In performance-based structural fire engineering, “travelling fires” is being gradually accepted as an important fire boundary condition. However, its application is still limited by uncertainties in the selection of different design travelling fire parameters, resulting from the lack of relevant experimental data and corresponding validated structural finite element models which can be used with advanced travelling fire methodologies, e.g. the Extended Travelling Fire Methodology (ETFM) framework. This paper aims to fill this gap through modelling a prototype steel-composite floor structure (representing a “slice” of a large open-plan office), to investigate its true structural response under a wide range of travelling fire scenarios, with an emphasis on considering the effect of concrete slab in a 3D finite element model, using LS-DYNA. To ensure the credibility of this numerical study, the model was first validated against the experimental data of the structural response from the Veselí Travelling Fire Test. In the parametric studies, 32 cases were examined to investigate the thermal and structural response, related to the selection of key design parameters for travelling fires (i.e. fire spread rates, fuel load densities and inverse opening factors (IOF)); fire protection (i.e. different fire protection schemes and required fire resistance rating (FRR)), and the effect of slab specification (i.e. thicknesses and steel reinforcements). It was found that solely satisfying the critical temperature and deflection criteria for the structural members might not guarantee a sufficient structural design for travelling fire scenarios, and it is suggested that the steel stress utilisation should also be examined. Compared with the IOF, it appears that the selection of fire spread rates and fuel load densities are likely to be more critical in identifying the worst travelling fire scenario for the structural response with fire protection. Moreover, the global structural response under travelling fire is also affected by the combination of fire protection (i.e. equivalent FRR in this paper) and fire spread rate. Under a “slow” travelling fire (e.g. 0.5 mm/s) with increasing FRR, the failure of structural elements during the cooling phase was prevented effectively; however, under a relatively “fast” travelling fire (e.g. 2.5 mm/s, 12.5 mm/s), increasing FRR may not always improve the fire performance of the structure. This work also indicates that steel reinforcement ratio has a greater influence on structural response than slab thickness under travelling fires. Furthermore, the 3D finite element model is very important for structural fire analysis, not only due to the more conservative internal force captured by the 3D model (i.e. reduced by over 80 % on the 2D model in our case) thereby reproducing the collapse triggered by the failure of the connection under fire in general, but also the 3D model was able to better represent the deflection and the “internal force reversal” caused by travelling fires.@en

The role of “travelling fires” is to ensure the robustness of structural design with large compartments under realistic fires, having a fire plume at the near-field, and a hot smoke layer preheating the ceiling at the far-field. Once the fire travels, the near-field has a leading edge representing the fire spread, and a trailing edge representing the burnout of the fuel. Though well understood by its definition, the mainstream of efforts on travelling fires for structural response is limited to 2D finite element modelling (FEM). This paper aims to identify the importance of slab inclusion with a 3D FEM structural model for steel-composite structures under travelling fires, with a special emphasis on the significance of ignoring the slab structural capacity contribution from a 2D simplified structural model. The role of fire protection scheme for 2D model against the 3D model on numerical predictions was also explored. It was found that the structural load path, and the potential structural failure mechanisms could be fundamentally different between the 3D model and the 2D model, i.e., with or without slabs. Although the 2D model tends to predict larger deflections (i.e. more conservative) than the 3D model, it could also significantly underestimate the large internal forces from the beams, which might overlook the connections failure under travelling fires. Further, due to the simplification of the 2D model omitting the significant stiffness contribution from the slab, the effect of the fire protection is likely to be amplified. It may be misleading for the performance-based structural fire design under different travelling fire scenarios. Hence, the 3D model is likely to be considered as necessary and feasible for structural fire analysis for travelling fires as a complement to the 2D model approach.@en

In the recent development of the performance-based structural fire design, the “travelling fire” methodology has been gradually accepted as a necessary fire boundary condition. However, its application is still limited by uncertainties in the selection of different design travelling fire parameters, which result from the lack of relevant experimental data and corresponding validated structural finite element models which can be used in advanced travelling fire methodologies, e.g. the extended travelling fire methodology (ETFM) framework. This paper aims to fill this gap through modelling a prototype steel-composite floor structure (regarded as a 'slice' of a large open-plan office), to investigate its true structural response under a wide range of travelling fire scenarios, with an emphasis on considering the effect of concrete slabs in a 3D finite element model, using LS-DYNA. To ensure the credibility of this numerical study, the model was validated against the experimental data from the Veselí Travelling Fire Test, and comparisons made with similar modelling efforts using Vulcan. In the parametric studies, eight cases were examined to investigate the structural response and the failure criteria, related to the selection of different key design parameters for the travelling fire within the ETFM framework, i.e. fire spread rate and inverse opening factor. It was found that solely satisfying the critical temperature (e.g. 550 o C for steel) and deflection criteria (e.g. beam span over 20) for the structural members might not guarantee a safe structural design for travelling fire scenarios, and it is suggested that the steel yielding stress status during the cooling phase in tension should also be examined. Compared to the inverse opening factor, it appears that the selection of fire spread rates is likely to be more critical in identifying the worst travelling fire scenario for the structural response with fire protection.@en