Ventilated cavities in the wake of a two-dimensional bluff body are studied experimentally via time-resolved X-ray densitometry. With a systematic variation of flow velocity and gas injection rate, expressed as Froude number ( Fr ) and ventilation coefficient ( Cqs ), four cavities with different closure types are identified. A regime map governed by Fr and Cqs is constructed to estimate flow conditions associated with each cavity closure type. Each closure exhibits a different gas ejection mechanism, which in turn dictates the cavity geometry and the pressure in the cavity. Three-dimensional cavity closure is seen to exist for the supercavities at low Fr . However, closure is nominally two-dimensional for supercavities at higher Fr. At low Cqs, cavity closure is seen to be wake-dominated, while supercavities are seen to have interfacial perturbation near the closure at higher Cqs, irrespective of Fr. With the measured gas fraction, a gas balance analysis is performed to quantify the gas ejection rate at the transitional cavity closure during its formation. For a range of Fr, the transitional cavity closure is seen to be characterised by re-entrant flow, whose intensity depends on the flow inertia, dictating the gas ejection rates. Two different ventilation strategies were employed to systematically investigate the formation and maintenance gas fluxes. The interaction of wake and gas injection is suspected to dominate the cavity formation process and not the maintenance, resulting in ventilation hysteresis. Consequently, the ventilation gas flux required to maintain the supercavity is significantly less than the gas flux required to form the supercavity.

Cavitation, a ubiquitous phenomenon responsible for the sound of knuckles cracking, the erosion-wear of ship propeller blades and targeted drug delivery permeates natural, industrial and biomedical realms. It presents both challenges and opportunities for various applications, hence, a fundamental understanding of cavitation flows is imperative. Cavitation can be broadly classified as natural or ventilated: Natural cavitation occurs when the pressure in the flow drops below the vapour pressure, leading to the formation of vapour bubbles/cavities. Alternately, ventilated cavities are formed by injecting non-condensable gas into the flow. Although fundamentally different, these flows share various underlying physical phenomena. In this dissertation, a commonly occurring, yet complex formof natural cavitation − partial cavitation is examined in combination with ventilated cavities to further our current understanding of cavitation flows....

The bubbly shock-driven partial cavitation in an axisymmetric venturi is studied with time-resolved two-dimensional X-ray densitometry. The bubbly shock waves are characterised using the vapour fraction and pressure changes across it, propagation velocity, and Mach number. The sharp changes in vapour fraction measured with X-ray densitometry, combined with high-frequency dynamic pressure measurements, reveal that the interaction of the pressure wave with the vapour cavity dictates the shedding dynamics. At the lowest cavitation number (σ∼0.47), the condensation shock front is the predominant shedding mechanism. However, as σ increases (σ∼0.78), we observe an upstream travelling pressure discontinuity that changes into a condensation shock as it approaches the venturi throat. This coincides with the increasing strength of the bubbly shock wave as it propagates upstream, manifested by the increasing velocity of the shock front and the pressure rise across it. Consequently, the Mach number of the shock front increases and surpasses the critical value 1, favouring condensation shocks. Further, at higher σ (∼0.84–0.9), both the re-entrant jet and pressure wave can cause cavity detachment. However, at such σ, the pressure wave likely remains subsonic. Hence cavity condensation is not favoured readily. This leads to the re-entrant jet causing the cavity detachment at higher σ. The shock front is accelerated as it propagates upstream through the variable cross-section of the venturi. This enhances its strength, favouring cavity condensation and eventual shedding. These observations explain the existence of shock fronts in an axisymmetric venturi for a large range of σ.

Abstract: The so-called ‘re-entrant jet’ is fundamental to periodic cloud shedding in partial cavitation. However, the exact physical mechanism governing this phenomenon remains ambiguous. The complicated topology of the re-entrant flow renders whole-field, detailed measurement of the re-entrant flow cumbersome. Hence, most studies in the past have derived a physical understanding of this phenomenon from qualitative analyses of the re-entrant jet. Thus, quantitative studies are scarce in the literature. In this work, we present a methodology to experimentally measure the re-entrant flow below the vapour cavity in an axisymmetric venturi. The axisymmetry of the flow geometry is exploited to image tracer particles in the near-wall re-entrant flow. The main objective of employing tomographic imaging and subsequent velocimetry is to resolve the thickness and the velocity of the re-entrant flow. Additionally, phase-averaging conditioned on cavity length sheds light on the temporal evolution of re-entrant flow in a shedding cycle. The measured re-entrant film is as thick as ∼ 1.2 mm for a maximum cavity length of ∼ 0.9 D_t, where D_t is the venturi throat diameter. However, the re-entrant film thickness at higher cavitation number is measured to be about 0.5 mm. Further, the re-entrant flow is seen to attain a maximum velocity up to half the throat velocity as the vapour cavity grows in time and the re-entrant flow thickens. We observe that a complex spatio-temporal evolution of re-entrant flow is involved in the cavity detachment and periodic cloud shedding. Finally, we apply the demonstrated methodology to study the evolution of the near-wall liquid flow, below the vapour cavity in different cavity shedding flow regimes. The role of two main mechanisms responsible for cloud shedding, i.e. (i) the adverse-pressure gradient driven re-entrant jet, and (ii) the bubbly shock wave emanating from the cloud collapse are quantitatively assessed. We observe that the thickness of the re-entrant liquid film with respect to the cavity thickness can influence the cavity shedding behaviour. Further, we show that both the mechanisms could be operating at a given flow condition, with one of them dominating to dictate the cloud shedding behaviour. Graphical abstract: [Figure not available: see fulltext.]

This study focuses on the measurement accuracy of Magnetic Resonance Velocimetry (MRV) in high-speed turbulent flows. One of the most prominent errors in MRV is the displacement error, which describes the misregistration of spatial coordinates and velocity components in moving fluids. Displacement errors are particularly critical for experiments with high flow velocity and high spatial resolution. The degree of displacement error also depends on the sequence structure of the MRV technique. In this study, two MRV sequence types are examined regarding their measurement capabilities in high-speed turbulent flows: a conventional MRV sequence based on the popular “4D FLOW” technique, and a newly developed sequence, named “SYNC SPI”. Compared to conventional MRV, SYNC SPI is designed for high measurement accuracy, and not for imaging speed, which limits its application to statistically stationary flows. Both sequence types are evaluated in a flow experiment with a converging–diverging nozzle. Time-averaged results are presented for velocities up to 12 m/s at the throat. Supported by Particle Imaging Velocimetry, it is shown that SYNC SPI is capable of acquiring accurate velocity data in these highly turbulent flows. In contrast, the data from the conventional MRV sequence exhibits substantial displacement errors with a maximum displacement of 21 mm. The long acquisition time is the main disadvantage of the SYNC SPI sequence. Therefore, it is examined if undersampling and non-linear reconstruction, known as Compressed Sensing, can be utilized to make data acquisition more efficient. In the presented measurements, Compressed Sensing is successfully applied to shorten the acquisition time by up to 70% with almost no reduction in measurement accuracy.