Currently, there is no infrastructure between the two Indonesian islands Flores and Adonara. The islands are separated by the Larantuka Strait, which has a width varying between 600 and 1000 meters. The local government would like a bridge between the two islands. However, as the water in the 18 meter deep strait is heavily subjected to tidal forces - creating a tidal amplitude of about 1.5 m and tidal flow velocities ranging up to 4.5 m/s - structural design is challenging. As traditional bridges were deemed too expensive, a new type of bridge was introduced: the `Tidal Bridge'. The pendulum founded floating bridge, which is proposed to span the deepest 400 meters of the cross-section, is designed with tidal turbines attached to the bottom of the structure. The energy production mitigates the financial burden that the 225 million US dollar Palmerah Tidal Bridge will bring. At the time of writing, a pre-feasibility study has been performed by Antea, proposing initial structural dimensions. BAM took over the design process, which lead to questions regarding the dynamic stability of the design. The objective of this report is to answer the following two research questions: 1. How can the dynamic response due to two-dimensional forcing of a Tidal Bridge be determined? 2. What design choices can further optimise the dynamic behaviour of a Tidal Bridge? A numeric tool has been created to predict the dynamics of the proposed design as function of an input of wind, waves, and current. Based on (experimental) literature, hydrodynamic coefficients determining the fluid-structure interaction were determined. The complex shape of the floaters did not allow appropriate validation of the accompanying added mass and radiation damping coefficients. Comparison with a model constructed in Ansys Aqwa showed values of similar magnitude, but precise magnitudes could not be determined. In order to find these important coefficients, a set of experiments has been performed to determine the added mass (moment of inertia) and radiation damping (moment of inertia) for heave and roll motion. The experiments showed that the added mass equations for heave were well defined, while the added mass moment of inertia equations for roll motion deviated up to 250 per cent. The acquired data was used to find better relations between the added mass (moment of inertia) and the floater dimensions. Please note, the empirical relations are based on limited data and with little mathematical background. Hence, the relations should be used with care. The radiation damping coefficients that were also extracted from the experiments showed no clear trend, but did confirm that the hand-calculations were of correct magnitude. Using the constructed model, forcing characteristics of the Tidal Bridges are investigated. In these computations, the Palmerah Tidal Bridge dimensions are used as a case study. It was noted that the extreme non-linearity of different elements of the problem (changing pendulum angle, hydrodynamic pressure field, and particle velocity/acceleration field) do not allow for linear approximation. While a linear mass-spring system predicts that the natural period is about 6.7 seconds, the maximum dynamic amplitude is found for wave periods of 9 seconds. This coincides with the largest expected waves for the Palmerah Tidal Bridge location. Reducing the natural period of the design is recommended. Additionally, research was done into the contribution of the various types of forcing, where it was found that traffic weight has negligible effect on the dynamics. Wind forces add only a few percent to the pendulum forces, but do have a significant contribution to the displacements. Furthermore, research into the impact of an approaching wave field showed that accelerations during first impact may overshoot the maximum steady state acceleration by more than 200 per cent. A parametric study on the dynamics of Tidal Bridges was performed, which did research into the the forcing combinations that lead to most amplification of the dynamics. It shows that different loading combinations are governing for accelerations in the three different degrees of freedom present in a two-dimensional system. In here, difference was found for the dynamic behaviour induced by waves from the two different wave directions, leading to two sets of three forcing combinations. This data was used to investigate the effect of three design parameters: the angle of the pendulum, the hinge location of the pendulum and the depth of the strait. Moreover, a sensitivity study is performed on a set of parameters defining the Tidal Bridge. It shows that the mass of the segment, the added mass, the floater length, the design turbine force, and the pendulum angle are most important if it comes to design optimisation. Based on the parametric study and the forcing characteristics, conclusions and recommendations are made for improvements of Tidal Bridge designs in general and more specifically: the Palmerah Tidal Bridge.

At the Shonai River around Nagoya, Japan, several flood related problems occur. These problems occur at different locations, each with its own problems or limitations. The desired safety level as requested by the government is that the river should be able to have a discharge which has a probability of failure of once in 200 years. At many locations, the current probability of failure is lower than once in 50 years. This has led to the following research question:
How can the discharge capacity of the Shonai River be improved to modern standards?
The report has been divided in four phases. The first phase is used to formulate the final research question. This phase focuses on which part of the Nagoya urban area is most prone to flooding. Three kinds of flooding were examined: by peak river discharge, impact by tsunamis and impact by storm surge. The area is already well protected against tsunamis due to the natural shape of the bay Nagoya is situated to. The coastline is well protected against storm surges in the second half of the 20th century. At the river banks however, flood safety is still below the desired level. In the area, risks are relatively high along the Shonai River. Therefore, it has been decided to focus on the threats around the Shonai River. As already described above, there are several locations along the river with safety risks.

In phase 2, several locations and solutions are described to increase the capacity of the river. One major problem is the bottleneck around the Biwajima bridges, where four bridges are narrowing the river. At this location, the desired safety level of a flood discharge occurring once in 200 years is still far away. After discussion with officials of the Shonai River office, it was found that this problem was most urgent. Therefore, it had been chosen to elaborate further on this option in phase 3 and 4.
In phase 3, several options are described to remove the bottleneck. The first option is to replace the bridges with more clearance and larger spans. The second option is to remove the bridges and replace them for tunnels. The third and last option is to construct a bypass along the river, with flow through a tunnel. The Shonai River office is already working on a plan to raise the bridges, thus the first option has been dropped. The second option required large amounts of space for the tunnels. Therefore, it had been decided to work out the third option of creating a bypass. To minimise the impact of such a bypass and its construction on the surrounding area, the decision is made to construct a bored tunnel.

In the fourth and final phase the solution is verified. This is done concerning structural, hydraulic and construction method aspects. All the aspects are found to be possible. In hydraulic aspect, it is found that the required discharge capacity to reach a once in 200 year safety level equals 4250 m3/s. The current discharge capacity is found to be 2850 m3/s. Therefore, the bypass should have a minimal discharge capacity of 1400 m3/s. When using a bored tunnel, it is found that two tunnels with the maximal internal diameter of 16 m should be applied. On top of that, because the concrete surface is to rough in the best circumstances, it was decided to apply an epoxy layer on the surface. Using such a layer, it is found that the total discharge capacity becomes 1490m3/s.
The construction of the tunnel would take 137 weeks to complete. The total costs are estimated to be in the order of ¥60,000,000,000, or 60 billion yen, equivalent to 463 million euro. In comparison, the plan of the river office to replace the bridges would cost ¥68,400,000,000. It can be concluded that this option is a reasonable alternative for the current plan.