Radio link quality estimation inWireless SensorNetworks (WSNs) has a fundamental impact on the network performance and also affects the design of higher-layer protocols. Therefore, for about a decade, it has been attracting a vast array of research works. Reported works on link quality estimation are typically based on different assumptions, consider different scenarios, and provide radically different (and sometimes contradictory) results. This article provides a comprehensive survey on related literature, covering the characteristics of low-power links, the fundamental concepts of link quality estimation inWSNs, a taxonomy of existing link quality estimators, and their performance analysis. To the best of our knowledge, this is the first survey tackling in detail link quality estimation in WSNs. We believe our efforts will serve as a reference to orient researchers and system designers in this area.@en

Global Positioning System is a widely adopted localization technique. With the increasing demand for small satellites, the need for a low-power GPS for satellites is also increasing. To enable many state-of-the-art applications, the exact position of the satellites is necessary. However, building low-power GPS receivers which operate in low earth orbit pose significant challenges. This is mainly due to the high speed (∼7.8 km/s) of small satellites. While duty-cycling the receiver is a possible solution, the high relative Doppler shift between the GPS satellites and the small satellite contributes to the increase in Time To First Fix (TTFF), thus increasing the energy consumption. Further, if the GPS receiver is tumbling along with the small satellite on which it is mounted, longer TTFF may lead to no GPS fix due to disorientation of the receiver antenna. In this paper, we elucidate the design of a low-cost, low-power GPS receiver for small satellite applications. We also propose an energy optimization algorithm called F3to improve the TTFF which is the main contributor to the energy consumption during cold start. With simulations and in-orbit evaluation from a launched nanosatellite with our μGPS and high-end GPS simulators, we show that up to 96.16% of energy savings (consuming only ∼ 1/25th energy compared to the state of the art) can be achieved using our algorithm without compromising much (∼10 m) on the navigation accuracy. The TTFF achieved is at most 33 s.@en

UAVs are becoming versatile and valuable platforms for various applications. However, the main limitation is their flying time. We present BEAVIS, a novel aerial robotic platform striking an unparalleled trade-off between the maneuverability of drones and the long-lasting capacity of blimps. BEAVIS scores highly in applications where drones enjoy unconstrained mobility yet suffer from limited lifetime. A nonlinear flight controller exploiting novel, unexplored, aerodynamic phenomena to regulate the ambient pressure and enable all translational and yaw degrees of freedom is proposed without direct actuation in the vertical direction. BEAVIS has built-in rotor fault detection and tolerance. We explain the design and the necessary background in detail. We verify the dynamics of BEAVIS and demonstrate its distinct advantages, such as agility, over existing platforms including the degrees of freedom akin to a drone with 11.36 increased lifetime. We exemplify the potential of BEAVIS to become an invaluable platform for many applications.@en

For a long time, the Internet of Things initiative was driven by academics-developing embedded hardware, sensing algorithms, network protocols, software frameworks, applications, business scenarios, and interaction paradigms. Only recently industrial stakeholders realized the unparalleled potential of these technologies, instigating a paradigm shift that we refer to as the fourth industrial revolution. However, as this shift starts entering the mainstream and disrupting a multitude of business dynamics, it also uncovered myriads of challenges-some are technical, some are political, and some are ethical. In this special issue, together with our guest authors, we focus our attention on some of the daunting system development challenges in bringing bleeding-edge Internet of Things (IoTs) technologies to the real world. Each of the five articles featured in this issue tackles unique challenges associated with the deployment of real-world IoT systems.@en

We present radio-frequency (RF) information harvesting, a chan-nel sensing technique that takes advantage of the energy in the wireless medium to detect channel activity at essentially no en-ergy cost. RF information harvesting is essential for event-driven wireless sensing applications using battery-less devices that har-vest tiny amounts of energy from impromptu events, such as op-erating a switch, and then transmit the event notification to a one-hop gateway. As multiple such devices may concurrently de-tect events, coordinating access to the channel is key. RF infor-mation harvesting allows devices to break the symmetry between concurrently-transmitting devices based on the harvested energy from the ongoing transmissions. To demonstrate the benefits of RF information harvesting, we integrate it in a tailor-made ultra low-power hardware MAC protocol we call Radio Frequency-Distance Packet Queuing (RF-DiPaQ). We build a hardware/software proto-type of RF-DiPaQ and use an established Markov framework to study its performance at scale. Comparing RF-DiPaQ against sta-ple contention-based MAC protocols, we show that it outperforms pure Aloha and 1-CSMA by factors of 3.55 and 1.21 respectively in throughput, while it saturates at more than double the offered load compared to 1-CSMA. As traffic increases, the energy saving of RF-DiPaQ against CSMA protocols increases, consuming 36% less energy than np-CSMA at typical offered loads.@en