The Ultraviolet Imager (UVI) is a challenging instrument developed in the frame of the SMILE mission, a collaboration between ESA and CAS. The UVI instrument is a CMOS-based ultraviolet camera developed to image Earth's northern auroral regions. It is centered on the 160-180 nm UV waveband, with a 10° × 10° field of view. At the core of the instrument, four thin film-coated mirrors guide light into its detector and ensure most of the signal filtering, crucial to achieve an out-of-band rejection ratio as low as possible to reject light from solar diffusion, dayglow and unwanted atomic lines. We developed an interferometric coating based on an MgF2/LaF3 multilayer stack deposited by ion-assisted electron-beam deposition. We gradually improved our evaporation setup to reach a high degree of homogeneity, precision and repeatability on the material thicknesses, over the entire mirrors surface. The reflectivity maximum is above 85% and the wavelength at which it occurs is adjustable within 1 nm, while the out-of-band reflectivity between 120 and 155 nm and between 200 nm and 1100 nm is kept below 6% on average never exceeding 8 %. The coating has been space qualified and shows stable performances in conditions representative of the instrument operation environment (thermal cycling under vacuum, radiations, UV exposure…).

The Ultraviolet Imager (UVI) instrument is a very challenging imager developed in the frame of the SMILE-ESA mission. The UV camera will consist of a single imaging system targeted at a portion of the Lyman-Birge-Hopfield (LBH) N2 wavelength band. The baseline design of the imager meets the requirements to record snapshots of auroral dynamics with sufficient spatial resolution to measure cusp processes (100 km) under fully sunlit conditions from the specified apogee of the spacecraft. To achieve this goal, the UVI instrument utilizes a combination of four on-axis mirrors with an intensified FUV CMOS based camera. The mirrors will be coated with spectral selective interferometric layers to provide most of the signal filtering. The objective of these filters is to select the scientific waveband between 160 and 180 nm. The combined four mirrors have to give an out-of-band rejection ratio as high as possible to reject light from solar diffusion, dayglow and unwanted atomic lines in a range of 10-8-10-9. Different multilayer coatings are considered and optimized according to the π-multilayer equation for different H/L ratio and for different angles of incidence. Our theoretical evaluation shows a least a modification of the reflectance spectrum as a function of the angle of incidence, so that the optical beams hitting the different mirrors can have different optical properties depending on the optical fields and the distribution of the rays on the pupil. In this paper the effect of fields and coating homogeneity on the spectral throughput of the UVI instrument will be assessed and described.

In the frame of the ICON (Ionospheric Connection Explorer) mission of NASA led by UC Berkeley, CSL and SSL Berkeley have designed in cooperation a new Far UV spectro-imager. The instrument is based on a Czerny-Turner spectrograph coupled with two back imagers. The whole field of view covers [± 12° vertical, ± 9° horizontal]. The instrument is surmounted by a rotating mirror to adjust the horizontal field of view pointing by ± 30°. To meet the scientific imaging and spectral requirements the instrument has been optimized. The optimization philosophy and related analysis are presented in the present paper. PSF, distortion map and spectral properties are described. A tolerance study and alignment cases were performed to prove the instrument can be built and aligned. Finally straylight and out of band properties are discussed.

This paper presents a new design of a planar solar concentrator for space applications focusing on two spatially separated PV cells, allowing independent control of output power of each cell. It has the advantages of both spectral splitting and solar concentration by the combination of a blaze transmission diffraction grating and a flat cylindrical Fresnel lens. An optical optimization has been realized and two variations of configuration have been developed to improve tracking tolerance: first, a design completed by secondary reflective concentrators and second, a symmetrical configuration composed of two lenses. First numerical results are presented, highlighting the possibility to design a concentrator at about 10×, with an electrical output power about 290W/m²_lens and less than 10% losses for tracking errors lower than ±0.9°.

A model is valid only if it represents the actual world. This paper presents several applications developed at CSL to improve or confirm multiphysic modeling, the difficulties of which being the coupling between several physical parameters, mechanics, thermals, optics⋯ The objectives of these applications are to improve, develop analytical modeling guidelines and confirm the models. Generally, the validation processes are carried out on simple test cases. The paper will demonstrate that simple test cases are not necessarily easy to measure, and that correlation with the model is not straightforward. Typical study cases presented are: - Heating of a spherical lens fixed in an aluminium barrel, with the presence of temperature gradients impacting the geometrical deformation of the lens and leading to refractive index gradients. - Samples with glued and bolted connections/junctions that can be encountered in stable structures on spacecraft (Silicon Carbide (SiC) and Titanium (TA6V)). These are measured by a holographic method. - The third system is a YAG laser bar heated by means of a dedicated oven. In the first test bench, the impact of thermo-elastic distortions on the optical performances has been measured using a Fizeau interferometer and compared to OOFELIE::Multiphysics' simulation results. The correlation between experimental and numerical data is discussed. For the second the thermo-mechanical correlations are performed, while for the last test bench preliminary testing results are presented.

The objective of this work is to demonstrate the correlation between a simple laboratory test bench case and the predictions of the OOFELIE Multiphysics software in order to deduce modeling guidelines and improvements. For that purpose two optical systems have been analyzed. The first one is a spherical lens fixed in an aluminium barrel, which is the simplest structure found in an opto-mechanical system. In this study, material characteristics are assumed to be well known: BK7 and aluminium have been retained. Temperature variations between 0 and +60°C from ambient have been applied to the samples. The second system is a YAG laser bar heated by means of a dedicated oven. For the two test benches thermo-elastic distortions have been measured using a Fizeau interferometer. This sensor measures wavefront error in the range of 20 nm to 1 μm without physical contact with the opto-mechanical system. For the YAG bar, birefringence and polarization measurements have also been performed using a polarimetric bench. The tests results have been compared to the predictions obtained by OOFELIE Multiphysics which is a simulation software dedicated to multiphysics coupled problems involving optics, mechanics, thermal physics, electricity, electromagnetism, acoustics and hydrodynamics. From this comparison modeling guidelines have been issued with the aim of improving the accuracy of computed thermo-elastic distortions and their impact on the optical performances.