Nanoindentation is widely used to investigate the surface-mechanical properties of biocomposites. In this study, polypropylene random copolymer (PPRC) and biowaste rice husk (BRH) were used as the main raw materials, and glass-fiber-reinforced polypropylene and talc were also used with BRH to enhance the mechanical characterization of the biocomposites. The interfacial bonding between the polymer and the rice husk was increased by treating them with maleic anhydride and NaOH, respectively. The results obtained from the nanoindentation indicated that the plastic behavior of the biocomposites was prominent when untreated BRH was used and vice versa. The modulus and hardness of the biocomposite improved by 44.8% and 54.8% due to the neat PPRC, respectively. The tribological properties were studied based on the hardness-to-modulus ratio and it was found that BRH- and talc-based biocomposites were better than other samples in terms of low friction and wear rate. The creep measurements showed that untreated rice husk biocomposite exhibited high resistance to load deformation. @en

Organic–inorganic nanohybrids-based polymer nanocomposites are made up of two different components, and these hybrids attained great attention over last decades due to their diversified framework and fascinating features. These nanohybrids possess synergistic characteristics of both organic and inorganic substances. Different synthetic routes are used to synthesize these materials with enhanced morphology, tunable features, and fine nanostructures. This chapter focuses on various synthetic routes for fabrication of organic–inorganic-based nanopolymeric composites. Synthetic strategies and protocols of different routes have been described in details. We have also discussed the advantages and limitations of all synthetic methods in details.@en

Diverse applications of polymeric materials have prompted development of eco-friendly, efficient, and economical materials. These characteristics can be obtained by incorporating appropriate fillers in the polymeric matrix. The objective of this work is to investigate impact of aqueous glycerol (Gly) treated rice husk (RH) on surface mechanical properties of produced biocomposites. RH was treated with aqueous Gly (75 wt%) and compounded with low density polyethylene (LDPE) at different loadings (10, 20, and 30 wt%). The resulting mixture was thermally pressed in molds to fabricate biocomposites. Surface mechanical properties such as elastic modulus, hardness, creep rate, and plasticity of biocomposites reinforced with untreated and treated RH were investigated using nanoindenter. Experimental values depicted that hardness (H) and elastic modulus (E_s) of treated biocomposites were higher than untreated ones. Treated biocomposites showed the noticeable improvement in elastic modulus by 24 and 37% compared to untreated biocomposites at 20 wt% loading and neat LDPE, respectively. Reductions in the creep rate by 20 and 14% were observed for untreated and treated biocomposites, respectively, in comparison to the neat LDPE. H/E ratio was increased by 23 and 18% for treated and untreated biocomposites, respectively, as compared to virgin LDPE. Furthermore, mechanical and structural properties of untreated and treated RH are reported based on nanoindentation response and Fourier transform infrared spectroscopy (FTIR) techniques The study indicated that aqueous glycerol pretreatment can partially strip off non-cellulosic constituents from lignocellulose matrix to generate cellulose-rich pulp for engineered composite applications.@en

Nano-indentation, a depth sensing technique, is a useful and exciting tool to investigate the surface mechanical properties of a wide range of materials, particularly polymers. Knowledge of the influence of experimental conditions employed during nano-indentation on the resultant nano-mechanical response is very important for the successful design of engineering components with appropriate surface properties. In this work, nano-indentation experiments were carried out by selecting various values of frequency, amplitude, contact depth, strain rate, holding time, and peak load. The results showed a significant effect of amplitude, frequency, and strain rate on the hardness and modulus of the considered polymer, ultrahigh molecular weight polyethylene (UHMWPE). Load-displacement curves showed a shift towards the lower indentation depths along with an increase in peak load by increasing the indentation amplitude or strain rate. The results also revealed the strong dependence of hardness and modulus on the holding time. The experimental data of creep depth as a function of holding time was successfully fitted with a logarithmic creep model (R² ≥ 0.98). In order to remove the creeping effect and the nose problem, recommended holding times were proposed for the investigated polymer as a function of different applied loads.

@en

In this work, the effects of chemical pretreatment and different fiber loadings on mechanical properties of the composites at the sub-micron scale were studied through nanoindentation. The composites were prepared by incorporating choline chloride (ChCl) pretreated rice husk waste (RHW) in low-density polyethylene (LDPE) using melt processing, followed by a thermal press technique. Nanoindentation experiments with quasi continuous stiffness mode (QCSM) were performed on the surface of produced composites with varying content of pretreated RHW (i.e., 10, 15, and 20 wt.%). Elastic modulus, hardness, and creep properties of fabricated composites were measured as a function of contact depth. The results confirmed the appreciable changes in hardness, elastic modulus, and creep rate of the composites. Compliance curves indicated that the composite having 20 wt.% of pretreated RHW loading was harder compared to that of the pure LDPE and other composite samples. The values of elastic modulus and hardness of the composite containing 20 wt.% pretreated RHW were increased by 4.1% and 24% as compared to that of the pure LDPE, respectively. The creep rate of 42.65 nm/s and change in depth of 650.42 nm were also noted for the composite with RHW loading of 20 wt.%, which showed the substantial effect of holding time at an applied peak load of 100 mN. We believe that the developed composite could be a promising biodegradable packaging material due to its good tribo-mechanical performance.

@en

Bigels are interesting semisolid formulations with better properties for different applications such as cosmetics and pharmaceutical systems. Due to the mixing of two phases of different nature (polar and apolar), bigels possess some interesting features like ability to deliver hydrophilic and hydrophobic drugs, better spreadability and water washability, improved permeability of drugs, enhanced hydration of stratum corneum and ability to manipulate the drug release rate. The main objective of this review article is to provide a thorough insight into the important characteristics of bigels together with the discussion on modelling of bigel systems to relate their properties with individual constituents and different parameters. Moreover, some important applications of bigels are also discussed by considering some examples from the literature.@en

Ionic liquids (ILs) are liquid salts at ambient or lower temperatures and consist of ions and short-lived ion pairs. They are potential alternatives to toxic, hazardous, highly flammable, and volatile solvents for preparing solutions, dispersions, gels, composites, and polymeric melts. ILs have some very interesting and unique characteristics like good chemical and thermal stability and very low vapor pressures. They have good solvation interactions with a wide range of organic, inorganic, and polymeric compounds. They can enhance colloidal stability and the elasticity range of polymers. ILs are environmental friendly, easily recyclable, and structurally similar to the conventional solvents. For optimal performance, it is necessary to fully understand the rheological properties of ILs and their different systems for academic interests such as understanding the ability of ILs as processing AIDS particularly in film casting, fiber spinning and spraying, comprehension of thermodynamics and dynamics of polymer chains in ILs, analyzing the hydrodynamic volume of dispersed polymer, polymer-ILs interactions, characterizing the viscoelastic properties and nanophase-ILs interactions in nanocomposite systems, analyzing the plasticization efficiency, and the final properties of the composite system. The rheological analysis is also important for industrial purposes particularly for designing processing techniques and suitable operating conditions for IL based systems. The aim of this review is to give an overview of the rheological properties of pure ionic liquids and solutions, dispersions, gels, composites, and melts based on ionic liquids.@en

Polyether ether ketone (PEEK) is a semi-crystalline thermoplastic polymer having excellent mechanical and thermal properties. Exposure of this polymer to aliphatic and aromatic solvents can lead to degradation or swelling of the polymeric material. The present work described the plasticization and stability analysis of semi-crystalline PEEK under different aromatic and aliphatic solvent environment. A variety of solvents (acetone, benzene, benzyl alcohol, chloroform, methanol, and toluene), based on their Hildebrand’s Solubility Parameter, were chosen for investigation. The physico-chemical characteristics of virgin and treated polymeric samples were investigated using Gas Chromatography–Mass Spectrometry (GC–MS), Thermogravimetric Analysis (TGA), Differential Scanning Calorimetry (DSC), and Fourier Transform Infrared Spectroscopy (FTIR) techniques. The results indicated that the solvent exposure did not significantly affect the thermal behavior and chemical structure of the polymer. However, it seems that certain components of the polymer were leached into the solvent phase as revealed by the GC–MS analysis. The present study identified PEEK as a potentially suitable polymer for the applications where high resistance to aliphatic and aromatic solvents is needed.@en

Nano-indentation is an interesting tool for analyzing nano-scale mechanical properties. The analysis of nano-mechanical properties as a function of experimental conditions is very critical for designing engineering components. In this study, nano-indentation experiments were performed by considering different values of amplitude (1, 5, 10 nm), frequency (11.2, 22.5, 45 Hz), strain rate (0.02, 0.05, 0.1, 0.2, 1 s ⁻¹ ), peak load (10, 30, 100 mN) and hold time (1, 3, 5, 10, 20, 50, 100 sec) to analyze their effect on the mechanical properties of LDPE. The results showed that the effect of amplitude and frequency on the nano-mechanical properties of LDPE were negligible. Load-displacement curves displayed a shift towards higher indentation depths along with a decrease in peak load from 20.6 to 14.8 mN by having a decrease in strain rate from 1 to 0.02 s ⁻¹ . Elastic modulus and hardness values exhibited a decrease with an increase in hold time. Logarithmic creep model was used to fit the experimental data of creep as a function of holding time which showed good agreement (r ² ≥ 0.97) with the experimental values. Recommended holding times are also suggested to eliminate the creep and nose problem in order to achieve high accuracy in measurements.

@en