document

Hydrostatic analyses of uprighting processes of a capsized and damaged ship

Pan, Dewei (author), Lin, Chengxin (author), Zhou, Zhaoxin (author), Sun, Yuqinag (author), Sun, Yuhao (author)

journal article 2018

document

Investigation of the Application of adhesively bonded lifting lugs in ship building

Sun, J. (author)

Defects are produced when lifting lugs being welded on ship sections during the building process. The large amount of heat produced in the welding work causes “heat affected zone” in the base metal on sections and destroys painted coatings on the plates; and residual stress decreases the mechanical performance of the steel plates. To eliminate...

master thesis 2017

document

Plasticity under rough surface contact and friction

Sun, F. (author)

The ultimate objective of this work is to gain a better understanding of the plastic behavior of rough metal surfaces under contact loading. Attention in this thesis focuses on the study of single and multiple asperities with micrometer scale dimensions, a scale at which plasticity is known to be size dependent. The asperities have very simple...

doctoral thesis 2016

document

Chaotic Dynamics in Smart Grid and Suppression Scheme via Generalized Fuzzy Hyperbolic Model

Sun, Q. (author), Wang, Y. (author), Yang, J. (author), Qiu, Y. (author), Zhang, H. (author)

This paper presents a method to control chaotic behavior of a typical Smart Grid based on generalized fuzzy hyperbolic model (GFHM). As more and more distributed generations (DG) are incorporated into the Smart Grid, the chaotic behavior occurs increasingly. To verify the behavior, a dynamic model which describes a power system with DG is...

journal article 2014

document

Stochastic hydroelastic analysis of a very large floating structure using pseudo-excitation method

Li, Hai-Tao (author), Wang, Qi-bin (author), Zong, Zhi (author), Sun, Lei (author), Liang, Hui (author)

journal article 2014

document

Differences in abdominal force between conventional and single port laparoscopy

Sun, S. (author), Dankelman, J. (author), Horeman, T. (author)

In laparoendoscopic single-site surgery (LESS), only one single incision is used to introduce all instruments into the abdominal cavity. The introduction of multi-channel single-port devices enabled insertion of laparoscopic instruments and laparoscope through one single entry point instead of multiple entry points in conventional laparoscopic...

conference paper 2013

document

A Hybrid Box Trainer for Training of Technical Skills in Laparoendoscopic Single Site Surgery (LESS)

Sun, S. (author)

The goal of this thesis is to design a hybrid trainer that can quantitatively measure the LESS performance while investigating the difference between LESS and CLS, finally propose a novel objective assessment tools for future research. A force platform is developed, which measures tissue manipulation force in the range of 0-20N with an accuracy...

master thesis 2013

document

Recycling of Aluminum from Fibre Metal Laminates

Zhu, G. (author), Xiao, Y. (author), Yang, Y. (author), Wang, J. (author), Sun, B. (author), Boom, R. (author)

Recycling of aluminum alloy scrap obtained from delaminated fibre metal laminates (FMLs) was studied through high temperature refining in the presence of a salt flux. The aluminum alloy scrap contains approximately mass fraction w(Cu) = 4.4%, w(Mg) = 1.1% and w(Mn) = 0.6% (2024 aluminum alloy). The main objective of this research is to obtain a...

journal article 2012

document

Degradation Behavior of Epoxy Resins in Fibre Metal Laminates Under Thermal Conditions

Zhu, G. (author), Xiao, Y. (author), Yang, Y. (author), Wang, J. (author), Sun, B. (author), Boom, R. (author)

GLARE (glass fibre/epoxy reinforced aluminum laminate) is a member of the fiber metal laminate (FML) family, and is built up of alternating metal and fiber layers. About 500m2 GLARE is employed in each Airbus A380 because of the superior mechanical properties over the monolithic aluminum alloys, such as weight reduction, improved damage...

journal article 2012

document

Hydrodynamic forces on a semi-displacement ship at high speed

Sun, H. (author), Faltinsen, Odd M. (author)

journal article 2012

document

Identification of Models of Industrial Batch Cooling Crystallization system

Sun, X. (author)

master thesis 2011

document

Predictions of porpoising inception for planing vessels

Sun, H. (author)

journal article 2011

document

Dynamic modeling of cable towed body using nodal position finite element method

Sun, F.J. (author)

journal article 2011

document

Hydrodynamic forces on high-speed ships in forced vertical motions

Sun, Hui (author), Faltinsen, Odd M. (author)

conference paper 2011

document

Nonlinear adaptive model predictive control for ship path-following using parametric neighbouring extremal approach

Gao, Lingfeng (author), Ghaemi, Reza (author), Sun, Jing (author)

conference paper 2011

document

Numerical analysis of the effects on a floating structure induced by ship waves

Sun, L. (author)

journal article 2011

document

Dynamic motions of planning vessels in head seas

Sun, H. (author)

journal article 2011

document

Internal heat exchange in a concentric tray Heat Integrated Distillation Column (HIDiC): Experimental validation of predictive models

Sun, A.R. (author)

Experiments with a water/ethanol mixture are performed to determine the internal heat transfer rate of a concentric tray HIDiC and its characteristics. The experimental setup is tested at different process conditions, while measuring intercolumn heat transfer. The process parameters varied are column operating pressure and steam pressure. The...

master thesis 2010

document

Water entry of a bow-flare ship section with roll angle

Sun, H. (author)

journal article 2009

document

Performance prediction of cavitating water-jet propulsors using a viscous/inviscid interactive method

Sun, Hong (author), Spyros, A. (author)

report 2008