Being able to quantify mechanical vibrations is of key importance for the safety of nuclear power plants, as they are able to induce damage. In this work, numerical simulations are used to compute water flow and vibration in a densely packed bundle of 7 rods, mimicking an experimental setup. This flow configuration is chosen to resemble the coolant flow through a nuclear reactor core. Because of the wall proximity, a considerable velocity difference between the narrow gaps and the subchannels exists, with an inflection point in the velocity profile. This yields an unstable situation, and large vortices are continuously created through a mechanism similar to the Kelvin–Helmholtz instability. The vortex streets in between the rods are associated with a fluctuating pressure field, causing vibrations of the rods. The experimental setup contains 7 steel cylinders, encased in a hexagonal duct. The central rod contains a section where the steel is replaced by a water-filled silicone tube, clamped at both extremes to the steel rod, and the vibrations of this section are examined. The numerical approach consists of coupled fluid–structure interaction (FSI) simulations, with the flow being modelled using computational fluid dynamics (CFD) and the structure using computational solid mechanics (CSM). The available experimental data consist of Laser Doppler Anemometry (LDA) measurements and high-speed camera footage of the wall movement of the silicone rod. Equivalent data is collected from the numerical simulations. The simulations are repeated for different flow rates. The frequency spectrum of the coherent structures, and the frequency and amplitude of the wall movement are compared for each operating point, as well as their trend as a function of the flow rate. The dominant frequencies found in the simulation results were similar to the experimental results, although slightly higher. They also showed a linear trend, just like the experiments. A larger mismatch was present for the structural response, the frequencies found using the FSI model being more than twice as high.@en

Fluid flows through rod bundles are observed in many nuclear applications, such as in the core of Gen IV liquid metal fast breeder nuclear reactors (LMFBR). One of the main features of this configuration is the appearance of flow fluctuations in the rod gaps due to the velocity difference in the sub-channels between the rods. On one side, these pulsations are beneficial as they enhance the heat exchange between the rods and the fluid. On the other side, the fluid pulsations might induce vibrations of the flexible fuel rods, a mechanism generally referred to as Flow Induced Vibrations (FIV). Over time, this might result in mechanical fatigue of the rods and rod fretting, which eventually can compromise their structural integrity. Within the SESAME framework, a joint work between Delft University of Technology (TU Delft), Ghent University (UGent), and NRG has been carried out with the aim of performing experimental measurements of FIV in a 7-rods bundle and validate numerical simulations against the obtained experimental data. The experiments performed by TU Delft consisted of a gravity-driven flow through a 7-rods, hexagonal bundle with a pitch-to-diameter ratio P/D=1.11. A section of 200 mm of the central rod was made out of silicone, of which 100 mm were flexible. Flow measurements have been carried out with Laser Doppler Anemometry (LDA) whereas a high-speed camera has measured the vibrations induced on the silicone rod. The numerical simulations made use of the Unsteady Reynolds-averaged Navier-Stokes equations (URANS) approach for the turbulence modelling, and of strongly coupled algorithms for the solution of the fluid-structure interaction (FSI) problems. The measured frequency of the flow pulsations, as well as the mean rod displacement and vibration frequency, have been used to carry out the benchmark.@en

Axial flow in tube bundles with small pitch-to-diameter ratio, a geometry encountered in nuclear reactor cores and heat exchangers, often displays periodic fluctuations. A significant velocity discrepancy between the inter-cylinder gap and subchannel center originates from the difference in through-flow area, feeding an instability. As it is associated with velocity-shear, it is similar to the Kelvin-Helmholtz type and the term 'gap instability' is adopted. A vortex street arises and structural vibration of the cylinders might develop due to the fluctuating pressure. Numerical simulations of this phenomenon were performed. The computational domain was constructed to match the most important geometrical features of an experimental setup. The bundle consists of 7 steel tubes in triangular array, placed in a hexagonal conduit. A flexible segment made of silicone is embedded in the central tube, with both extremes clamped to the steel parts of the cylinder. In the experiment, data of the fluctuating velocity was gathered using laser Doppler anemometry measurements. As first step, a completely rigid structure was considered. Unsteady Reynolds-averaged Navier-Stokes (URANS) simulations were used to test if this particular geometry also triggers the gap vortex street, which was the case. The phenomenon clearly appears as oscillations of the velocity components. Subsequently, fluid-structure interaction (FSI) simulations, taking into account the flexible part, allowed to assess the effect of the fluctuating flow field on the structure. A comparison between one-way and two-way coupled simulations was made.@en