thickness failure was observed for mechanically fastened joints. Based on the experimental outcomes, the mechanical performance and failure mechanisms of spot-welded joints were critically assessed in comparison to the mechanical fasteners . @en

Ultrasonic welding is a promising assembly technique for thermoplastic composites and it is well-suited for spot welding. In this paper, the in-plane and out-of-plane mechanical behaviour of ultrasonically spot-welded and mechanically fastened joints are investigated by double-lap shear and pull-through tests, respectively. Special attention was paid to the comparison of onset failure load and joint stiffness of both types of joints in either type of test. Fractography was utilized to analyse the teste specimens. Failure of welded specimens was found limited in the joints but catastrophic damage was introduced into composite substrates of mechanically fastened specimens. The possibility of the substitution for mechanically fastened joints by spot-welded joints is discussed. @en