Autogenous deformation-induced stress evolution in cementitious materials considering viscoelastic properties: A review of experiments and models

Early-age cracking risk induced by autogenous deformation is high for cementitious materials of low water-binder ratios. The autogenous deformation, viscoelastic properties, and stress evolution are three important factors for understanding and quantifying the early-age cracking risk. This paper systematically reviewed the experimental and...

Lattice modelling of early-age creep of 3D printed segments with the consideration of stress history

We propose a new numerical method to analyze the early-age creep of 3D printed segments with the consideration of stress history. The integral creep strain evaluation formula is first expressed in a summation form using superposition principle. The experimentally derived creep compliance surface is then employed to calculate the creep strain...

Distribution of porosity surrounding a microfiber in cement paste

This study investigates the microstructural changes of cement paste due to the inclusion of polymeric microfiber at different water-to-cement (w/c) ratios. A procedure to quantify the porosity of epoxy impregnated interfacial transition zone (ITZ) is also presented. Results show that the microstructures of the ITZ beneath and above a...

Improving structural build-up of limestone-calcined clay-cement pastes by using inorganic additives

In 3D concrete printing, fast structuration is a prerequisite for ideal buildability. This paper aims to study the impact of inorganic additives, i.e., CaCl₂ and gypsum, on structural build-up and very early-age hydration of limestone-calcined clay-cement (LC3) pastes within the first 70–80 min. Results show that, increasing the...

Ultra-thin Strain Hardening Cementitious Composite (SHCC) layer in reinforced concrete cover zone for crack width control

In the current study, experiments and numerical simulations were carried out to investigate the cracking behavior of reinforced concrete beams consisting of a very thin layer (i.e., 1 cm in thickness) of SHCC in the concrete cover, tension zone. A novel type of SHCC/concrete interface that features a weakened chemical adhesion but an enhanced...

On the chemo-mechanical evolution process of high-volume slag cement paste

This study investigated the evolution process of high-volume slag cement (HVSC) paste from a chemo-mechanical standpoint. HVSC specimens with a 70 w.t. % slag replacement rate were studied at various ages. Evolution of phase assemblage, microstructure development, and micromechanical properties were analyzed using TGA/XRD/MIP/SEM-EDS and nano...

Autogenous deformation induced- stress evolution in high-volume GGBFS concrete: Macro-scale behavior and micro-scale origin

This study aims to experimentally investigate the autogenous deformation and the stress evolution in restrained high-volume ground granulated blast furnace slag (GGBFS) concrete. The Temperature Stress Testing Machine (TSTM) and Autogenous Deformation Testing Machine (ADTM) were used to study the macro-scale autogenous deformation and stress...

Rheology control of limestone calcined clay cement pastes by modifying the content of fine-grained metakaolin

Limestone-calcined clay-cement (LC3), as one of the most promising sustainable cements, has been under development over the past decade. However, many uncertainties remain regarding its rheological behaviors, such as the metakaolin content of calcined clay. This study aims to investigate the effect of increasing the content of fine-grained...

A New Method to Quantitatively Characterize the Porosity of Fiber/Matrix Interfacial Transition Zone (ITZ) via Longitudinal Cross-Sections

The properties of the interfacial transition zone (ITZ) between microfiber and cement-based matrix are of primary significance for the overall behavior of strain hardening cementitious composites (SHCCs). However, due to the relatively small diameter of polymeric microfibers (e.g., PVA fiber), it is technically difficult to obtain...

Predicting micromechanical properties of cement paste from backscattered electron (BSE) images by computer vision

This paper employs computer vision techniques to predict the micromechanical properties (i.e., elastic modulus and hardness) of cement paste based on an input of Backscattered Electron (BSE) images. A dataset comprising 40,000 nanoindentation tests and 40,000 BSE micrographs was built by express nanoindentation test and Scanning Electron...

Predicting early-age stress evolution in restrained concrete by thermo-chemo-mechanical model and active ensemble learning

Early-age stress (EAS) is an important index for evaluating the early-age cracking risk of concrete. This paper encompasses a thermo-chemo-mechanical (TCM) model and active ensemble learning (AEL) for predicting the EAS evolution. The TCM model provides the data for the AEL model. First, based on Fourier's law, Arrhenius’ equation, and rate...

Stress evolution in restrained GGBFS concrete due to autogenous deformation: bayesian optimization of aging creep

Stress evolution of restrained concrete is a significant direct index in early-age cracking (EAC) analysis of concrete. This study presents experiments and numerical modelling of the early-age stress evolution of Ground granulated blast furnace slag (GGBFS) concrete, considering the development of autogenous deformation and creep. Temperature...