Motivated by the ideas of automatic common-midpoint (CMP) stacking without normal-moveout (NMO) correction, hence NMO stretch, and automatizing the velocity model building, we propose a cross-correlation/cross-coherence-based approach. It is a two-step method where the first step is cross-correlation/cross-coherence of zero-offset traces with all other traces in corresponding CMP gathers. This step removes the NMO effect of different hyperbolic events, resulting in CMP gathers with flat events without any stretching effect. Following this, horizontal summation across different CMP gathers is done, resulting in a velocity-free data-driven production of time-domain stacked seismic section. The second step takes advantage of the cross-correlation lags via data-driven k-means cluster analysis to separate lags corresponding to individual hyperbolic events in the CMP gather into distinct clusters. Different norm fittings to lags within individual clusters are evaluated and the lowest residual one automatically selected, resulting in a velocity and zero-offset two-way traveltime time per cluster. These form a base to build an average velocity model for migration and time-to-depth conversion. We demonstrate the efficiency of the proposed method using synthetic and field shear-wave data acquired in southwestern Sweden.@en

Seismic imaging characteristics of a prototype electrically driven, linear synchronous motor-based, vertical-force seismic vibrator ("e-vib") were evaluated at a site in the Netherlands. The system weighs 1.65 t and excites seismic signals with a peak force of 6.7 kN. Data were recorded along two collocated geophone-based nodal and landstreamer microelectromechanical system - MEMS-based sensor 2D seismic profiles. To obtain a broad bandwidth data set, the e-vib operated with a 1-200 Hz linear sweep. Shot gathers of the merged nodal-landstreamer data set indicated good-quality seismic data of a broadband nature. The processed merged data set demonstrates high-resolution reflections of the stratigraphic members from approximately 200 m to 2 km, with visible reflections as deep as 2.5-2.9 km. As a reference, we also processed a legacy 3D microspread data set acquired at the same site with a magnitude stronger (14.1 t, 67.5 kN) hydraulic vibrator. Comparison of our nodal-landstreamer seismic section versus 2D slices extracted from the processed microspread seismic volume suggested similar signal penetration depth and the same key marker horizons seen in both. Analysis of the reaction mass and base-plate accelerometer signals recorded with the e-vib source operating on grass and on asphalt surfaces indicates that the e-vib has low total harmonic distortion. The results obtained indicate that, although relatively small, the e-vib is capable of generating high-quality broadband seismic data.

@en

To evaluate and upscale the feasibility of using exploration tunnels in an operating mine for active-source seismic imaging, a seismic experiment was conducted at the Neves-Corvo mine, in southern Portugal. Four seismic profiles were deployed in exploration drifts approximately 650 m beneath the ground surface, above the world-class Lombador volcanogenic massive sulfide deposit. In addition to the tunnel profiles, two perpendicular surface seismic profiles were deployed above the exploration tunnels. The survey was possible due to a newly developed prototype global positioning system (GPS) time transmitter enabling accurate GPS synchronization of cabled and nodal seismic recorders, below and on the surface. Another innovative acquisition aspect was a 1.65 t broadband, linear synchronous motor (LSM) driven - electric seismic vibrator (e-vib) used as the seismic source along two of the exploration tunnels. We have evaluated the challenges and innovations necessary for active-source tunnel seismic acquisition, characterized by high levels of vibrational noise from the mining activities. In addition, we evaluated the LSM vibrator's signal and overall seismic-data quality in this hard rock mining environment. Our processing results from the tunnel data and 3D reflection imaging of the Lombador deposit below the exploration tunnels were checked for consistency through constant-velocity 3D ray-tracing traveltime forward modeling. For imaging purposes, 3D Kirchhoff prestack depth and poststack time-migration algorithms were used, with both successfully imaging the targeted deposit. The results obtained show that active-source-seismic imaging using subsurface mining infrastructure of operational mines is possible. However, it requires innovative exploration strategies, a broadband seismic source, an accurate GPS-time system capable of transmitting GPS-time hundreds of meters below the surface, and careful processing. The results obtained open up possibilities for similar studies in different mining or tunneling projects. @en

In mineral exploration, new methods to improve the delineation of ore deposits at depth are in demand. For this purpose, increasing the signal-to-noise ratio through suitable data processing is an important requirement. Seismic reflection methods have proven to be useful to image mineral deposits. However, in most hard rock environments, surface waves constitute the most undesirable source-generated or ambient noise in the data that, especially given their typical broadband nature, often mask the events of interest like body-wave reflections and diffractions. In this study, we show the efficacy of a two-step procedure to suppress surface waves in an active-source reflection seismic dataset acquired in the Ludvika mining area of Sweden. First, we use seismic interferometry to estimate the surface-wave energy between receivers, given that they are the most energetic arrivals in the dataset. Second, we adaptively subtract the retrieved surface waves from the original shot gathers, checking the quality of the unveiled reflections. We see that several reflections, judged to be from the mineralization zone, are enhanced and better visualized after this two-step procedure. Our comparison with results from frequency-wavenumber filtering verifies the effectiveness of our scheme, since the presence of linear artefacts is reduced. The results are encouraging, as they open up new possibilities for denoising hard rock seismic data and, in particular, for imaging of deep mineral deposits using seismic reflections. This approach is purely data driven and does not require significant judgment on the dip and frequency content of present surface waves, which often vary from place to place.@en

Exhumation of crust exposes rocks to weathering agents that weaken the rocks’ mechanical strength. Weakened rocks will have lower seismic velocity than intact rocks and can therefore be mapped using seismic methods. However, if the rocks are heavily weathered, they will attenuate controlled-source seismic waves to such a degree that the recorded wavefield would become dominated by ambient noise and/or surface waves. Therefore, we have examined the structure of differential weathering by first-break traveltime tomography over a seismic profile extending approximately 3.5 km and acquired at a mining site in Zambia using explosive sources and a source based on the swept-impact seismic technique (SIST). Seismic interferometry has been tested for the retrieval of supervirtual first arrivals masked by uncorrelated noise. However, use of crosscorrelation in the retrieval process makes the method vulnerable to changes in the source signal (explosives and SIST). Thus, we have developed a crosscoherence-based seismic-interferometry method to tackle this shortcoming. We investigate the method’s efficiency in retrieving first arrivals and, simultaneously, correctly handling variations in the source signal. Our results illustrate the superiority of the crosscoherence- over crosscorrelation-based method for retrieval of the first arrivals, especially in alleviating spurious ringyness and in terms of the signal-to-noise ratio. These benefits are observable in the greater penetration depth and the improved resolution of the tomography sections. The tomographic images indicate isolated bodies of higher velocities, which may be interpreted as fresh rocks embedded into a heavily weathered regolith, providing a conspicuous example of differential weathering. Our study advances the potential of seismic methods for providing better images of the near surface (the critical zone).@en