(1) Background: This study investigated the feasibility of conducting a two-week “real-world” trial of the Self Grasping Hand (SGH), a novel 3D printed passive adjustable prosthesis for hand absence; (2) Methods: Single-group pilot study of nine adults with trans-radial limb absence; five used body-powered split-hooks, and four had passive cosmetic hands as their usual prosthesis. Data from activity monitors were used to measure wear time and bilateral activity. At the end of the two-week trial, function and satisfaction were measured using the Orthotics and Prosthetics Users’ Survey Function Scale (OPUS) and the prosthesis satisfaction sub-scales of the Trinity Amputations and Prosthesis Experience Scale (TAPES). Semi-structured interviews captured consumer feedback and suggestions for improvement; (3) Results: Average SGH wear time over 2 weeks was 17.5 h (10% of total prosthesis wear time) for split-hook users and 83.5 h (63% of total prosthesis wear time) for cosmetic hand users. Mean satisfaction was 5.2/10, and mean function score was 47.9/100; (4) Two-week real-world consumer testing of the SGH is feasible using the methods described. Future SGH designs need to be more robust with easier grasp lock/unlock. @en

Background: Walking aids are designed for structural support during walking, however, surprisingly self-reported use of a walking aid (“Yes, I use one.”) has been identified as a risk factor for falling. Adjustment and design of walking aids may affect their usefulness in facilitating a stable walking pattern. We previously identified that increased body weight transfer onto a walking frame (‘device loading’) is associated with increased user stability. Research question: We asked: “Could adjustment of walking frame height to a lower height than clinically recommended serve as a mechanism to facilitate device loading and thereby increase stability? And: “Do ultra-narrow frames have an adverse effect on stability as compared to standard-width frames? Methods: Ten older adults that were users of front-wheeled walking frames walked with walking frames of 1) ‘standard width, standard height’, 2)‘standard width, low height’, 3)‘narrow width, standard height’. Smart Walker technology was used to record forces acting on the walking frame and inside the user's shoes, and cameras recorded relative position of the user's feet in relation to the frame's feet. Stability of the user-frame system and device loading (percent body weight transferred onto the frame) were calculated. A general linear mixed effects model was used for statistical analysis. Results: A lower height setting did not increase device loading and stability, therefore adjusting the height to a lower setting proved to be an unsuccessful mechanism to increase stability. However, device loading was positively correlated with stability for all frame conditions (p < 0.05). Finally, stability was reduced when walking with the ultra-narrow, as compared to standard-width, frame (p = 0.002). Significance: To increase stability in fall-prone users, active encouragement to transfer body weight onto the walking frame is needed. Considering the adverse effects of ultra-narrow frames on stability, such frames should be prescribed and used with caution.@en

Background: Walking aids are designed for structural support during walking, however, surprisingly self-reported use of a walking aid (“Yes, I use one.”) has been identified as a risk factor for falling. Adjustment and design of walking aids may affect their usefulness in facilitating a stable walking pattern. We previously identified that increased body weight transfer onto a walking frame (‘device loading’) is associated with increased user stability. Research question: We asked: “Could adjustment of walking frame height to a lower height than clinically recommended serve as a mechanism to facilitate device loading and thereby increase stability? And: “Do ultra-narrow frames have an adverse effect on stability as compared to standard-width frames? Methods: Ten older adults that were users of front-wheeled walking frames walked with walking frames of 1) ‘standard width, standard height’, 2)‘standard width, low height’, 3)‘narrow width, standard height’. Smart Walker technology was used to record forces acting on the walking frame and inside the user's shoes, and cameras recorded relative position of the user's feet in relation to the frame's feet. Stability of the user-frame system and device loading (percent body weight transferred onto the frame) were calculated. A general linear mixed effects model was used for statistical analysis. Results: A lower height setting did not increase device loading and stability, therefore adjusting the height to a lower setting proved to be an unsuccessful mechanism to increase stability. However, device loading was positively correlated with stability for all frame conditions (p < 0.05). Finally, stability was reduced when walking with the ultra-narrow, as compared to standard-width, frame (p = 0.002). Significance: To increase stability in fall-prone users, active encouragement to transfer body weight onto the walking frame is needed. Considering the adverse effects of ultra-narrow frames on stability, such frames should be prescribed and used with caution.@en

The Delft Self-Grasping Hand is an adjustable passive prosthesis operated using the concept of tenodesis (where opening and closing of the hand is mechanically linked to the flexion and extension of the wrist). As a purely mechanical device that does not require harnessing, the Self-Grasping Hand offers a promising alternative to current prostheses. However, the contralateral hand is almost always required to operate the mechanism to release a grasp and is sometimes also used to help form the grasp; hence limiting the time it is available for other purposes. In this study we quantified the amount of time the contralateral hand was occupied with operating the Self-Grasping Hand, classified as either direct or indirect interaction, and investigated how these periods changed with practice. We studied 10 anatomically intact participants learning to use the Self-Grasping Hand fitted to a prosthesis simulator. The learning process involved 10 repeats of a feasible subset of the tasks in the Southampton Hand Assessment Procedure (SHAP). Video footage was analysed, and the time that the contralateral hand was engaged in grasping or releasing was calculated. Functionality scores increased for all participants, plateauing at an Index of Functionality of 33.5 after 5 SHAP attempts. Contralateral hand involvement reduced significantly from 6.47 (first 3 attempts) to 4.68 seconds (last three attempts), but as a proportion of total task time remained relatively steady (increasing from 29% to 32%). For 9/10 participants most of this time was supporting the initiation of grasps rather than releases. The reliance on direct or indirect interactions between the contralateral hand and the prosthesis varied between participants but appeared to remain relatively unchanged with practice. Future studies should consider evaluating the impact of reliance on the contralateral limb in day-today life and development of suitable training methods. @en

Introduction The Delft Self-Grasping Hand (SGH) is an adjustable passive hand prosthesis that relies on wrist flexion to adjust the aperture of its grasp. The mechanism requires engagement of the contralateral hand meaning that hand is not available for other tasks. A commercialised version of this prosthesis, known as the mHand Adapt, includes a new release mechanism, which avoids the need to press a release button, and changes to the hand shape. This study is the first of its kind to compare two passive adjustable hand prostheses on the basis of quantitative scoring and contralateral hand involvement. Methods 10 anatomically intact participants were asked to perform the Southampton Hand Assessment Procedure (SHAP) with the mHand. Functionality and contralateral hand involvement were recorded and compared against SGH data originating from a previous trial involving a nearly identical testing regime. Results mHand exhibited higher functionality scores and less contralateral hand interaction time, especially during release-aiding interactions. Additionally, a wider range of tasks could be completed using the mHand than the SGH. Discussion Geometric changes make the mHand more capable of manipulating smaller objects. The altered locking mechanism means some tasks can be performed without any contralateral hand involvement and a higher number of tasks do not require contralateral involvement when releasing. Some participants struggled with achieving a good initial grip due to the inability to tighten the grasp once already formed. Conclusion The mHand offers the user higher functionality scores with less contralateral hand interaction time and the ability to perform a wider range of tasks. However, there are some design trade-offs which may make it slightly harder to learn to use. @en