ZC
Zhaowei Chen
info
Please Note
<p>This page displays the records of the person named above and is not linked to a unique person identifier. This record may need to be merged to a profile.</p>
3 records found
1
To maximize the use of urban land, many cities have built buildings above metro depots. However, the low-frequency vibration caused by metro operation affects the lives of surrounding residents, which seriously restricts the further development of over-track buildings. To study this problem, Firstly, the vibration of the metro depot and surrounding sensitive areas are tested on a large actual metro depot in Southwest China, and the rail, sleeper/support column, bearing column, and cover plate are mainly tested. Then, considering nonlinear factors such as mechanical properties of building materials, soil layering characteristics, and artificial viscoelastic boundary, the numerical coupled model of the train-track-depot-building is established, and the simulation data are compared with the test data to verify the accuracy of the numerical model. Finally, the impact of metro operation on the over-track buildings is evaluated. Results show that for the over-track buildings concerned in this paper, the floor vibration near the rail is the strongest, the main vibration frequency of the office building is concentrated in 10–20 Hz, and the maximum Z vibration level (VLzmax) of the office building is 52.02 dB. The main vibration frequency of the residential building is similar to that of the office building, and the superposition of floor vibration energy causes the vibration of the mid-span point to be larger than the vibration of the corner point and the side wall point. The vibration wave of lower floors mainly propagates through the bearing column, and the vibration of the parking garage is larger than other buildings. The research results can provide a reference for the vibration control and design of over-track buildings above the metro depot.
...
To maximize the use of urban land, many cities have built buildings above metro depots. However, the low-frequency vibration caused by metro operation affects the lives of surrounding residents, which seriously restricts the further development of over-track buildings. To study this problem, Firstly, the vibration of the metro depot and surrounding sensitive areas are tested on a large actual metro depot in Southwest China, and the rail, sleeper/support column, bearing column, and cover plate are mainly tested. Then, considering nonlinear factors such as mechanical properties of building materials, soil layering characteristics, and artificial viscoelastic boundary, the numerical coupled model of the train-track-depot-building is established, and the simulation data are compared with the test data to verify the accuracy of the numerical model. Finally, the impact of metro operation on the over-track buildings is evaluated. Results show that for the over-track buildings concerned in this paper, the floor vibration near the rail is the strongest, the main vibration frequency of the office building is concentrated in 10–20 Hz, and the maximum Z vibration level (VLzmax) of the office building is 52.02 dB. The main vibration frequency of the residential building is similar to that of the office building, and the superposition of floor vibration energy causes the vibration of the mid-span point to be larger than the vibration of the corner point and the side wall point. The vibration wave of lower floors mainly propagates through the bearing column, and the vibration of the parking garage is larger than other buildings. The research results can provide a reference for the vibration control and design of over-track buildings above the metro depot.
Hydraulic fracturing operation as an effective enhancing coalbed gas production method is widely used in ultra-low permeability coal seam. However, complex geo-stresses and high heterogeneity between natural cleats structure lead to difficulty predicting hydraulic fracture patterns. Fracture evolution behavior for fracturing operation in coal seams requires a better understanding. In this study, a 2D model of hydraulic fracture propagation was built based on the cohesive zone model of finite element method. The effect of orthogonal cleat system, in-situ stress, dig angle and construction parameters on fracture geometries were main investigated. The main conclusions were as follows: (1) According to the interaction types between hydraulic fracture and cleat system, ladder-shaped fracture and H-shaped fracture geometry was summarized. The difference between them was whether there were continuous and small pressure fluctuation stages. (2) When the horizontal stress difference coefficient was lower and larger than 3/12, fracture geometry was prone to present Η shape and ladder shape respectively. Besides, the dimensionless fracture length and the dimensionless fracture extension aspect ratio of fracture were increasing with larger horizontal stress difference coefficient. (3) The favorable condition for fracture extension was that the dig angle was 45°. Hydraulic fracture tended to propagate along face cleats direction. (4) Larger fracture fluid displacement was beneficial to form more balanced hydraulic fracture geometry and promote large extension scale. As fracture fluid viscosity increased, the fracture geometries transformed from ladder shape to H shape.
...
Hydraulic fracturing operation as an effective enhancing coalbed gas production method is widely used in ultra-low permeability coal seam. However, complex geo-stresses and high heterogeneity between natural cleats structure lead to difficulty predicting hydraulic fracture patterns. Fracture evolution behavior for fracturing operation in coal seams requires a better understanding. In this study, a 2D model of hydraulic fracture propagation was built based on the cohesive zone model of finite element method. The effect of orthogonal cleat system, in-situ stress, dig angle and construction parameters on fracture geometries were main investigated. The main conclusions were as follows: (1) According to the interaction types between hydraulic fracture and cleat system, ladder-shaped fracture and H-shaped fracture geometry was summarized. The difference between them was whether there were continuous and small pressure fluctuation stages. (2) When the horizontal stress difference coefficient was lower and larger than 3/12, fracture geometry was prone to present Η shape and ladder shape respectively. Besides, the dimensionless fracture length and the dimensionless fracture extension aspect ratio of fracture were increasing with larger horizontal stress difference coefficient. (3) The favorable condition for fracture extension was that the dig angle was 45°. Hydraulic fracture tended to propagate along face cleats direction. (4) Larger fracture fluid displacement was beneficial to form more balanced hydraulic fracture geometry and promote large extension scale. As fracture fluid viscosity increased, the fracture geometries transformed from ladder shape to H shape.
The dynamic performance of the railway vehicles and the guiding tracks is mainly governed by the wheel-rail interactions, particularly in cases of track irregularities. In this work, a united model was developed to investigate the track portions subject to violent wheel/rail forces triggered by track irregularities at middle-low frequencies. In the modeling procedures, a time-frequency unification method combining wavelet transform and Wigner-Ville distribution for characterizing time-frequency characteristics of track irregularities and a three-dimensional nonlinear model for describing vehicle-track interaction signatures were developed and coupled, based on which the method for predicting track portions subject to deteriorated wheel/rail forces was proposed. The theoretical models developed in this paper were comprehensively validated by numerical investigations. The significance of this present study mainly lies on offering a new path to establish correlation and realize mutual prediction between track irregularity and railway system dynamics.
...
The dynamic performance of the railway vehicles and the guiding tracks is mainly governed by the wheel-rail interactions, particularly in cases of track irregularities. In this work, a united model was developed to investigate the track portions subject to violent wheel/rail forces triggered by track irregularities at middle-low frequencies. In the modeling procedures, a time-frequency unification method combining wavelet transform and Wigner-Ville distribution for characterizing time-frequency characteristics of track irregularities and a three-dimensional nonlinear model for describing vehicle-track interaction signatures were developed and coupled, based on which the method for predicting track portions subject to deteriorated wheel/rail forces was proposed. The theoretical models developed in this paper were comprehensively validated by numerical investigations. The significance of this present study mainly lies on offering a new path to establish correlation and realize mutual prediction between track irregularity and railway system dynamics.