The properties of biofilm EPS are determined by the multiple interactions between its constituents and the surrounding environment. Because of the high complexity of biofilm EPS, its constituents' characterisation is still far from thorough, and identification of these interactions cannot be done yet. Therefore, we use gels of bacterial alginate-like exopolysaccharides (ALEs) as a model component for biofilm EPS in this work. These gels have been examined for their cohesive properties as a function of CaCl2 and KCl concentration. Hereto, ALE gel layers were formed on membranes by dead-end filtration of ALE solutions. Accumulation of the cations Ca2+ and K+ in the gels could be well predicted from a Donnan equilibrium model based on the fixed negative charges in the ALE. This suggests that there is no specific binding of Ca2+ to the ALE and that on the time scale of the experiments, the Ca2+ ions can distribute freely over the gel and the surrounding solution. The concentration of fixed negative charges in the ALE was estimated around 1 mmol/g VSS (volatile suspended solids, organic mass) from the Donnan equilibrium. Moreover, an accumulation of H+ was predicted. Gels with more CaCl2 in the supernatant were more compact and bore a higher osmotic pressure than those with less CaCl2, revealing the role of Ca2+ ions in the network crosslinking. It is hypothesised that this mechanism later transitions into a rearrangement of the ALE molecules, which eventually leads to a fibrous network structure with large voids.@en

Bacterial alginate-like exopolymers (ALE) gels have been used in this work as a model for the extracellular polymeric matrix of biofilms. Aim was to relate the mechanical properties and strength of this matrix that make biofilms as persistent to cleaning as they are, to the complex cohesive molecular interactions involved. Mechanical properties of the gels as a function of CaCO3 concentration were investigated using dynamic and static rheology. Gels with relatively low CaCO3 concentrations, between 100 μmol and 300 μmol per g ALE, were found to exhibit similar viscoelastic behaviour as real biofilms, with elastic moduli between 50 Pa and 100 Pa and dissipation factors between 0.2 and 0.3. Increasing CaCO3 concentrations resulted in an increase of the elastic modulus up to 250 Pa, accompanied by an increase in brittleness. At a CaCO3 concentration of 1250 μmol per g ALE this trend stopped, probably due to disturbance of the continuous ALE network by precipitation of salts. Therefore, overdosing of Ca salts can be an adequate approach for the removal of biofouling. All gels exhibited permanent strain hardening under medium strain, and their mechanical properties showed dependency on their strain history. Even after application of an oscillatory strain with 200% amplitude that caused the gel structure to collapse, the gels recovered 65 to 90% of their original shear modulus, for the major part within the first 20 s. Recovery was slightly less for gels with high CaCO3 concentration. In creep tests fitted with a Burgers model with multiple Kelvin elements at least three different interactions in the ALE gels could be distinguished with characteristic retardation times in the range of 10, 100 and 1000 s. Further identification of the mechanisms underlying the gel mechanics will allow the development of targeted strategies to undermine the mechanical strength of biofouling and aid the cleaning process.@en

Biofilms are the prevalent form of bacterial life on earth. Bacteria aggregate and embed themselves in a hydrogel matrix of extracellular polymeric substances (EPS), often spread over surfaces in thin films. The EPS matrix of biofilms is getting more and more attention from scientists for several reasons. On the one hand, it has been identified as the component of biofilms that is responsible for many of the adverse technological impacts of biofouling, for example for the increase of hydraulic resistance in membrane filtration systems. It has also been shown to provide structural integrity to biofilms and shield the embedded bacteria from chemicals, hampering removal in technological as well as medical environments. On the other hand, the same properties are interesting features for application as a biomaterial. Properties like water retention or the resilience against mechanical and chemical interference are defined by the molecular interactions between the different components of the EPS matrix. Therefore, a targeted biofouling cleaning strategy needs to start with understanding those molecular interactions. Owed to the high complexity and the to date still widely undisclosed molecular composition of biofilm EPS, research on these properties requires the use of models. In this work, several experimental and physical models were applied in order to unravel correlations between chemical composition, structure and mechanical properties of biofilm EPS in membrane filtration systems. @en