Integration Technologies for Smart Catheters

Around 10% of the population will have to go through a catheterization procedure for the treatment of a cardiovascular disease at a certain stage of their lives. During such a procedure, smart catheters will be the "eyes and ears" of the surgeons, significantly improving the diagnosis and treatment. However, there have been very limited...

Mechanotransduction in high aspect ratio nanostructured meta-biomaterials: The role of cell adhesion, contractility, and transcriptional factors

Black Ti (bTi) surfaces comprising high aspect ratio nanopillars exhibit a rare combination of bactericidal and osteogenic properties, framing them as cell-instructive meta-biomaterials. Despite the existing data indicating that bTi surfaces induce osteogenic differentiation in cells, the mechanisms by which this response is regulated are not...

Influence of aspect ratio and pre-compression on force capacity of unreinforced masonry walls in out-of-plane two-way bending

Out-of-plane (OOP) failure of unreinforced masonry (URM) walls in two-way bending was widely observed after natural hazards such as earthquakes. Of various crucial factors influencing the force capacity of URM walls in OOP two-way bending (force capacity being defined as the wall peak force in terms of pressure), the pre-compression and...

Submerged floating tunnel cross-section analysis using a transition turbulence model

Concepts of a submerged floating tunnel (SFT) for novel sea-crossings have been researched in recent years. An SFT tube should be moored afloat by tensioned mooring systems to maintain the tube position under complex hydrodynamic loads. In-line force is amongst the dominant hydrodynamic parameters in the SFT cross-section design and the...

Embedded High-Density Trench Capacitors for Smart Catheters

Our work presents embedded high-density oxide-nitride-oxide (ONO) trench capacitors for power supply decoupling in the next generation of smart catheters. These millimeter-scale smart catheters are using a novel integration platform, Flex-to-Rigid (F2R). In the F2R platform, various functional modules are fabricated or assembled on thin silicon...

The role of the austenite grain size in the martensitic transformation in low carbon steels

There is sufficient experimental evidence to propose that the formation kinetics of athermal martensite directly depends on the austenite grain structure from which the martensite forms. Yet, this dependence is frequently ignored. The present study investigates the role of the prior austenite grain size (PAGS) in the martensitic...

An implicit wetting and drying approach for non-hydrostatic baroclinic flows in high aspect ratio domains

A new approach to modelling free surface flows is developed that enables, for the first time, 3D consistent non-hydrostatic baroclinic physics that wets and drys in the large aspect ratio spatial domains that characterise geophysical systems. This is key in the integration of physical models to permit seamless simulation in a single...

Monolithic 3D Wafer Level Integration: Applied for Smart LED Wafer Level Packaging

Numerical study on the flow characteristics of micro air vehicle wings at low Reynolds numbers

The aerodynamic characteristics around a micro air vehicle wing with an inverse-Zimmerman configuration are numerically investigated by an in-house programmed solver particularly dedicated for aircrafts operating in low Reynolds number regime. The complex three-dimensional aerodynamic performance was investigated in terms of force generation...

DRIE and Bonding Assisted Low Cost MEMS Processing of In-plane HAR Inertial Sensors

We present a simple, flexible and low cost MEMS fabrication process, developed using deep reactive ion etching (DRIE) and wafer bonding technologies, for manufacturing in-plane high aspect ratio (HAR) inertial sensors. Among examples, the design and fabrication results of a two axis inertial device are presented. Fabricated device thickness...

2D InP photonic crystal fabrication process development

We have developed a reliable process to fabricate high quality 2D air-hole and dielectric column InP photonic crystals with a high aspect ratio on a STS production tool using ICP N2+Cl2 plasma. The photonic crystals have a triangular lattice with lattice constant of 400 nm and air-hole and dielectric column radius of 120 nm. Large efforts have...

Deep anisotropic dry etching of silicon microstructures by high-density plasmas

This thesis deals with the dry etching of deep anisotropic microstructures in monocrystalline silicon by high-density plasmas. High aspect ratio trenches are necessary in the fabrication of sensitive inertial devices such as accellerometers and gyroscopes. The etching of silicon in fluorine-based plasmas is isotropic. To obtain anisotropy the...

Die Gestalt von natürlichen Steinen und ihr Fallverhalten in Wasser

Research at IWAWI of TU Berlin focuses on rock placement in coastal engineering and port construction. During research work it was found that objective and descriptive shape classification of rocks was needed. The introduced method utilizes three independent parameters: size referred to by volume, shape according to Zingg and roundness according...

Supersonic wind tunnel tests of eleven small aspect-ratio wings

The lift, drag and pitching moment characteristics of eleven small aspect-ratio half-wing models mounted on a reflection plate were determined in the range of Mach numbers fom 1.4 to 2.5 in the N.A.E. 10-inch supersonlc tunnel. Eight of the models were of the cropped delta type while the remainlng three had a cropped arrow plan form. Primarily,...