The CR/SBS composite-modified asphalt (CR/SBS-CMA) is recognized for its excellent rutting and fatigue resistance, but with poor workability. Sasobit has been introduced as an additive to improve the workability of CR/SBS-CMA. This study aims to investigate the effects of Sasobit content on the storage stability and rheological properties of CR/SBS-CMA. The Brookfield viscosity tests were used to measure the viscosity of samples. The Fourier transform infrared spectroscopy (FTIR) tests were conducted to study the modification mechanism. The cigar tube and fluorescence microscopy (FM) tests were employed to study the storage stability of samples. The penetration, softening point, and ductility of samples were assessed. The rheological behaviors of samples were assessed through dynamic shear rheometer (DSR) tests and bending beam rheometer (BBR) tests. The test results indicate that Sasobit can effectively reduce the viscosity of CR/SBS-CMA. Sasobit can also improve the rutting resistance, fatigue resistance, and storage stability of CR/SBS-CMA. However, Sasobit negatively affects the low-temperature performance of CR/SBS-CMA, so its content should be lower than 3 % when applied in areas with low temperatures. This study will contribute to the reduction of energy consumption and greenhouse gas emissions during the construction of CR/SBS-CMA pavement.

This study systematically investigated the potential of waste carbon fibers (WCFs) as a sustainable solution in enhancing the multiple induction heating healing of asphalt mixture, thereby tackling two major concerns: the environmental impact of WCFs and the durability of asphalt pavement. Firstly, four groups of asphalt binder samples with different WCFs contents were prepared. The viscosity and workability of WCFs modified asphalt binder were analyzed. Next, asphalt mixture containing 2% steel fibers was prepared at the optimal WCFs content, while control groups without WCFs were prepared with 2% and 4% steel fibers content. A comprehensive study was conducted on the induction heating rate, effective heating depth and surface temperature cooling rules of the asphalt mixture. Finally, by conducting multiple “fracture-healing” tests, the influence of WCFs on the healing efficiency of asphalt mixture was analyzed. The results revealed that WCFs increased the viscosity of the virgin asphalt, but excessive WCFs content hindered the workability. The optimal WCFs content was determined to be 1% (by weight of asphalt binder). WCFs enhanced the thermal conductivity of the asphalt mixture, accelerating heating and improving vertical heat transfer while reducing surface temperature decline. During multiple “fracture -healing” processes, the inclusion of WCFs enhanced the mechanical strength of the asphalt mixture, improved its healing efficiency, and increased the number of healings. Even after five cycles, the specimen with the most damage still showed a fracture energy recovery rate (FERR) of over 30%. In conclusion, WCFs significantly enhanced the multiple induction heating healing efficiency of the asphalt mixture.

Terminal blended rubberized asphalt binder (TB) technology, which blends crumb tire rubber (CR) with asphalt under high interaction conditions, offers a promising waste tire recycling solution for pavement construction. By precisely controlling the degradation progress of CR, it is possible to prepare TB with specific property requirements. However, the degradation progress of CR and its impact on TB property during the TB preparation process remain ambiguous. This hinders the potential for efficient preparation of TB with specific property requirements. This study aims to understand the degradation progress of TB by analyzing binders, soluble fractions, and insoluble fractions obtained at various interaction durations. Microscopic analysis characterizes the chemical composition, morphology, and molecular weight distribution of insoluble and soluble fractions, while macroscopic analysis evaluates the solubility, viscosity, compatibility, and mechanical properties of binders. The results reveal that the degradation of CR during the preparation of TB consists of a desulfurization reaction, depolymerization reaction, and release behavior (carbon black and fillers). Depending on the degradation progress of CR, the interaction process can be classified into three stages: initial (desulfurization reaction dominant stage), middle (depolymerization reaction dominant stage), and last (release behavior dominant stage). The desulfurization reaction of CR is almost completed in the initial stage. The depolymerization reactions and release behavior occur throughout the process. The most pronounced depolymerization reactions occur in the initial stage for natural rubber and in the middle stage for synthetic rubber, while the most significant release behavior occurs in the last stage. Accordingly, in the initial stage, TB shows a rapid evolution in macro properties due to the significant development of degradation reactions, specifically, the notable improvement in viscosity, compatibility, and low-temperature properties, as well as the substantial deterioration in high-temperature properties. In the middle stage, the degradation reaction develops further but slower, with TB exhibits a further but slower evolution in macro properties. In the last stage, the degradation reaction is almost completed, and TB shows a gradual stabilization of macro properties. The findings are expected to achieve precise control of CR degradation progression, which offers the possibility of efficient preparation of TB with specific properties, thus advancing the application of CR in pavement engineering.