It is increasingly challenging to deal with the volume,variety, velocity, and veracity of misinformation (e.g., dissemination of fake news contents, spurious posts, and fabricated images/videos) from different online platforms. In this article, we present an overview of existing machine learning and information hiding-based misinformation detection techniques and discuss the current threats and limitations of these approaches. Based on the discussion, we identify a number of potential countermeasures. @en

Power modules applied in offshore applications are facing risks of corrosion failures on die-attach materials due to high humidity and H2S exposure. To investigate such corrosion behavior for sintered die-attach materials, we conducted a study with four groups of samples fabricated using copper and silver metal particles under different solvent systems. Such samples were firstly subjected to high-humidity-H2S conditions for 168 h to simulate the harsh offshore environment. After undergoing corrosion, the primary compounds formed were CuO/Cu2O and Ag2S through SEM, XRD, and XPS analysis. Notably, the incorporation of epoxy resin into sintered copper joints resulted in a remarkable reduction in corrosion and a substantial improvement in electrical conductivity after the reaction. In contrast, while the addition of epoxy did not evidently reduce corrosion in silver joints, it did lead to a significant increase in shear strength. Furthermore, to gain further insights into the effect of epoxy resin on corrosion behavior, electrochemical analysis, and molecular dynamics simulations were conducted. Finally, the mechanical reliability of the corroded copper and silver joints was evaluated through thermal shock tests. In summary, sintered copper joints exhibited better anti-corrosion behaviors than sintered silver under high humidity and H2S exposure, especially with the addition of epoxy resin. However, the corrosion products of sintered copper suffered from a sharp decrease in shear strength after thermal shock tests than sintered silver, which is probably due to the coefficient of thermal expansion mismatch.@en

Glacier surface albedo dominates glacier energy balance, thus strongly affecting the glacier mass balance. Glaciers in the Western Nyainqentanglha Mountains (WNM) experienced large mass losses in the past two decades, but long-term changes of glacier albedo and its drivers are less understood. In this study, we retrieved glacier albedo with MODIS reflectance data to characterize the spatiotemporal variability of albedo from 2001 to 2020. Air temperature, rainfall, snowfall and deposition of light-absorbing impurities (LAIs) were evaluated as potential drivers of the observed variability in glacier albedo. The results showed that: (1) the glacier albedo experienced large inter-annual fluctuations, with the mean albedo being 0.552 ± 0.002 and a clear decreasing trend of 0.0443 ± 2 × 10-4 dec-1 in the WNM. The fastest decline was observed in autumn and in the vicinity of the equilibrium line altitude, indicating an extended melt season and an expansion of the ablation region to higher elevation; (2) local meteorology and LAIs deposition are the main drivers of glacier albedo change, but their effects on seasonal albedos are different due to different glacier processes. Both air temperature and the balance between liquid and solid precipitation affect summer and autumn albedos due to glacier ablation. Air temperature is the main driver of spring and winter albedos due to sublimation and metamorphism of snow, while snowfall carried by westerlies has limited influence on these two seasonal albedos due to less snowfall. LAIs mainly affect spring albedo due to high concentration coupled with the southerly wind in spring. These findings highlight the significance of changes in glacier albedo and the key role of local meteorology and LAIs deposition in determining such changes, which play an important role in glaciological and cryosphere processes. @en

Glacier and snow are sensitive indicators of regional climate variability. In the early 21st century, glaciers in the West Kunlun and Pamir regions showed stable or even slightly positive mass budgets, and this is anomalous in a worldwide context of glacier recession. We studied the evolution of snow cover to understand whether it could explain the evolution of glacier area. In this study, we used the thresholding of the NDSI (Normalized Difference Snow Index) retrieved with MODIS data to extract annual glacier area and snow cover. We evaluated how the glacier trends related to snow cover area in five subregions in the Tarim Basin. The uncertainty in our retrievals was assessed by comparing MODIS results with the Landsat-5 TM in 2000 and Landsat-8 OLI in 2020 glacier delineation in five subregions. The glacier area in the Tarim Basin decreased by 1.32%/a during 2000–2020. The fastest reductions were in the East Tien Shan region, while the slowest relative reduction rate was observed in the West Tien Shan and Pamir, i.e., 0.69%/a and 1.08%/a, respectively, during 2000–2020. The relative glacier stability in Pamir may be related to the westerlies weather system, which dominates climate in this region. We studied the temporal variability of snow cover on different temporal scales. The analysis of the monthly snow cover showed that permanent snow can be reliably delineated in the months from July to September. During the summer months, the sequence of multiple snowfall and snowmelt events leads to intermittent snow cover, which was the key feature applied to discriminate snow and glacier.@en

Epithelial to mesenchymal transition (EMT) is crucial during embryonic development, tissue fibrosis, and cancer progression. Epithelial cells that display a cobblestone-like morphology can undergo a switch to mesenchymal-like phenotype, displaying an elongated spindle shape or a fibroblast-like morphology. EMT is characterized by timely and reversible alterations of molecular and cellular processes. The changes include loss of epithelial and gain of mesenchymal marker expression, loss of polarity, increased cell migratory and invasive properties. Epithelial cells can progress unevenly during this transition and attain hybrid E/M states or metastable EMT states, referred to as epithelial cell plasticity. To gain a deeper insight into the mechanism of EMT, understanding the dynamic aspects of this process is essential. One of the most prominent factors to induce EMT is the cytokine transforming growth factor-β (TGF-β). This chapter discusses molecular and cellular techniques to monitor TGF-β-induced signaling and EMT changes in normal and cancer cell lines. These methods include measuring the TGF-β-induced activation of its intracellular SMAD effectors proteins and changes in epithelial/mesenchymal marker expression and localization. Moreover, we describe assays of cell migration and dynamic reorganization of the actin cytoskeleton and stress filaments that are frequently part of the TGF-β-induced EMT cellular response.@en

With the increased deployment of power modules in demanding conditions, sintering materials, especially composite sintering materials, have raised growing interest due to their cost-effectiveness and suitability. Therefore, this study explores the viability of Cu–Ag composite sintering material, focusing on solvent influence through microstructure and mechanical behavior analysis. Micron-sized particle-based Cu–Ag composite pastes were designed and compared using eight solvents (four epoxy-free and four epoxy-added) based on fluidity and thermal stability. The sintered joints' performance, assessed through shear strength analysis, showed comparable values to pure silver sintering for both epoxy-free and epoxy-added samples. Optimized samples from each solvent system underwent reliability analysis, demonstrating that Cu–Ag joints with epoxy resin exhibited significantly higher shear strength after high-temperature storage and thermal cycling tests. Micromorphology and elemental composition analysis revealed differences in aging mechanisms, primarily attributed to variations in porosity due to oxide formation and pore filling by epoxy resin under different solvent systems. Further nanoindentation characterization of micromechanical properties, including hardness, modulus, and creep properties, during high-temperature aging, established constitutive models for insights into reliability evolution. In conclusion, the optimized epoxy-added Cu–Ag sintered joints proposed in this study demonstrated exceptional reliability and acceptable micromechanical properties, presenting a promising option for high-temperature power packaging.@en

With the increased deployment of power modules in demanding conditions, sintering materials, especially composite sintering materials, have raised growing interest due to their cost-effectiveness and suitability. Therefore, this study explores the viability of Cu–Ag composite sintering material, focusing on solvent influence through microstructure and mechanical behavior analysis. Micron-sized particle-based Cu–Ag composite pastes were designed and compared using eight solvents (four epoxy-free and four epoxy-added) based on fluidity and thermal stability. The sintered joints' performance, assessed through shear strength analysis, showed comparable values to pure silver sintering for both epoxy-free and epoxy-added samples. Optimized samples from each solvent system underwent reliability analysis, demonstrating that Cu–Ag joints with epoxy resin exhibited significantly higher shear strength after high-temperature storage and thermal cycling tests. Micromorphology and elemental composition analysis revealed differences in aging mechanisms, primarily attributed to variations in porosity due to oxide formation and pore filling by epoxy resin under different solvent systems. Further nanoindentation characterization of micromechanical properties, including hardness, modulus, and creep properties, during high-temperature aging, established constitutive models for insights into reliability evolution. In conclusion, the optimized epoxy-added Cu–Ag sintered joints proposed in this study demonstrated exceptional reliability and acceptable micromechanical properties, presenting a promising option for high-temperature power packaging.@en

Effective photolytic regeneration of the NAD(P)H cofactor in enzymatic reductions is an important and elusive goal in biocatalysis. It can, in principle, be achieved using a near-infrared light (NIR) driven artificial photosynthesis system employing H2O as the sacrificial reductant. To this end we utilized TiO2/reduced graphene quantum dots (r-GQDs), combined with a novel rhodium electron mediator, to continuously supply NADPH in situ for aldo-keto reductase (AKR) mediated asymmetric reductions under NIR irradiation. This upconversion system, in which the Ti-O-C bonds formed between r-GQDs and TiO2 enabled efficient interfacial charge transfer, was able to regenerate NADPH efficiently in 64 % yield in 105 min. Based on this, the pharmaceutical intermediate (R)-1-(3,5-bis(trifluoromethyl)phenyl)ethan-1-ol was obtained, in 84 % yield and 99.98 % ee, by reduction of the corresponding ketone. The photo-enzymatic system is recyclable with a polymeric electron mediator, which maintained 66 % of its original catalytic efficiency and excellent enantioselectivity (99.9 % ee) after 6 cycles.@en

Effective photolytic regeneration of the NAD(P)H cofactor in enzymatic reductions is an important and elusive goal in biocatalysis. It can, in principle, be achieved using a near-infrared light (NIR) driven artificial photosynthesis system employing H2O as the sacrificial reductant. To this end we utilized TiO2/reduced graphene quantum dots (r-GQDs), combined with a novel rhodium electron mediator, to continuously supply NADPH in situ for aldo-keto reductase (AKR) mediated asymmetric reductions under NIR irradiation. This upconversion system, in which the Ti-O-C bonds formed between r-GQDs and TiO2 enabled efficient interfacial charge transfer, was able to regenerate NADPH efficiently in 64 % yield in 105 min. Based on this, the pharmaceutical intermediate (R)-1-(3,5-bis(trifluoromethyl)phenyl)ethan-1-ol was obtained, in 84 % yield and 99.98 % ee, by reduction of the corresponding ketone. The photo-enzymatic system is recyclable with a polymeric electron mediator, which maintained 66 % of its original catalytic efficiency and excellent enantioselectivity (99.9 % ee) after 6 cycles.@en

Effective photolytic regeneration of the NAD(P)H cofactor in enzymatic reductions is an important and elusive goal in biocatalysis. It can, in principle, be achieved using a near-infrared light (NIR) driven artificial photosynthesis system employing H2O as the sacrificial reductant. To this end we utilized TiO2/reduced graphene quantum dots (r-GQDs), combined with a novel rhodium electron mediator, to continuously supply NADPH in situ for aldo-keto reductase (AKR) mediated asymmetric reductions under NIR irradiation. This upconversion system, in which the Ti-O-C bonds formed between r-GQDs and TiO2 enabled efficient interfacial charge transfer, was able to regenerate NADPH efficiently in 64 % yield in 105 min. Based on this, the pharmaceutical intermediate (R)-1-(3,5-bis(trifluoromethyl)phenyl)ethan-1-ol was obtained, in 84 % yield and 99.98 % ee, by reduction of the corresponding ketone. The photo-enzymatic system is recyclable with a polymeric electron mediator, which maintained 66 % of its original catalytic efficiency and excellent enantioselectivity (99.9 % ee) after 6 cycles.@en