Searched for: faculty:"Mechanical%2C%5C+Maritime%5C+and%5C+Materials%5C+Engineering"
(1 - 20 of 33,533)

Pages

document
Fibbe, S.T. (author)
Due to increasing cost pressure, disturbances from customs and an opportunity seen in reducing costs by increasing the procurement and construction in the Far East, Damen Shipyards Gorinchem is changing the requirements for its supply chain. Changes to the supply chain however not only inflicts a large number of stakeholders, but the cost...
master thesis 2021
document
de Goederen, R. (author), Pu, S. (author), Silos Viu, M. (author), Doan, D. (author), Overeem, S. (author), Serdijn, W.A. (author), Joosten, K. F.M. (author), Long, X. (author), Dudink, J. (author)
Study objectives: Unobtrusive monitoring of sleep and sleep disorders in children presents challenges. We investigated the possibility of using Ultra-Wide band (UWB) radar to measure sleep in children. Methods: Thirty-two children scheduled to undergo a clinical polysomnography participated; their ages ranged from 2 months to 14 years. During...
journal article 2021
document
den Boer, E. (author), Wulff, Jörg (author), Mäder, UIf (author), Engwall, Erik (author), Bäumer, Christian (author), Perko, Z. (author), Timmermann, Beate (author)
Purpose: Pencil beam scanning (PBS) for moving targets is known to be impacted by interplay effects. Four-dimensional computed tomography (4DCT)-based motion evaluation is crucial for understanding interplay and developing mitigation strategies. Availability of high-quality 4DCTs with variable breathing traces is limited. Purpose of this work...
journal article 2021
document
Moghaddam, E.M.C. (author), Foumeny, E.A. (author), Stankiewicz, A.I. (author), Padding, J.T. (author)
This paper investigates the validity of azimuthal averaging of 3D temperature fields in the analysis of lateral heat transfer in dense particle packings. This is conducted by synthetic generation of 3D packing surrogates of spheres, cylinders and Raschig rings with tube-to-pellet diameter ratio, 3 < N < 6, using an in-house Rigid Body...
journal article 2021
document
Wang, D. (author), Rueda, José L. (author), Rakhshani, E. (author), van der Meijden, M.A.M.M. (author)
Unlike synchronous generators, wind turbines cannot directly respond to large disturbances, which may cause transient instability, due to their power electronic-based interface and maximum power control strategy. To effectively monitor the influence of wind turbines, this paper proposes an approach that combines decision trees (DTs), and a...
journal article 2020
document
van Woerkom, P.Th.L.M. (author)
Joan Muysken, full professor in the Afdeling der Werktuigbouwkunde en Scheepsbouwkunde of the TH Delft 1932-1944 and rector magnificus of the TH Delft in the period 1943 – 1944.
report 2020
document
Deutz, D.B. (author), van der Zwaag, S. (author), Groen, P.C. (author)
As demand rises for flexible electronics, traditionally prepared sintered ceramic sensors must be transformed into fully new sensor materials that can bend and flex in use and integration. Negative temperature coefficient of resistance (NTC) ceramic thermistors are preferred temperature sensors for their high accuracy and excellent stability,...
journal article 2020
document
van Hengel, I.A.J. (author), Gelderman, F. S.A. (author), Athanasiadis, S. (author), Minneboo, M.B. (author), Weinans, H.H. (author), Fluit, A. C. (author), van der Eerden, B.C.J. (author), Fratila-Apachitei, E.L. (author), Apachitei, I. (author), Zadpoor, A.A. (author)
The holy grail of orthopedic implant design is to ward off both aseptic and septic loosening for long enough that the implant outlives the patient. Questing this holy grail is feasible only if orthopedic biomaterials possess a long list of functionalities that enable them to discharge the onerous task of permanently replacing the native bone...
journal article 2020
document
Hagen, N. (author)
A belt conveyor system is a commonly used mean of transportation for dry bulk material. The system components are subjected to wear because of the multiple rotating components. This will result in component failures on the long run. Maintenance or replacement actions are required for these components in order to prevent these system failures. In...
report 2019
document
Olberts, O.L. (author)
report 2019
document
Van Pampus, M.J. (author)
With growing demands on speed and amount of freight transport and simultaneous technological progress in data processing and the development of mobile applications, possibilities for the freight transport sector arise. In this paper we specifically look into the latest developments in the field of instant freight transport, i.e. services...
report 2019
document
Scali, M. (author), Veldhoven, P.A.H. (author), Henselmans, P.W.J. (author), Dodou, D. (author), Breedveld, P. (author)
Needles with diameter under 1 mm are used in various medical applications to limit the risk of complication and patient discomfort during the procedure. Next to a small diameter, needle steerability is an important property for reaching targets located deep inside the body accurately and precisely. In this paper, we present a 0.5-mm prototype...
journal article 2019
document
Plas, L.A. van der (author)
report 2018
document
Steenkamp, A.S.A. (author)
report 2018
document
Weerheim, R. (author)
report 2018
document
Borst, L. (author)
In order to fulfill the demands of today’s society considering efficient use of natural resources and energy, structural components designed by engineers are pushed to being more efficient in its use of material and energy. Structural optimization is a tool that can aid engineers with this goal. There are three types of structural optimization,...
report 2018
document
van der Linden, C.W.P. (author)
Industrial railway systems can be found within companies where the production and processing of goods require large quantities to be transported. These systems are often privately owned and are characterized by short to cover distances, many locations, inefficient layout due to historical expansion and bidirectional driving on the rail tracks....
master thesis 2018
document
Lavidas, G. (author)
journal article 2018
document
van den Hoed, M. (author)
master thesis 2018
document
Steendijk, J.J. (author)
report 2018
Searched for: faculty:"Mechanical%2C%5C+Maritime%5C+and%5C+Materials%5C+Engineering"
(1 - 20 of 33,533)

Pages