Modern wind turbine control algorithms typically utilize rotor effective wind speed measured from an anemometer on the turbine’s nacelle. Unfortunately, the measured wind speed from such a single measurement point does not give a good representation of the effective wind speed over the blades, as it does not take the varying wind condition within the entire rotor area into account. As such, Blade Effective Wind Speed (BEWS) estimation can be seen as a more accurate alternative. This paper introduces a novel Subspace Predictive Repetitive Estimator (SPRE) approach to estimate the BEWS using blade load measurements. In detail, the azimuth-dependent cone coefficient is firstly formulated to describe the mapping between the out-of-plane blade root bending moment and the wind speed over blades. Then, the SPRE scheme, which is inspired by Subspace Predictive Repetitive Control (SPRC), is proposed to estimate the BEWS. Case studies exhibit the proposed method’s effectiveness at predicting BEWS and identifying wind shear in varying wind speed conditions. Moreover, this novel technique enables complicated wind inflow conditions, where a rotor is impinged and overlapped by wake shed from an upstream turbine, to be estimated.@en

Economic model predictive control (EMPC) has received increasing attention in the wind energy community due to its ability to trade-off economic objectives with ease. However, for wind turbine applications, inherent nonlinearities, such as from aerodynamics, pose difficulties in attaining a convex optimal control problem (OCP), by which real-time deployment is not only possible but also a globally optimal solution is guaranteed. A variable transformation can be utilized to obtain a convex OCP, where nominal variables, such as rotational speed, pitch angle, and torque, are exchanged with an alternative set in terms of power and energy. The ensuing convex EMPC (CEMPC) possesses linear dynamics, convex constraints, and concave economic objectives and has been successfully employed to address power control and tower fatigue alleviation. This work focuses on extending the blade loads mitigation aspect of the CEMPC framework by exploiting its individual pitch control (IPC) capabilities, resulting in a novel CEMPC-IPC technique. This extension is made possible by reformulating static blade and rotor moments in terms of individual blade aerodynamic powers and rotational kinetic energy of the drivetrain. The effectiveness of the proposed method is showcased in a mid-fidelity wind turbine simulation environment in various wind cases, in which comparisons with a basic CEMPC without load mitigation capability and a baseline IPC are made.@en

With the ever increasing power rates of wind turbines, more advanced control techniques are needed to facilitate tall towers that are low in weight and cost-effective but in effect more flexible. Such soft-soft tower configurations generally have their fundamental side-side frequency in the below-rated operational domain. Because the turbine rotor practically has or develops a mass imbalance over time, a periodic and rotor-speed dependent side-side excitation is present during below-rated operation. Persistent operation at the coinciding tower and rotational frequency degrades the expected structural life span. To reduce this effect, earlier work has shown the effectiveness of active tower damping control strategies using collective pitch control. A more passive approach is frequency skipping by inclusion of speed exclusion zones, which avoids prolonged operation near the critical frequency. However, neither of the methods incorporates a convenient way of performing a trade-off between energy maximization and fatigue load minimization. Therefore, this paper introduces a quasi-linear parameter varying model predictive control (qLPV-MPC) scheme, exploiting the beneficial (convex) properties of a qLPV system description. The qLPV model is obtained by a demodulation transformation and is subsequently augmented with a simple wind turbine model. Results show the effectiveness of the algorithm in synthetic and realistic simulations using the NREL 5-MW reference wind turbine in high-fidelity simulation code. Prolonged rotor speed operation at the tower side-side natural frequency is prevented, whereas when the trade-off is in favor of energy production, the algorithm decides to rapidly pass over the natural frequency to attain higher rotor speeds and power productions.@en

The wind turbine side-side tower motion is known to be lightly damped. One viable active damping solution is realized by deploying individual pitch control (IPC) such that counteracting blade forces are created to alleviate the tower fatigue loading caused by this motion. Existing IPC methods for side-side tower damping in the literature, such as linear quadratic regulator and lead-lag controller, cannot accommodate direct optimization and tradeoff tunings of the wind turbine economic performance. In this work, a novel side-side tower damping IPC strategy under a convex economic model predictive control (CEMPC) framework is therefore developed to address these challenges. The main idea of the framework lies in the variable transformation in power and energy terms to obtain linear dynamics and convex constraints, over which the economic performance of the wind turbine is maximized with a globally optimal solution in a receding horizon manner. The effectiveness of the proposed method is showcased in a high-fidelity simulation environment under both steady and turbulent wind cases. Lower fatigue damage on the side-side tower bending moment is attained with an acceptable level of pitch activities, negligible impact on the blade loads, and minor improvement on the power production. @en