Heat flux enhancement resulting from utilization of variant graphene-based nanoparticles; graphenes, graphene nanoplatelets, graphene oxides (GOs), carbon nanotubes (CNTs which include single and multiple walled CNTs) in a water-base fluid is focussed in the present study. A steady, laminar, incompressible, mixed convective and reversed stagnation point flow together with the consideration of transverse magnetic field over varying angles of an inclined permeable cylinder is analyzed for the heterogeneous nanofluids. The governing partial differential equations based on Tiwari-Das model are reformulated into nonlinear ordinary differential equations by applying similarity expressions. A shooting procedure is opted to reformulate the equations into boundary value problems which are solved by employing a numerical finite difference code utilizing three-stage Lobatto IIIa formula in MATLAB. The effects of constructive parameters toward the model on non-dimensional velocity and temperature disseminations, reduced skin friction coefficient and reduced Nusselt number are graphically reported and discussed in details. It is observed that GOs-water has the lowest heat flux performance under increasing values of wall permeability parameter, curvature parameter and nanoparticle volume fraction as compared to other nanofluids. On contrary, our results demonstrate that graphenes-water has the highest heat flux performance as compared to SWCNTs-water across many emerging parameters considered in this study.

In the present research, the synthesis of highly stable multiwalled carbon nanotubes in aqueous media is developed using a one-pot, covalent and green functionalization technique to improve the heat transfer and hydrodynamic behavior of a horizontal stainless-steel tube subjected to a uniform heat flow at its outer surface. Instead of using corrosive inorganic acids, the free radical grafting of gallic acids is used in this procedure. In this work, GA-functionalized multiwalled carbon nanotubes water-based colloidal suspensions (nanofluids) were prepared at three different weight concentrations. Various characterization techniques comprising Fourier transform infrared spectroscopy, Raman spectroscopy, High resolution transmission Electron Microscopy, and zeta-potential measurements were performed and confirmed the success of MWCNT functionalization. The thermophysical properties were evaluated experimentally and validated using empirical correlations available in the literature. To prove the colloidal suspension stability, ultraviolet-visible spectroscopy was used, and the results showed that nanofluid was stable for almost 60 days. When the GAMWCNT concentration was increased, there was a significant improvement in the thermal conductivity. Moreover, the nanofluids' dynamic viscosity experienced a slight increment up to 7.30% when the GAMWCNTs were loaded relative to distilled water. Following the confirmation of the experimental setup's analytical correlations, tests for the colloidal GAMWCNT suspension flowing through a heated horizontal tube were carried out in a fully developed turbulent state. A significant enhancement in the convective heat transfer coefficient was obtained, with only minor growth in the relative pumping power by 33.05 and 1.19%, respectively. More importantly, the reported positive performance index indicator for all the Reynolds numbers of ranges shows the possibility of using the synthesized GAMWCNT aqueous suspensions as an alternative working fluid in heat transfer systems.

In industrial processes, the microtechnology concept refers to the operation of small devices that integrate the elements of operational and reaction units to save energy and space. The advancement of knowledge in the field of microfluidics has resulted in fabricating devices with different applications in micro and nanoscales. Micro-and nano-devices can provide energy-efficient systems due to their high thermal performance. Fluid flow in microchannels and microstructures has been widely considered by researchers in the last two decades. In this paper, a review study on fluid flow within microstructures is performed. The present study aims to present the results obtained in previous studies on this type of system. First, different types of flows in microchannels are examined. The present article will then review previous articles and present a general summary in each section. Then, the multi-phase flows inside the microchannels are discussed, and the flows inside the micropumps, microturbines, and micromixers are evaluated. According to the literature review, it is found that the use of microstructures enhances energy efficiency. The results of previous investigations revealed that the use of nanofluids as a working fluid in microstructures improves energy efficiency. Previous studies have demonstrated special attention to the design aspects of microchannels and micro-devices compared to other design strategies to improve their performance. Finally, general concluding remarks are presented, and the existing challenges in the use of these devices and suggestions for future investigations are presented.

Magnetic soft materials (MSMs) and magnetic shape memory polymers (MSMPs) have been some of the most intensely investigated newly developed material types in the last decade, thanks to the great and versatile potential of their innovative characteristic behaviors such as remote and nearly heatless shape transformation in the case of MSMs. With regard to a number of properties such as shape recovery ratio, manufacturability, cost or programming potential, MSMs and MSMPs may exceed conventional shape memory materials such as shape memory alloys or shape memory polymers. Nevertheless, MSMs and MSMPs have not yet fully touched their scientific-industrial potential, basically due to the lack of detailed knowledge on various aspects of their constitutive response. Therefore, MSMs and MSMPs have been developed slowly but their importance will undoubtedly increase in the near future. This review emphasizes the development of MSMs and MSMPs with a specific focus on the role of the magnetic particles which affect the shape memory recovery and programming behavior of these materials. In addition, the synthesis and application of these materials are addressed.

Heat flux enhancement due to utilization of graphene, graphene nanoplatelets, and graphene oxides in water/ethylene-glycol based nanofluids over an inclined permeable cylinder is focused in the present study. The governing PDE are reformulated into non-linear ODE by applying similarity expressions. A shooting procedure is opted to reformulate the equations into boundary value problems which are solved by employing a numerical finite difference code in MATLAB. The effects of constructive parameters toward the model on non-dimensional velocity and temperature dissemination, reduced skin friction coefficient and reduced Nusselt number are graphically reported and discussed in details. It is observed that by increasing the thermal stratification and inclination angle, the temperature profile and Nusselt number for the selected nanofluids will be decreased.