The paper proposes a novel methodology to locate and quantify entrapped air pockets created during pipe-filling events often found in intermittent water supply systems. Different filling conditions were tested in an experimental pipe with a high point. Measurements were taken and video recordings were carried out to assess air pocket volumes for different air release conditions at the downstream end of the pipe. The stochastic nature of air pocket creation resulted in varying air volumes. A new numerical model capable of simulating the air pocket creation, dragging and entrainment has been proposed. The new model, AirSWMM, was implemented as an extension of the Stormwater Management Model (SWMM) with stochasticity of air pocket formation reproduced by simulations with different air entrainment rates. The obtained numerical results show that the proposed model, even though based on a single-phase one-dimensional flow, can accurately locate and approximately quantify the entrapped air pocket volumes.@en

Pumps running as turbines are pointed out as a cost-effective solution for energy recovery in pressurised water supply systems. However, these hydraulic machines feature low efficiency under variable discharge operation due to the lack of an inlet flow control component. Variable speed operation is an approach for controlling the discharge at the pump as turbine inlet aiming at increasing the operational efficiency. This research work presents the experimental investigation for measuring the variable speed characteristic curves of pumps running as turbines, focusing on the turbine and on the extended operation modes. Three single-stage end-suction closed-impeller centrifugal pumps with different unit specific speed values are tested. Turbine mode test results show that the discharge-specific energy operating range is broadened with increasing efficiency if the machines are operated with variable speed. Extended operation results show that these hydraulic machines do not feature the instability region near the runaway conditions, the so-called the “s-curve”. Outcomes of this experimental investigation provide the required insights for establishing the design technical specifications of micro hydropower plants with variable speed pumps running as turbines, aiming at maximizing the energy recovered in pressurised water supply systems.@en

The current research focuses on the analysis of different dynamic effects of an air pocket located at mid-pipe length on transient pressures based on experimental data. Different flow rates and air pocket volumes are analysed. Several features are identified in the pressure-head signal associated with the air pocket: initial pressure drop, higher maximum overpressure peaks, increased pressure wave damping and delay. These features result from the superposition of pressure waves associated with the entrapped air contraction and expansion. Smaller air pockets generate minor reflections, whereas larger air-pockets tend to disperse and artificially attenuate maximum pressures. Video recording images of the air pocket during the transient event allow observation of two types of behaviour: one associated with lower transients, characterized by an air pocket volume variation with a clear air–water interface; and another one associated with more severe transients in which air mixes with water. Finally, there is a critical air pocket volume, independent of the initial flow rate, that leads to the highest overpressures.@en

The current research focuses on the analysis of different dynamic effects of an air pocket located at mid-pipe length on transient pressures based on experimental data. Different flow rates and air pocket volumes are analysed. Several features are identified in the pressure-head signal associated with the air pocket: initial pressure drop, higher maximum overpressure peaks, increased pressure wave damping and delay. These features result from the superposition of pressure waves associated with the entrapped air contraction and expansion. Smaller air pockets generate minor reflections, whereas larger air-pockets tend to disperse and artificially attenuate maximum pressures. Video recording images of the air pocket during the transient event allow observation of two types of behaviour: one associated with lower transients, characterized by an air pocket volume variation with a clear air–water interface; and another one associated with more severe transients in which air mixes with water. Finally, there is a critical air pocket volume, independent of the initial flow rate, that leads to the highest overpressures.@en

The current research focuses on the analysis of different dynamic effects of an air pocket located at mid-pipe length on transient pressures based on experimental data. Different flow rates and air pocket volumes are analysed. Several features are identified in the pressure-head signal associated with the air pocket: initial pressure drop, higher maximum overpressure peaks, increased pressure wave damping and delay. These features result from the superposition of pressure waves associated with the entrapped air contraction and expansion. Smaller air pockets generate minor reflections, whereas larger air-pockets tend to disperse and artificially attenuate maximum pressures. Video recording images of the air pocket during the transient event allow observation of two types of behaviour: one associated with lower transients, characterized by an air pocket volume variation with a clear air–water interface; and another one associated with more severe transients in which air mixes with water. Finally, there is a critical air pocket volume, independent of the initial flow rate, that leads to the highest overpressures.@en

The aim of this paper is the experimental characterization of a ball valve under steady and unsteady conditions, based on experimental tests carried out in a pressurized pipe system assembled at Instituto Superior Técnico. Data analysis showed that the response of the valve under steady-state conditions depends not only on the valve geometry and closure percentage, but also on the flow regime (i.e., Reynolds number); the comparison with values published in literature confirmed that typical valve head loss curves presented in manuals and textbooks refer to turbulent flows. The behavior under unsteady conditions was also analyzed based on transient pressure head measurements showing that the valve effective closure time varies between 4 and 10% of the total time of the maneuver. Two mathematical functions (hyperbolic and sigmoidal) are proposed to describe the discharge variation as a function of the total time of the maneuver and of the initial steady-state discharge; the most appropriate function depends on the simplifications imposed on the hydraulic transient simulator. A computational fluid dynamics (CFD) model was used to support the observed experimental behavior and to highlight the effect of the pipe length on the discharge variation.@en

Stormwater management model (SWMM) software has recently become a modeling tool for the simulation of intermittent water supply systems. However, SWMM is not capable of accurately simulating the air behavior in the pipe-filling phase, missing therefore a relevant factor during pipe pressurization. This work proposes the integration of a conventional accumulator model in the existing SWMM hydraulic model to overcome this gap. SWMM source code was modified to calculate the air piezometric head inside the pipe based on the system boundary conditions, and the air piezometric head was incorporated in the SWMM flow rate pressure component. Experimental data were collected during the rapid filling of a pipe system for three possible configurations that are likely to occur in intermittent water supply pipe systems: no air release, small air release, and large air release. Results show that the improved SWMM better describes the effect of the air behavior using the extended transport (EXTRAN) surcharge method when compared to the original SWMM. Results also show that the SLOT method with predefined slot width is not suitable for this purpose; thus, further research is needed to assess if an adjusted slot width could provide better results.@en