Robotic wire and arc additive manufacturing (WAAM) systems are required to provide predictable and efficient operations to fabricate solid metallic parts with high morphological fidelity and geometric accuracy. Since the metallic parts are fabricated based on a layer-by-layer principle, the interactions between the neighboring beads and layers strongly influence the geometric accuracy of the fabricated part. The layers-overlapping process has been studied and a traditional layers-overlapping model (T-LOM) has been published in the literature. This paper proposes a layers-overlapping strategy (LOS), based on which a revised layers-overlapping model (R-LOM) was proposed for the fabrication of multi-layer multi-bead (MLMB) components with homogeneous layers. A mathematical model for layers-overlapping is presented, which considers the material shortage areas at the edges of the layers. This is important since the material shortage areas result in a situation that the component width is smaller than the expected value. In addition, they will be accumulated when multiple layers are overlapped through normal unidirectional parallel (NUP) paths. The proposed LOS addresses two aspects: (i) the deposition amount of the first bead and the last bead in the lap layers should be increased and (ii) the deposition position of the first bead and the last bead in the lap layers should be moved towards the edges with a given offset distance. Validation experiments were designed and conducted to test the proposed concepts and models. The experimental results indicated that (i) the R-LOM enables the MLMB components to achieve the expected width and (ii) for components deposited with NUP paths, the R-LOM eliminates the effect of accumulation of material shortage areas on the first bead and increases the surface flatness.@en

An approach to repairing surface defects of metal parts is proposed, which includes a combined application of (i) groove machining, (ii) wire and arc additive manufacturing (WAAM), and (iii) finishing machining. The completed analysis revealed that (i) the inclination angle of the groove to be machined is strongly influenced by the manufacturing parameters of the WAAM process, and (ii) the WAAM process models designed for fabricating parts on a flat substrate are not appropriate for filling grooves. To overcome these issues, this research investigated the range of variation of the proper inclination angle of the groove. A mathematical model was developed to determine the manufacturing parameters of WAAM that result in a proper filling of the groove. The effectiveness of the proposed fundamentals was investigated in a case study. The experimental results showed that using the proposed approach and the chosen manufacturing parameters resulted in a complete filling of the machined groove. The fabrication error of the main part of the repaired region before the finishing machining was less than 0.3 mm, while the ‘buy-to-fly’ ratio of the deposited material was 92.1%. The proposed approach for morphological repair lends itself to a computer-aided automatic part repair process.@en

The deposition process of wire and arc additive manufacturing (WAAM) is usually planned based on a bead geometry model (BGM), which represents the relationship between bead geometries (e.g. width, height) and required deposition parameters. However, the actual deposition situation may deviate from the one in which the BGM is built, such as varied heat dissipation conditions, resulting in morphological changes of deposited beads and geometrical errors in the formed parts. In this paper, a novel control mechanism for enhancing the fabrication accuracy of WAAM based on fuzzy-logic inference is proposed. It considers the geometrical errors measured on already deposited layers and deposition context to adjust deposition parameters of beads in the subsequent layer, forming an interlayer closed-loop control (ICLC) mechanism. This paper not only presents the theoretical fundamentals of the ICLC mechanism but also reports the technical details about utilizing this mechanism to control the forming height of multi-layer multi-bead (MLMB) components. A fuzzy-logic inference machine was applied as the core component for calculating speed change of bead deposition based on height error and previously applied change. In terms of validation, the effectiveness of the proposed control mechanism and the implemented controller was investigated through both simulative studies and real-life experiments. The fabricated cuboid blocks showed good accuracy in height with a maximum error of 0.20 mm. The experimental results implied that the proposed ICLC approach facilitates deposition continuity of WAAM, and thus enables process automation for robotic manufacturing.

The deposition process of wire and arc additive manufacturing (WAAM) is usually planned based on a bead geometry model (BGM), which represents the relationship between bead geometries (e.g. width, height) and required deposition parameters. However, the actual deposition situation may deviate from the one in which the BGM is built, such as varied heat dissipation conditions, resulting in morphological changes of deposited beads and geometrical errors in the formed parts. In this paper, a novel control mechanism for enhancing the fabrication accuracy of WAAM based on fuzzy-logic inference is proposed. It considers the geometrical errors measured on already deposited layers and deposition context to adjust deposition parameters of beads in the subsequent layer, forming an interlayer closed-loop control (ICLC) mechanism. This paper not only presents the theoretical fundamentals of the ICLC mechanism but also reports the technical details about utilizing this mechanism to control the forming height of multi-layer multi-bead (MLMB) components. A fuzzy-logic inference machine was applied as the core component for calculating speed change of bead deposition based on height error and previously applied change. In terms of validation, the effectiveness of the proposed control mechanism and the implemented controller was investigated through both simulative studies and real-life experiments. The fabricated cuboid blocks showed good accuracy in height with a maximum error of 0.20 mm. The experimental results implied that the proposed ICLC approach facilitates deposition continuity of WAAM, and thus enables process automation for robotic manufacturing.@en

Wire and arc additive manufacturing (WAAM) is a competitive technology for fabricating metallic parts with complex structure and geometry. It enables the fabrication of multi-layer multi-bead (MLMB) parts. The basis of planning the deposition paths is the beads overlapping model (BOM). The existing overlapping models consider only the geometric area of adjacent beads, but ignore the spreading of the melted weld beads. The objective of the research was to develop an enhanced BOM (E.BOM) for WAAM, which takes the spreading of the weld beads into consideration. A deposited bead spreads to the already deposited neighboring bead and as a consequence, its center point deviates from the center point of the fed (to be melted) wire. Experiments were designed to explore the relationships between the geometries of the beads, and the offset distance between the center of a weld bead and the center of the fed wire. An artificial neural network was used to predict the offset distance of a certain weld bead based on the results of the experiments. In addition, a reasoning algorithm was implemented to calculate the optimal distance between the centers of adjacent deposition paths in order to achieve a planned center distance between adjacent beads. This enables the control of the actual center distance of the adjacent beads according to an expected value. The E.BOM has been tested by validation experiments. On the one hand, it improves the surface flatness of layers of MLMB parts produced by WAAM. On the other hand, it prevents formation of defects inside the parts.@en

Wire and arc additive manufacturing (WAAM) is a competitive technology for fabricating metallic parts with complex structure and geometry. It enables the fabrication of multi-layer multi-bead (MLMB) parts. The basis of planning the deposition paths is the beads overlapping model (BOM). The existing overlapping models consider only the geometric area of adjacent beads, but ignore the spreading of the melted weld beads. The objective of the research was to develop an enhanced BOM (E.BOM) for WAAM, which takes the spreading of the weld beads into consideration. A deposited bead spreads to the already deposited neighboring bead and as a consequence, its center point deviates from the center point of the fed (to be melted) wire. Experiments were designed to explore the relationships between the geometries of the beads, and the offset distance between the center of a weld bead and the center of the fed wire. An artificial neural network was used to predict the offset distance of a certain weld bead based on the results of the experiments. In addition, a reasoning algorithm was implemented to calculate the optimal distance between the centers of adjacent deposition paths in order to achieve a planned center distance between adjacent beads. This enables the control of the actual center distance of the adjacent beads according to an expected value. The E.BOM has been tested by validation experiments. On the one hand, it improves the surface flatness of layers of MLMB parts produced by WAAM. On the other hand, it prevents formation of defects inside the parts.@en