IP
Igor Petenko
info
Please Note
<p>This page displays the records of the person named above and is not linked to a unique person identifier. This record may need to be merged to a profile.</p>
2 records found
1
Journal article
(2020)
-
S.J.A. van der Linden, Bas J.H. van de Wiel, Igor Petenko, Chiel C. van Heerwaarden, Peter Baas, Harmen J.J. Jonker
High-resolution large-eddy simulations of the Antarctic very stable boundary layer reveal a mechanism for systematic and periodic intermittent bursting. A nonbursting state with a boundary layer height of just 3 m is alternated by a bursting state with a height of ≈5 m. The bursts result from unstable wave growth triggered by a shear-generated Kelvin–Helmholtz instability, as confirmed by linear stability analysis. The shear at the top of the boundary layer is built up by two processes. The upper, quasi-laminar layer accelerates due to the combined effect of the pressure force and rotation by the Coriolis force, while the lower layer decelerates by turbulent friction. During the burst, this shear is eroded and the initial cause of the instability is removed. Subsequently, the interfacial shear builds up again, causing the entire sequence to repeat itself with a time scale of ≈10 min. Despite the clear intermittent bursting, the overall change of the mean wind profile is remarkably small during the cycle. This enables such a fast erosion and recovery of the shear. This mechanism for cyclic bursting is remarkably similar to the mechanism hypothesized by Businger in 1973, with one key difference. Whereas Businger proposes that the flow acceleration in the upper layer results from downward turbulent transfer of high-momentum flow, the current results indicate no turbulent activity in the upper layer, hence requiring another source of momentum. Finally, it would be interesting to construct a climatology of shear-generated intermittency in relation to large-scale conditions to assess the generality of this Businger mechanism.
...
High-resolution large-eddy simulations of the Antarctic very stable boundary layer reveal a mechanism for systematic and periodic intermittent bursting. A nonbursting state with a boundary layer height of just 3 m is alternated by a bursting state with a height of ≈5 m. The bursts result from unstable wave growth triggered by a shear-generated Kelvin–Helmholtz instability, as confirmed by linear stability analysis. The shear at the top of the boundary layer is built up by two processes. The upper, quasi-laminar layer accelerates due to the combined effect of the pressure force and rotation by the Coriolis force, while the lower layer decelerates by turbulent friction. During the burst, this shear is eroded and the initial cause of the instability is removed. Subsequently, the interfacial shear builds up again, causing the entire sequence to repeat itself with a time scale of ≈10 min. Despite the clear intermittent bursting, the overall change of the mean wind profile is remarkably small during the cycle. This enables such a fast erosion and recovery of the shear. This mechanism for cyclic bursting is remarkably similar to the mechanism hypothesized by Businger in 1973, with one key difference. Whereas Businger proposes that the flow acceleration in the upper layer results from downward turbulent transfer of high-momentum flow, the current results indicate no turbulent activity in the upper layer, hence requiring another source of momentum. Finally, it would be interesting to construct a climatology of shear-generated intermittency in relation to large-scale conditions to assess the generality of this Businger mechanism.
Journal article
(2019)
-
Steven J.A. van der Linden, John M. Edwards, Chiel C. van Heerwaarden, Etienne Vignon, Christophe Genthon, Igor Petenko, Peter Baas, Harmen J.J. Jonker, Bas J.H. van de Wiel
Observations of two typical contrasting weakly stable and very stable boundary layers from the winter at Dome C station, Antarctica, are used as a benchmark for two centimetre-scale-resolution large-eddy simulations. By taking the Antarctic winter, the effects of the diurnal cycle are eliminated, enabling the study of the long-lived steady stable boundary layer. With its homogeneous, flat snow surface, and extreme stabilities, the location is a natural laboratory for studies on the long-lived stable boundary layer. The two simulations differ only in the imposed geostrophic wind speed, which is identified as the main deciding factor for the resulting regime. In general, a good correspondence is found between the observed and simulated profiles of mean wind speed and temperature. Discrepancies in the temperature profiles are likely due to the exclusion of radiative transfer in the current simulations. The extreme stabilities result in a considerable contrast between the stable boundary layer at the Dome C site and that found at typical mid-latitudes. The boundary-layer height is found to range from approximately 50m to just 5m in the most extreme case. Remarkably, heating of the boundary layer by subsidence may result in thermal equilibrium of the boundary layer in which the associated heating is balanced by the turbulent cooling towards the surface. Using centimetre-scale resolutions, accurate large-eddy simulations of the extreme stabilities encountered in Antarctica appear to be possible. However, future simulations should aim to include radiative transfer and sub-surface heat transport to increase the degree of realism of these types of simulations.
...
Observations of two typical contrasting weakly stable and very stable boundary layers from the winter at Dome C station, Antarctica, are used as a benchmark for two centimetre-scale-resolution large-eddy simulations. By taking the Antarctic winter, the effects of the diurnal cycle are eliminated, enabling the study of the long-lived steady stable boundary layer. With its homogeneous, flat snow surface, and extreme stabilities, the location is a natural laboratory for studies on the long-lived stable boundary layer. The two simulations differ only in the imposed geostrophic wind speed, which is identified as the main deciding factor for the resulting regime. In general, a good correspondence is found between the observed and simulated profiles of mean wind speed and temperature. Discrepancies in the temperature profiles are likely due to the exclusion of radiative transfer in the current simulations. The extreme stabilities result in a considerable contrast between the stable boundary layer at the Dome C site and that found at typical mid-latitudes. The boundary-layer height is found to range from approximately 50m to just 5m in the most extreme case. Remarkably, heating of the boundary layer by subsidence may result in thermal equilibrium of the boundary layer in which the associated heating is balanced by the turbulent cooling towards the surface. Using centimetre-scale resolutions, accurate large-eddy simulations of the extreme stabilities encountered in Antarctica appear to be possible. However, future simulations should aim to include radiative transfer and sub-surface heat transport to increase the degree of realism of these types of simulations.