Many (inter)national standards exist to evaluate the resistance of mortar and concrete to carbonation. When a carbonation coefficient is used for performance comparison of mixtures or service life prediction, the applied boundary conditions during curing, preconditioning and carbonation play a crucial role, specifically when using latent hydraulic or pozzolanic supplementary cementitious materials (SCMs). An extensive interlaboratory test (ILT) with twenty two participating laboratories was set up in the framework of RILEM TC 281-CCC ‘Carbonation of Concrete with SCMs’. The carbonation depths and coefficients determined by following several (inter)national standards for three cement types (CEM I, CEM II/B-V, CEM III/B) both on mortar and concrete scale were statistically compared. The outcomes of this study showed that the carbonation rate based on the carbonation depths after 91 days exposure, compared to 56 days or less exposure duration, best approximates the slope of the linear regression and those 91 days carbonation depths can therefore be considered as a good estimate of the potential resistance to carbonation. All standards evaluated in this study ranked the three cement types in the same order of carbonation resistance. Unfortunately, large variations within and between laboratories complicate to draw clear conclusions regarding the effect of sample pre-conditioning and carbonation exposure conditions on the carbonation performance of the specimens tested. Nevertheless, it was identified that fresh and hardened state properties alone cannot be used to infer carbonation resistance of the mortars or concretes tested. It was also found that sealed curing results in larger carbonation depths compared to water curing. However, when water curing was reduced from 28 to 3 or 7 days, higher carbonation depths compared to sealed curing were observed. This increase is more pronounced for CEM I compared to CEM III mixes. The variation between laboratories is larger than the potential effect of raising the CO₂ concentration from 1 to 4%. Finally, concrete, for which the aggregate-to-cement factor was increased by 1.79 in comparison with mortar, had a carbonation coefficient 1.18 times the one of mortar.

@en

Autonomous repair systems in construction materials have become a promising alternative to current unsustainable and labor-intensive maintenance methods. Biomineralization is a popular route that has been applied to enhance the self-healing capacity of concrete. Various axenic microbial cultures were coupled with protective carriers, and their combination appears to be useful for the development of healing agents for realizing self-healing concrete. The advantageous traits of non-axenic cultures, such as economic feasibility, self-protection, and high specific activity have been neglected so far, and thus the number of studies investigating their performance as healing agents is scarce. Here we present the self-healing performance of a mortar containing a healing agent consisting of non-axenic biogranules with a denitrifying core. Mortar specimens with a defined crack width of 400 μm were used in the experiments and treated with tap water for 28 days. Self-healing was quantified in terms of the crack volume reduction, the thickness of the sealing layer along the crack depth and water permeability under 0.1 bar pressure. Complete visual crack closure was achieved in the bio-based specimens in 28 days, the thickness of the calcite layer was recorded as 10 mm and the healed crack volume was detected as 6%. Upon self-sealing of the specimens, the water permeability decreased by 83%. Overall, non-axenic biogranules with a denitrifying core shows great potential for development of self-healing bioconcrete.@en

The increasing concern for safety and sustainability of structures is calling for the development of smart self-healing materials and preventive repair methods. The appearance of small cracks (<300 µm in width) in concrete is almost unavoidable, not necessarily causing a risk of collapse for the structure, but surely impairing its functionality, accelerating its degradation, and diminishing its service life and sustainability. This review provides the state-of-the-art of recent developments of self-healing concrete, covering autogenous or intrinsic healing of traditional concrete followed by stimulated autogenous healing via use of mineral additives, crystalline admixtures or (superabsorbent) polymers, and subsequently autonomous self-healing mechanisms, i.e. via, application of micro-, macro-, or vascular encapsulated polymers, minerals, or bacteria. The (stimulated) autogenous mechanisms are generally limited to healing crack widths of about 100–150 µm. In contrast, most autonomous self-healing mechanisms can heal cracks of 300 µm, even sometimes up to more than 1 mm, and usually act faster. After explaining the basic concept for each self-healing technique, the most recent advances are collected, explaining the progress and current limitations, to provide insights toward the future developments. This review addresses the research needs required to remove hindrances that limit market penetration of self-healing concrete technologies.@en

The increasing concern for safety and sustainability of structures is calling for the development of smart self-healing materials and preventive repair methods. The appearance of small cracks (<300 µm in width) in concrete is almost unavoidable, not necessarily causing a risk of collapse for the structure, but surely impairing its functionality, accelerating its degradation, and diminishing its service life and sustainability. This review provides the state-of-the-art of recent developments of self-healing concrete, covering autogenous or intrinsic healing of traditional concrete followed by stimulated autogenous healing via use of mineral additives, crystalline admixtures or (superabsorbent) polymers, and subsequently autonomous self-healing mechanisms, i.e. via, application of micro-, macro-, or vascular encapsulated polymers, minerals, or bacteria. The (stimulated) autogenous mechanisms are generally limited to healing crack widths of about 100–150 µm. In contrast, most autonomous self-healing mechanisms can heal cracks of 300 µm, even sometimes up to more than 1 mm, and usually act faster. After explaining the basic concept for each self-healing technique, the most recent advances are collected, explaining the progress and current limitations, to provide insights toward the future developments. This review addresses the research needs required to remove hindrances that limit market penetration of self-healing concrete technologies.@en

At present several methods are available to predict the durability of reinforced concrete structures. In most cases, one dominant deterioration process such as carbonation or chloride penetration is taken into consideration. Experimental results as well as observations in practice show that this is not a realistic and certainly not a conservative approach. In order to test more realistically, RILEM TC 246-TDC, founded in 2011, has developed a method to determine the durability of concrete exposed to the combined action of chloride penetration and mechanical load. In this report, a test method is presented which allows determination of realistic diffusion coefficients for chloride ions in concrete under compressive or tensile stress. Comparative test results from five different laboratories showed that the combination of mechanical and environmental loads may be much more severe than a single environmental load without mechanical loading. Modelling and probabilistic analysis also showed that the obvious synergetic effects cannot be neglected in realistic service life prediction.

@en

At present several methods are available to predict the durability of reinforced concrete structures. In most cases, one dominant deterioration process such as carbonation or chloride penetration is taken into consideration. Experimental results as well as observations in practice show that this is not a realistic and certainly not a conservative approach. In order to test more realistically, RILEM TC 246-TDC, founded in 2011, has developed a method to determine the durability of concrete exposed to the combined action of chloride penetration and mechanical load. In this report, a test method is presented which allows determination of realistic diffusion coefficients for chloride ions in concrete under compressive or tensile stress. Comparative test results from five different laboratories showed that the combination of mechanical and environmental loads may be much more severe than a single environmental load without mechanical loading. Modelling and probabilistic analysis also showed that the obvious synergetic effects cannot be neglected in realistic service life prediction.

@en

This article presents the results of an interlaboratory experimental study performed by 13 international research groups within the framework of the activities of the RILEM Technical Committee 225-SAP “Applications of Superabsorbent Polymers in Concrete Construction”. Two commercially available superabsorbent polymers (SAP) were tested in terms of their influence on the freeze–thaw resistance of ordinary concrete. To test the robustness of the method, all participating laboratories used locally produced materials. Furthermore, following this aim, various accelerated methods were used to estimate the resistance of the concrete to freeze–thaw cycles. The effect of adding SAP was from insignificant to considerably positive in terms of improvement in material performance as determined by reduced mass loss after freeze–thaw cycles; only one participant observed worsening of the material behaviour. At the same time, due to the addition of SAP, a much less pronounced decrease in the dynamic Young’s modulus was observed as a result of freeze–thaw testing without deicing salt.

@en

This article presents the results of an interlaboratory experimental study performed by 13 international research groups within the framework of the activities of the RILEM Technical Committee 225-SAP “Applications of Superabsorbent Polymers in Concrete Construction”. Two commercially available superabsorbent polymers (SAP) were tested in terms of their influence on the freeze–thaw resistance of ordinary concrete. To test the robustness of the method, all participating laboratories used locally produced materials. Furthermore, following this aim, various accelerated methods were used to estimate the resistance of the concrete to freeze–thaw cycles. The effect of adding SAP was from insignificant to considerably positive in terms of improvement in material performance as determined by reduced mass loss after freeze–thaw cycles; only one participant observed worsening of the material behaviour. At the same time, due to the addition of SAP, a much less pronounced decrease in the dynamic Young’s modulus was observed as a result of freeze–thaw testing without deicing salt.

@en

This article presents the results of an interlaboratory experimental study performed by 13 international research groups within the framework of the activities of the RILEM Technical Committee 225-SAP “Applications of Superabsorbent Polymers in Concrete Construction”. Two commercially available superabsorbent polymers (SAP) were tested in terms of their influence on the freeze–thaw resistance of ordinary concrete. To test the robustness of the method, all participating laboratories used locally produced materials. Furthermore, following this aim, various accelerated methods were used to estimate the resistance of the concrete to freeze–thaw cycles. The effect of adding SAP was from insignificant to considerably positive in terms of improvement in material performance as determined by reduced mass loss after freeze–thaw cycles; only one participant observed worsening of the material behaviour. At the same time, due to the addition of SAP, a much less pronounced decrease in the dynamic Young’s modulus was observed as a result of freeze–thaw testing without deicing salt.

@en

This article presents the results of an interlaboratory experimental study performed by 13 international research groups within the framework of the activities of the RILEM Technical Committee 225-SAP “Applications of Superabsorbent Polymers in Concrete Construction”. Two commercially available superabsorbent polymers (SAP) were tested in terms of their influence on the freeze–thaw resistance of ordinary concrete. To test the robustness of the method, all participating laboratories used locally produced materials. Furthermore, following this aim, various accelerated methods were used to estimate the resistance of the concrete to freeze–thaw cycles. The effect of adding SAP was from insignificant to considerably positive in terms of improvement in material performance as determined by reduced mass loss after freeze–thaw cycles; only one participant observed worsening of the material behaviour. At the same time, due to the addition of SAP, a much less pronounced decrease in the dynamic Young’s modulus was observed as a result of freeze–thaw testing without deicing salt.

@en

This article presents the results of an interlaboratory experimental study performed by 13 international research groups within the framework of the activities of the RILEM Technical Committee 225-SAP “Applications of Superabsorbent Polymers in Concrete Construction”. Two commercially available superabsorbent polymers (SAP) were tested in terms of their influence on the freeze–thaw resistance of ordinary concrete. To test the robustness of the method, all participating laboratories used locally produced materials. Furthermore, following this aim, various accelerated methods were used to estimate the resistance of the concrete to freeze–thaw cycles. The effect of adding SAP was from insignificant to considerably positive in terms of improvement in material performance as determined by reduced mass loss after freeze–thaw cycles; only one participant observed worsening of the material behaviour. At the same time, due to the addition of SAP, a much less pronounced decrease in the dynamic Young’s modulus was observed as a result of freeze–thaw testing without deicing salt.

@en

This article presents the results of an interlaboratory experimental study performed by 13 international research groups within the framework of the activities of the RILEM Technical Committee 225-SAP “Applications of Superabsorbent Polymers in Concrete Construction”. Two commercially available superabsorbent polymers (SAP) were tested in terms of their influence on the freeze–thaw resistance of ordinary concrete. To test the robustness of the method, all participating laboratories used locally produced materials. Furthermore, following this aim, various accelerated methods were used to estimate the resistance of the concrete to freeze–thaw cycles. The effect of adding SAP was from insignificant to considerably positive in terms of improvement in material performance as determined by reduced mass loss after freeze–thaw cycles; only one participant observed worsening of the material behaviour. At the same time, due to the addition of SAP, a much less pronounced decrease in the dynamic Young’s modulus was observed as a result of freeze–thaw testing without deicing salt.

@en

This article presents the results of an interlaboratory experimental study performed by 13 international research groups within the framework of the activities of the RILEM Technical Committee 225-SAP “Applications of Superabsorbent Polymers in Concrete Construction”. Two commercially available superabsorbent polymers (SAP) were tested in terms of their influence on the freeze–thaw resistance of ordinary concrete. To test the robustness of the method, all participating laboratories used locally produced materials. Furthermore, following this aim, various accelerated methods were used to estimate the resistance of the concrete to freeze–thaw cycles. The effect of adding SAP was from insignificant to considerably positive in terms of improvement in material performance as determined by reduced mass loss after freeze–thaw cycles; only one participant observed worsening of the material behaviour. At the same time, due to the addition of SAP, a much less pronounced decrease in the dynamic Young’s modulus was observed as a result of freeze–thaw testing without deicing salt.

@en

This article presents the results of an interlaboratory experimental study performed by 13 international research groups within the framework of the activities of the RILEM Technical Committee 225-SAP “Applications of Superabsorbent Polymers in Concrete Construction”. Two commercially available superabsorbent polymers (SAP) were tested in terms of their influence on the freeze–thaw resistance of ordinary concrete. To test the robustness of the method, all participating laboratories used locally produced materials. Furthermore, following this aim, various accelerated methods were used to estimate the resistance of the concrete to freeze–thaw cycles. The effect of adding SAP was from insignificant to considerably positive in terms of improvement in material performance as determined by reduced mass loss after freeze–thaw cycles; only one participant observed worsening of the material behaviour. At the same time, due to the addition of SAP, a much less pronounced decrease in the dynamic Young’s modulus was observed as a result of freeze–thaw testing without deicing salt.

@en

The suitability of using a spore-forming ureolytic strain, Bacillus sphaericus, was evaluated for self-healing of concrete cracks. The main focus was on alkaline tolerance, calcium tolerance, oxygen dependence, and low-temperature adaptability. Experimental results show that B. sphaericus had a good tolerance. It can grow and germinate in a broad range of alkaline pH. The optimal pH range is 7 ∼ 9. High alkaline conditions (pH 10 ∼ 11) slow down but not stop the growth and germination. Oxygen was strictly needed during bacterial growth and germination, but not an essential factor during bacterial urea decomposition. B. sphaericus also had a good Ca tolerance, especially at a high bacterial concentration of 10⁸ cells/mL; no significant influence was observed on bacterial ureolytic activity of the presence of 0.9M Ca²⁺. Furthermore, at a low temperature (10 °C), bacterial spores germinated and revived ureolytic activity with some retardation. However, this retardation can be counteracted by using a higher bacterial concentration and by supplementing yeast extract. It can be concluded that B. sphaericus is a suitable bacterium for application in bacteria-based self-healing concrete.

@en

Superabsorbent polymers (SAPs) have potential to be used as healing agent in self-healing concrete due to their property to attract moisture from the environment and their capacity to promote autogenous healing. A possible drawback, however, is their uptake of mixing water during concrete manufacturing, resulting in an increased volume of macro-pores in the hardened concrete. To limit this drawback, newly developed SAPs with a high swelling and pH-sensitiveness were developed and tested within the FP7 project HEALCON. Evaluation of their self-sealing performance occurred through a water permeability test via water flow, a test method also developed within HEALCON. Three different sizes of the newly developed SAP were compared with a commercial SAP. Swelling tests in cement filtrate solution indicated that the commercial and in-house synthesized SAPs performed quite similar, but the difference between the swelling capacity at pH 9 and pH 13 is more pronounced for the self-synthesized SAPs. Moreover, in comparison to the commercial SAPs, less macro-pores are formed in the cement matrix of mixes with self-synthesized SAPs and the effect on the mechanical properties is lower, but not negligible, when using high amounts of SAPs. Although the immediate sealing effect of cracks in mortar was the highest for the commercial SAPs, the in-house made SAPs with a particle size between 400 and 600 μm performed the best with regard to crack closure (mainly CaCO₃ precipitation) and self-sealing efficiency, after exposing the specimens to 28 wet-dry cycles. Some specimens could even withstand a water pressure of 2 bar.

@en

Superabsorbent polymers (SAPs) have potential to be used as healing agent in self-healing concrete due to their property to attract moisture from the environment and their capacity to promote autogenous healing. A possible drawback, however, is their uptake of mixing water during concrete manufacturing, resulting in an increased volume of macro-pores in the hardened concrete. To limit this drawback, newly developed SAPs with a high swelling and pH-sensitiveness were developed and tested within the FP7 project HEALCON. Evaluation of their self-sealing performance occurred through a water permeability test via water flow, a test method also developed within HEALCON. Three different sizes of the newly developed SAP were compared with a commercial SAP. Swelling tests in cement filtrate solution indicated that the commercial and in-house synthesized SAPs performed quite similar, but the difference between the swelling capacity at pH 9 and pH 13 is more pronounced for the self-synthesized SAPs. Moreover, in comparison to the commercial SAPs, less macro-pores are formed in the cement matrix of mixes with self-synthesized SAPs and the effect on the mechanical properties is lower, but not negligible, when using high amounts of SAPs. Although the immediate sealing effect of cracks in mortar was the highest for the commercial SAPs, the in-house made SAPs with a particle size between 400 and 600 μm performed the best with regard to crack closure (mainly CaCO₃ precipitation) and self-sealing efficiency, after exposing the specimens to 28 wet-dry cycles. Some specimens could even withstand a water pressure of 2 bar.

@en

Superabsorbent polymers (SAPs) have potential to be used as healing agent in self-healing concrete due to their property to attract moisture from the environment and their capacity to promote autogenous healing. A possible drawback, however, is their uptake of mixing water during concrete manufacturing, resulting in an increased volume of macro-pores in the hardened concrete. To limit this drawback, newly developed SAPs with a high swelling and pH-sensitiveness were developed and tested within the FP7 project HEALCON. Evaluation of their self-sealing performance occurred through a water permeability test via water flow, a test method also developed within HEALCON. Three different sizes of the newly developed SAP were compared with a commercial SAP. Swelling tests in cement filtrate solution indicated that the commercial and in-house synthesized SAPs performed quite similar, but the difference between the swelling capacity at pH 9 and pH 13 is more pronounced for the self-synthesized SAPs. Moreover, in comparison to the commercial SAPs, less macro-pores are formed in the cement matrix of mixes with self-synthesized SAPs and the effect on the mechanical properties is lower, but not negligible, when using high amounts of SAPs. Although the immediate sealing effect of cracks in mortar was the highest for the commercial SAPs, the in-house made SAPs with a particle size between 400 and 600 μm performed the best with regard to crack closure (mainly CaCO₃ precipitation) and self-sealing efficiency, after exposing the specimens to 28 wet-dry cycles. Some specimens could even withstand a water pressure of 2 bar.

@en

Self-healing concrete has created a lot of public interest in recent years. Several research groups worldwide are currently working on creating durable and sustainable self-healing concrete structures. HEALCON (the concrete which repairs itself) is a European Union funded project, which focuses on developing cementitious materials with different selfhealing mechanisms. The self-healing mechanisms can either repair the cracks and regain liquid-tightness, bridge the cracks and recover structural performance, or do both. One of the promising materials that have been studied within the project is the bacteria-based selfhealing mortar, which is able to regain liquid tightness after cracking and healing. Within HEALCON an experimental methodology, which comprises of tests for evaluating the ability of the cementitious material to regain liquid-tightness and mechanical properties, has been developed. This study focuses on evaluating the suggested experimental methodology through a round robin test (RRT) among five laboratories within the framework of RILEM/TC 253 MCI (Micro-organisms-Cementitious Materials Interactions), WG4 (Engineered bacteria-based protective systems for cementitious materials) and it concerns only the part that examines the sealing efficiency. The testing sequence includes: - tests for material characterization, - crack introduction on mortar prisms, - healing treatment and - water tightness examination. Specimens with and without bacteria-based self-healing agent were tested. After the completion of the tests the results of the different laboratories were gathered for purposes of comparison. The comparison revealed high scatter in the results of the suggested methodology. Therefore, the current paper gives some recommendations, for improving the tests procedures, which will later be adapted to the second RRT that will follow.@en