The 16U4SBSP mission concept is based on using a swarm of CubeSats to perform a scaled demonstration of Space-Based Solar Power (SBSP) from Earth orbit. In this demonstration mission, seven identical spacecraft of 16U format are used to provide wireless energy in the kW-scale using Radio-Frequency (RF) Wireless Power Transfer (WPT), and the spacecraft in the swarm are designed to be suitable to both space-to-ground or space-to-space WPT applications. The main objective of the mission is to validate the general concept of providing SBSP using a swarm of satellites instead of a monolithic configuration, as well as some of the involved miniaturized technologies, in view of full-scale missions which could serve users in remote areas with low power requirements or support emergency operations in blackout zones affected by unpredicted hazards (e.g. natural disasters). More in general, the mission would represent a low-cost precursor towards MW-GW scale SBSP to supply clean and affordable energy from space to large areas on the Earth surface. A pre-Phase A study of the mission, funded by the European Space Agency (ESA) through the Sysnova campaign “Innovative Missions Concepts enabled by Swarms of CubeSats”, has led to encouraging results on the feasibility of the mission concept.

This paper presents in detail the final outcome of the pre-Phase A design effort for the 16U4SBSP spacecraft. The trade-off studies conducted to select all sub-systems and components are presented and their final outcomes detailed and justified, together with the technical budgets and the main areas of attention for the spacecraft design. Particularly critical for the success of the mission are the choices related to: the power transmission payload (DC-RF converter, transmitting antenna and heat dissipation system); the ADCS subsystem and in particular the sensors required to provide sufficient accuracy in the knowledge of the 3-axis attitude (both absolute and relative to the other spacecraft in the swarm); the relative navigation system, based on inter-satellite link between the spacecraft in the swarm and on a beacon link to the receiving station on ground, for efficient beaming coordination; the main propulsion system for continuous formation flying control through the whole mission lifetime; the electric power system, based on orientable solar arrays by means of a SADA mechanism and a set of batteries with sufficient capacity for beaming the required amount of power while in eclipse conditions. ... Read more

The 16U4SBSP mission aims to demonstrate Space-Based Solar Power (SBSP) using a CubeSat (CS) swarm from Earth orbit. This mission employs seven 16U CSs to deliver 1 kW-scale wireless energy via Radio-Frequency (RF) beaming, adaptable for space-to-ground and space-to-space applications. The goal is to validate SBSP provision using a satellite swarm and to explore miniaturized technologies for future large-scale missions. A pre-Phase 0 study funded by the European Space Agency (ESA) through the Sysnova campaign has shown encouraging feasibility results. This paper presents a study on the formation flying and orbital dynamics of a CS mission, using a model that includes Earth’s gravitational perturbations, solar radiation pressure (SRP), atmospheric drag, and lunar and solar gravity. The swarm configuration consists of seven CSs, with one at the center and six in a hexagonal arrangement. The Concept of Operations (CONOPS) is divided into three phases: deployment and acquisition, maintenance, and disposal. CSs are deployed at 30-second intervals, followed by a one-day Launch and Early Orbit Phase (LEOP) for subsystem checks. A 1000-meter formation is initially established, then reduced to 100 meters for the first half of the mission and 10 meters for the second half, maintained by a bang-bang limit-cycle controller. A disposal strategy compliant with ESA’s Space Debris Mitigation Requirements is outlined. The analysis characterizes propellant consumption at various altitudes, proposes optimal initial conditions and launch dates, and performs a trade-off analysis, resulting in a detailed mission characterization and baseline definition. The work presented in the paper proves the feasibility of the 16U4SBSP mission, which would supply clean energy from space through wireless power transfer. ... Read more

The 16U4SBSP mission concept is based on using a swarm of CubeSats to perform a scaled demonstration of SpaceBased Solar Power (SBSP) from Earth orbit. In this demonstration mission, seven identical spacecraft of 16U format are used to provide wireless energy in the kW-scale using Radio-Frequency (RF) Wireless Power Transfer (WPT), and the spacecraft in the swarm are designed to be suitable to both space-to-ground or space-to-space WPT applications. The main objective of the mission is to validate the general concept of providing SBSP using a swarm of satellites instead of a monolithic configuration, as well as some of the involved miniaturized technologies, in view of full-scale missions which could serve users in remote areas with low power requirements or support emergency operations in blackout zones affected by unpredicted hazards (e.g. natural disasters). More in general, the mission would represent a low-cost precursor towards MW-GW scale SBSP to supply clean and affordable energy from space to large areas on the Earth surface. A pre-Phase A study of the mission, funded by the European Space Agency (ESA) through the Sysnova campaign “Innovative Missions Concepts enabled by Swarms of CubeSats”, has led to encouraging results on the feasibility of the mission concept. This paper summarizes the main results of the 16U4SBSP pre-Phase A study, including the mission design and the possible way forward to the following steps in mission implementation (Phase A and later). A summary of the spacecraft system design and mission analysis is presented, as well as a short description of the mission CONOPS (concept of operations). Particular focus is given to the available options and objectives of the SBSP demonstration, and to the proposed solutions for RF power beaming, formation flying maintenance and end-of-life operations for compliance to the new ESA regulations on space debris mitigation. ... Read more

This paper introduces the use of a Chebychev moments' based feature for micro-Doppler based Classification, Recognition and Fingerprinting of Drones. This specific feature has been selected for its low computational cost and orthogonality property. The capability of the proposed feature extraction framework is assessed at three different levels of major classification steps, namely classification, recognition and fingerprinting, demonstrating the effectiveness of the proposed approach to discriminate drones from birds, fixed wings from multi-rotors and drones carrying different payloads on real measured radar data. ... Read more

In this paper a method capable of automatically classify radar signals of human hand-gestures exploiting the micro-Doppler signature is designed. In particular, the methodology focuses on the extraction of the Chebyshev moments from the cadence velocity diagram (CVD) of each recorded signal. The algorithm benefits from interesting properties of these moments such as the fact that they are defined on a discrete set and hence computed without approximations, as well as the symmetry property that allows to minimize the computational time. The experiments computed on the challenging real-recorded DopNet dataset show interesting results that confirm the effectiveness of the approach. ... Read more