- document
-
Effect of temperature on the healing capacity and mechanical properties of Ti2AlC MAX phase ceramicsSuh, Minji (author), Lee, Dong Heon (author), Sloof, W.G. (author), Lee, Kee Sung (author)In this study, the self-healing capacity of Titanium Aluminum Carbide (Ti<sub>2</sub>AlC, MAX phase) was investigated. Bulk coin samples were fabricated to evaluate the self-healing capacity at different temperatures (1000, 1200, and 1400°C). The extensive self-healing capacity of Ti<sub>2</sub>AlC was confirmed on larger quasiplastic damage ...journal article 2024
- document
-
Xie, Weihang (author), Deng, Zeyu (author), Liu, Zhengyu (author), Famprikis, T. (author), Butler, Keith T. (author), Canepa, Pieremanuele (author)Extended defects, including exposed surfaces and grain boundaries (GBs), are critical to the properties of polycrystalline solid electrolytes in all-solid-state batteries (ASSBs). These defects can alter the mechanical and electronic properties of solid electrolytes, with direct manifestations in the performance of ASSBs. Here, by building a...journal article 2024
- document
-
Andrade, D. G. (author), Tankova, T. (author), Zhu, C. (author), Branco, R. (author), da Silva, L. Simões (author), Rodrigues, D. M. (author)The use of 3D printed stainless steel requires a deep knowledge of its mechanical properties. This paper presents material characterisation of 316LSi austenitic stainless-steel coupons manufactured by CMT-WAAM, considering different deposition directions. The specimens were tested according to ISO 6892-1, the fractures surfaces were examined...journal article 2024
- document
-
Chen, B. (author), Perumal, Priyadharshini (author), Aghabeyk, F. (author), Adediran, Adeolu (author), Illikainen, Mirja (author), Ye, G. (author)The pursuit of low-carbon binders as alternatives to Portland cement has sparked interest in developing alkali-activated materials (AAM).<sup>1</sup> Using municipal solid waste incineration (MSWI) bottom ash as precursor for AAM has attracted increasing attention as it offers a sustainable, resource-efficient solution to mitigate the...review 2024
- document
-
Wang, H. (author), Tao, Jie (author), Wu, Zhangyu (author), Weiland, K.M. (author), Wang, Zuankai (author), Masania, K. (author), Wang, B. (author)Organic polymer-based composite materials with favorable mechanical performance and functionalities are keystones to various modern industries; however, the environmental pollution stemming from their processing poses a great challenge. In this study, by finding an autonomous phase separating ability of fungal mycelium, a new material...journal article 2024
- document
-
Li, Jiayu (author), Accardo, A. (author), Liu, Shutian (author)Micro/nanoscale additive manufacturing provides a powerful tool for advanced materials and structures with complex and precise features. For instance, the feature resolution of two-photon polymerization (2PP) can reach 200 nm. At this scale, materials properties can change, and the influence of the size effect cannot be ignored. Therefore, it...journal article 2024
- document
-
Felicita, M.P. (author), Pagella, G. (author), Ravenshorst, G.J.P. (author), Mirra, M. (author), van de Kuilen, J.W.G. (author)This case study explores the utilization of distributed fiber optic sensors (DFOS) in wooden foundation piles, for assessing and monitoring the stress distribution along their length. Three spruce and three pine foundation piles instrumented with DFOS were driven into the soil in a testing field in Amsterdam and axially loaded in compression....journal article 2024
- document
-
Martin Saint-Laurence, P.M. (author), Aguilar, C. (author), Cabrera, J. M. (author)Refractory high-entropy alloys (RHEAs) are promising candidates for those applications requiring of strong materials at high temperatures with elevated thermal stability and excellent oxidation, irradiation, and corrosion resistance. Particularly, RHEAs synthesized using mechanical alloying (MA) followed by spark plasma sintering (SPS) has...journal article 2024
- document
-
Dong, J. (author)The treatment of largy bone defect remains challenging in clinics. All the clinically available bone grafts have their own limitations and are not ideal for the treatment. Therefore, developing a new generation of suitable bone substitutes is urgently needed. In the recent years, porous magnesium (Mg) has been extensively studied for orthopedic...doctoral thesis 2023
- document
-
RAMOS, STEPHANIE (author)Tensioned membrane structures are increasingly in demand, because of their ability to cover large spaces with minimum use of material. The material’s mechanical properties play a key role in the design of such structures. The shear behaviour is one of the main influential properties of woven textiles during complex deformations, such as the ones...master thesis 2023
- document
-
Lantsoght, E.O.L. (author)One of the barriers to implementation of steel fiber reinforced concrete (SFRC) into structural applications is the lack of understanding of the shear behaviour of SFRC members. This paper proposes a theoretical model for the shear capacity of SFRC members with mild steel reinforcement based on the shear-carrying mechanisms and sectional...journal article 2023
- document
-
Flessati, L. (author), Vecchia, Gabriele Della (author), Musso, Guido (author)Cement-bentonite cut-off walls are commonly employed in geoenvironmental applications to limit ground water flow and pollutant transport. The wide diffusion of this artificial material in the current practice is not only due to its low permeability, but also to its simplicity of use. In this paper, experimental evidences about the role of...journal article 2023
- document
-
Xu, Y. (author), Šavija, B. (author)Auxetic cementitious composites (ACCs) with improved mechanical properties are created, by casting 3D printed polymeric auxetic reinforcement structures inside cementitious mortar. Four types of ACCs incorporating reinforcement with different auxetic mechanisms were prepared: “re-entrant” (RE), “rotating-square” (RS), “chiral” (CR) and ...journal article 2023
- document
-
van Overmeir, A.L. (author), Šavija, B. (author), Bos, Freek P. (author), Schlangen, E. (author)Several studies have shown the potential of strain-hardening cementitious composites (SHCC) as a self-reinforcing printable mortar. However, papers published on the development of three-dimensional printable SHCC (3DP-SHCC) often report a discrepancy between the mechanical properties of the cast and printed specimens. This paper evaluates the...journal article 2023
- document
-
Li, Yageng (author), Shi, Yixuan (author), Lu, Yuchen (author), Li, Xuan (author), Zhou, J. (author), Zadpoor, A.A. (author), Wang, Luning (author)With the advancement of additive manufacturing (AM), customized vascular stents can now be fabricated to fit the curvatures and sizes of a narrowed or blocked blood vessel, thereby reducing the possibility of thrombosis and restenosis. More importantly, AM enables the design and fabrication of complex and functional stent unit cells that...review 2023
- document
-
Saeidi, Omid (author), Rahimi Dalkhani, A. (author)A geomechanics program for wellbore stability analysis has been developed consisting of two modules: an analytical-based solution and a numerical-based solution. In the first part, input data are imported, including petrophysical well logs, pressure data, formation well tops, and a well path. Lithology intervals are set with proper prediction...journal article 2023
- document
-
Hedayati, R. (author), Stulova, Victoria (author)Due to payload weight limitations and human vulnerability to harsh space conditions, it is preferable that the potential landing location for humans has an already constructed habitat preferably made from in situ materials. Therefore, the prospect of utilizing a readily available Martian material, such as regolith, in an easily programmable...journal article 2023
- document
-
Kumar Ashish, Prabin (author), Sreeram, Anand (author), Xu, Xiong (author), Chandrasekar, Pavan (author), Jagadeesh, A. (author), Adwani, Dheeraj (author), Kumar Padhan, Rabindra (author)The widespread production and consumption of plastics is a pressing global issue that requires multifaceted approaches and solutions. In terms of recycling, one of the ways to repurpose waste plastics in the construction industry would be to utilize them for asphalt pavement-related applications. Although this approach can potentially provide...review 2023
- document
-
Liang, M. (author), Zhang, Y. (author), He, S. (author), Chen, Y. (author), Schlangen, E. (author), Šavija, B. (author)This study investigated the evolution process of high-volume slag cement (HVSC) paste from a chemo-mechanical standpoint. HVSC specimens with a 70 w.t. % slag replacement rate were studied at various ages. Evolution of phase assemblage, microstructure development, and micromechanical properties were analyzed using TGA/XRD/MIP/SEM-EDS and nano...journal article 2023
- document
-
van Overmeir, A.L. (author), Šavija, B. (author), Bos, F. P. (author), Schlangen, E. (author)With the introduction of 3D concrete printing, research started on how to include reinforcement in 3D printed structures. Initial studies on the implementation of strain hardening cementitious composites (SHCC) as self-reinforcing printable mortars have shown promising results. The development of this new type of SHCC comes with additional...journal article 2023