Both 2D and 3D re-entrant designs are among the well-known prevalent auxetic structures exhibiting negative Poisson's ratio. The present study introduces novel analytical relationships for 2D re-entrant hexagonal honeycombs for both negative and positive ranges of the cell interior angle θ (θ<0 showing a negative Poisson's ratio). The derived analytical solutions are validated against finite element method (FEM) and experimental results. The results show that, compared to the analytical solutions available in the literature, the analytical relationships presented in this study provide the most accurate results for elastic modulus, Poisson's ratio, and yield stress. The analytical/computational tools are then implemented for designing Kinesio taping (KT) structures applicable to treatment of Achilles tendon injuries. One of the main features of the Achilles tendon is a natural auxetic behavior. Poisson's ratio distribution of an Achilles tendon is obtained using longitudinal and transverse strains and are then used to design and 3D print thermoplastic polyurethane (TPU) KT structures with non-uniform distribution of auxetic unit cells. The presented novel KT shows that it is capable of replicating the deformation and global and local Poisson's ratio distributions, similar to those of the Achilles tendon. Due to the absence of similar formulations and procedures in the literature, the results are expected to be instrumental for designing and 3D printing of flexible implants with unusual auxeticity.

With dramatic increase in 3D printing applications in industry, sandwich panels with 3D printed cores have gained a lot of attention recently. In harmony with global movement towards sustainability and low-carbon emission industries, sandwich panels with easy-to-repair and cost-effective cores would be very attractive structures. In this regard, implementing separated cells for constructing lattice structures instead of using back-to-back lattice structures makes repairing local damages in the core easier and more cost-effective. Ideally, a damaged cell can be replaced with an intact new cell without the need to change the whole core structure. In this study, mechanical responses of a single truncated cube unit cell, a well-known geometry for constructing regular lattices has been studied analytically, numerically, and experimentally. Analytical relationships were derived for stiffness, yield stress, and Poisson's ratio of a single unit cell. Samples were 3D printed and tested mechanically in large deformation regime. A good agreement between results from analytical derivations, numerical simulations, and experiments was observed. It was shown that an equilateral truncated cube structure has a yield stress at least twice of that for a simple cube structure. Three types of repairable sandwich panels with different uniform core densities as well as four graded cores were studied as well. The functionally graded sandwich panels presented the best performance while considering both energy absorption capacity and mass. The best functionally graded sandwich panels (Type 4) showed an increase in specific energy absorption (SEA) by almost 21% and a decrease in maximum displacement by 2.5% with respect to the second-ranking best option.

In the present study, the fatigue behavior and tensile strength of A6061-T4 aluminum al-loy, joined by friction stir spot welding (FSSW), are numerically investigated. The 3D finite element model (FEM) is used to analyze the FSSW joint by means of Abaqus software. The tensile strength is determined for FSSW joints with both a probe hole and a refilled probe hole. In order to calculate the fatigue life of FSSW joints, the hysteresis loop is first determined, and then the plastic strain amplitude is calculated. Finally, by using the Coffin-Manson equation, fatigue life is predicted. The results were verified against available experimental data from other literature, and a good agree-ment was observed between the FEM results and experimental data. The results showed that the joint’s tensile strength without a probe hole (refilled hole) is higher than the joint with a probe hole. Therefore, re-filling the probe hole is an effective method for structures jointed by FSSW subjected to a static load. The fatigue strength of the joint with a re-filled probe hole was nearly the same as the structure with a probe hole at low applied loads. Additionally, at a high applied load, the fatigue strength of joints with a refilled probe hole was slightly lower than the joint with a probe hole.

Bonded patches are widely used in several industry sectors for repairing damaged plates, cracks in metallic structures, and reinforcement of damaged structures. Composite patches have optimal properties such as high strength‐to‐weight ratio, easiness in being applied, and high flexibility. Due to recent rapid growth in the aerospace industry, analyses of adhesively bonded patches applicable to repairing cracked structures have become of great significance. In the present study, the fatigue behavior of the aluminum alloy, repaired by a double‐sided glass/epoxy composite patch, is studied numerically. More specifically, the effect of applying a double‐sided composite patch on the fatigue life improvement of a damaged aluminum 6061‐T6 is analyzed. 3D finite element numerical modeling is performed to analyze the fatigue performance of both repaired and unrepaired aluminum plates using the Abaqus package. To determine the fatigue life of the aluminum 6061‐T6 plate, first, the hysteresis loop is determined, and afterward, the plastic strain amplitude is calculated. Finally, by using the Coffin‐Manson equation, fatigue life is predicted and validated against the available experimental data from the literature. Results reveal that composite patches increase the fatigue life of cracked structures significantly, ranging from 55% to 100% for different applied stresses.