Measuring quantitatively the nanoparticle dispersion of a composite material requires more than choosing a particular parameter and determining its correspondence to good and bad dispersion. It additionally requires anticipation of the measure's behaviour towards imperfect experimental data, such as that which can be obtained from a limited number of samples. It should be recognised that different samples from a common parent population can give statistically different responses due to sample variation alone and a measure of the likelihood of this occurring allows a decision on the dispersion to be made. It is also important to factor into the analysis the quality of the data in the micrograph with it: (a) being incomplete because some of the particles present in the micrograph are indistinguishable or go unseen; (b) including additional responses which are false. With the use of our preferred method, this article investigates the effects on the measured dispersion quality of nanoparticles of the micrograph's magnification settings, the role of the fraction of nanoparticles visible and the number of micrographs used. It is demonstrated that the best choice of magnification, which gives the clearest indication of dispersion type, is dependent on the type of nanoparticle structure present. Furthermore, it is found that the measured dispersion can be modified by particle loss, through the limitations of micrograph construction, and material/microscope imperfections such as cut marks and optical aberrations which could lead to the wrong conclusions being drawn. The article finishes by showing the versatility of the dispersion measure by characterising various different spatial features.@en

The present paper considers the general mechanical, fracture and cyclic-fatigue properties of four different epoxy polymers containing various concentrations of well-dispersed silica nanoparticles. Firstly, it was found that, for any given epoxy polymer, their Youngs modulus steadily increased as the volume fraction, vf, of the silica nanoparticles was increased. Modelling studies showed that the measured moduli of the different silica-nanoparticle filled epoxy-polymers lay between upper-bound values set by the Halpin-Tsai and the Nielsen no-slip models, and lower-bound values set by the Nielsen slip model; with the last model being the more accurate at relatively high values of vf. Secondly, the presence of silica nanoparticles always led to an increase in the toughness of the epoxy polymer. However, to what extent a given epoxy polymer could be so toughened was related to structure/property relationships which were governed by (a) the values of glass transition temperature, Tg, and molecular weight, M c, between cross-links of the epoxy polymer, and (b) the adhesion acting at the silica-nanoparticle/epoxy-polymer interface. Thirdly, the two toughening mechanisms which were operative in the epoxy polymers containing silica nanoparticles were identified to be (a) localised shear-bands initiated by the stress concentrations around the periphery of the silica nanoparticles, and (b) debonding of the silica nanoparticles followed by subsequent plastic void-growth of the epoxy polymer. Fourthly, for one formulation the cyclic-fatigue properties have been studied and a significant improvement was found to arise from the addition of the silica nanoparticles. Finally, the toughening mechanisms have been quantitatively modelled and there was good agreement between the experimentally measured values and the predicted values of the fracture energy, Gc, for all the epoxy polymers modified by the presence of silica nanoparticles. The modelling studies have emphasised the important roles of the stress versus strain behaviour of the epoxy polymer and the silicananoparticle/ epoxy-polymer interfacial adhesion in influencing the extent of the two toughening mechanisms, and hence the overall fracture energy, Gc, of the nanoparticle-filled polymers.@en

The present paper investigates the effect of adding silica nanoparticles to an anhydride-cured epoxy polymer. The formation of 'hybrid' epoxy polymers, containing both silica nanoparticles and carboxyl-Terminated butadiene-Acrylonitrile (CTBNrubber microparticles, is also discussed. The structure/property relationships are considered, with an emphasis on the toughness and the toughening mechanisms. The present work also extends an existing model to predict the toughening effect of the nanoparticles in a thermoset polymer. There was excellent agreement between the predictions and the experimental data for the epoxy containing the silica nanoparticles.@en

The present paper considers the mechanical and fracture properties of four different epoxy polymers containing 0, 10 and 20wt.% of well-dispersed silica nanoparticles. Firstly, it was found that, for any given epoxy polymer, their Young's modulus steadily increased as the volume fraction, vf, of the silica nanoparticles was increased. Modelling studies showed that the measured moduli of the different silica-nanoparticle filled epoxy polymers lay between upper-bound values set by the Halpin-Tsai and the Nielsen 'no-slip' models, and lower-bound values set by the Nielsen 'slip' model; with the last model being the more accurate at relatively high values of vf. Secondly, the presence of silica nanoparticles always led to an increase in the toughness of the epoxy polymer. However, to what extent a given epoxy polymer could be so toughened was related to structure/property relationships which were governed by (a) the values of glass transition temperature, Tg, and molecular weight, Mc, between cross-links of the epoxy polymer, and (b) the adhesion acting at the silica nanoparticle/epoxy-polymer interface. Thirdly, the two toughening mechanisms which were operative in all the epoxy polymers containing silica nanoparticles were identified to be (a) localised shear bands initiated by the stress concentrations around the periphery of the silica nanoparticles, and (b) debonding of the silica nanoparticles followed by subsequent plastic void growth of the epoxy polymer. Finally, the toughening mechanisms have been quantitatively modelled and there was good agreement between the experimentally-measured values and the predicted values of the fracture energy, Gc, for all the epoxy polymers modified by the presence of silica nanoparticles. The modelling studies have emphasised the important roles of the stress versus strain behaviour of the epoxy polymer and the silica nanoparticle/epoxy-polymer interfacial adhesion in influencing the extent of the two toughening mechanisms, and hence the overall fracture energy, Gc, of the nanoparticle-filled polymers.@en

Enterovirus A71 (EV-A71) is an important nonpolio enterovirus that causes severe neurological complications. In 1998, Taiwan experienced an EV-A71 outbreak that caused 78 deaths. Since then, periodic epidemics of EV-A71 associated with newly emerging strains have occurred. Several of these strains are known to be recombinant; however, how these strains arose within such a short period of time remains unknown. Here, we sequenced 64 full-length genomes from clinical isolates collected from 2005 to 2016 and incorporated all 91 Taiwanese genomes downloaded from the Virus Pathogen Resource to extensively analyze EV-A71 recombination in Taiwan. We found that the B3 subgenotype was a potential recombinant parent of the EV-A71 C2-like and C4 strains by intratypic recombination. Such B3-similar regions were also found in many cocirculating coxsackieviruses belonging to Enterovirus A species (EV-A) through a series of intertypic recombinations. Therefore, locally enriched outbreaks of cocirculating viruses from different genotypes/serotypes may facilitate recombination. Most recombination breakpoints we found had nonrandom distributions and were located within the region spanning from the boundary of P1 (structural gene) and P2 (nonstructural) to the cis-Acting replication element at P2, indicating that specific genome reassembly of structural and nonstructural genes may be subject to natural selection. Through intensive recombination, 11 EV-A71-like signatures (including one in 3A, two in 3C, and eight in 3D) were found to be present in a variety of recently cocirculating EV-A viruses worldwide, suggesting that these viruses may be targets for wide-spectrum antiviral development.@en

The present paper investigates the effect of adding silica nanoparticles to an anhydride-cured epoxy polymer in bulk and when used as the matrix of carbon- and glass-fibre reinforced composites. The formation of 'hybrid' epoxy polymers, containing both silica nanoparticles and carboxyl-terminated butadiene-acrylonitrile (CTBN) rubber microparticles, is also discussed. The structure/property relationships are considered, with an emphasis on the toughness and the toughening mechanisms. The fracture energy of the bulk epoxy polymer was increased from 77 to 212 J/m2 by the presence of 20 wt% of silica nanoparticles. The observed toughening mechanisms that were operative were (a) plastic shear-yield bands, and (b) debonding of the matrix from the silica nanoparticles, followed by plastic void-growth of the epoxy. The largest increases in toughness observed were for the 'hybrid' materials. Here a maximum fracture energy of 965 J/m2 was measured for a 'hybrid' epoxy polymer containing 9 wt% and 15 wt% of the rubber microparticles and silica nanoparticles, respectively. Most noteworthy was the observation that these increases in the toughness of the bulk polymers were found to be transferred to the fibre composites. Indeed, the interlaminar fracture energies for the fibre-composite materials were increased even further by a fibre-bridging toughening mechanism. The present work also extends an existing model to predict the toughening effect of the nanoparticles in a thermoset polymer. There was excellent agreement between the predictions and the experimental data for the epoxy containing the silica nanoparticles, and for epoxy polymers containing micrometre-sized glass particles. The latter, relatively large, glass particles were investigated to establish whether a 'nano-effect', with respect to increasing the toughness of the epoxy bulk polymers, did indeed exist.@en