As the shift towards renewable energy continues, larger monopiles are being installed to accommodate for the increasing size of wind turbines. To allow for safe and economical installation of these monopiles, reliable and efficient models to predict hydrodynamic forces during installation are needed. This thesis investigates the hydrodynamic forces and inner water surface behavior acting on a very large (15 meter) diameter monopile during a vertical lowering operation.

A Landing Platform Dock (LPD) facilitates amphibious operations by allowing landing vessels such as the Landing Craft Vehicle Personnel (LCVP) and Landing Craft Utility (LCU) to embark and disembark from its internal flooded well-dock. The smooth transition of these landing vessels is critical, but can be hindered by wave motions (i.e. sloshing) within the well-dock, making safe embarking and disembarking more difficult.

Existing literature mainly describes wave motions within a well-dock, but does not address how to minimise these motions. This thesis aims to develop a preliminary design to reduce wave energy entering the dock by implementing an optimised wave attenuation solution.

ComFLOW is used to observe that wave motions inside the well-dock are highly non-linear and correspond to the LPD’s oscillation period. The wave motions within the dock are caused by a drop in water level near the well-dock entrance. This causes waves to roll into the dock. In shallow water conditions like in the well-dock, the propagating waves hereby show amplitude dispersion and wave breaking.

Using a system engineering approach, a bottom-hinged pitching flap was found to be ideal for wave attenuation in shallow water conditions. The flap’s attenuation performance was examined using ComFLOW by adjusting design parameters such as: mass, center of gravity, length and mechanical damping.

It was found that high-period waves with high wave heights fully couple dynamically with the flap, resulting in several outcomes. First, the flap follows the wave frequency, resulting in sub-optimal energy dissipation with use of radiation damping. Second, tuning the flap’s natural period to match the incoming wave period, increases pitching angles but reduces angular velocity, leading to decreased wave attenuation. Third, lowering the centre of gravity increases the restoring moment and angular velocity. This results in enhanced energy dissipation of higher-order wave components. Fourth, increasing the flap’s length improves wave attenuation due to enhanced reflection and radiation damping. Fifth, adding mechanical damping decreases attenuation performance, likely because the reduction in angular velocity worsens the energy dissipation effect for higher-order wave components. This research revealed that the best performing solution, with low a centre of gravity, attenuates 28.7% of wave energy entering the well-dock. Furthermore, optimising the flaps natural period to the incoming wave period was less effective, attenuating only 19.7% of the wave energy.

Green water events on ships in extreme waves pose a considerable risk to personal, operational, and structural safety. Considering these issues, novel experiments were done to investigate the interaction between focused breaking waves and a ship at forward speed. The investigated interactions are global motion, global loads, and forces on a deck structure.

For the experiments focused, breaking waves were created, which served as loads of the green water events. First, wave focusing with prescribed characteristics was investigated in numerical settings. It was shown that focusing the waves with iterative methods does not lead to a converging solution. Three breaking waves were created in a wave basin. The characteristics of the waves were retrieved from 2D numerical simulations. The parameters of the spectrum of each wave were calculated from the simulation results.

The experiments were conducted systematically, where the position of the longitudinal center of gravity (LCG) of the ship was varied with respect to the focus point of the breaking wave at the focusing time. Using the same wave input resulted in green water events and loads on deck structure with different characteristics caused by different breaking stages of the focused wave. The effects of different ship velocities and different focused breaking waves were also explored throughout the experiments. It was shown that using the same focused wave, i.e., the same energy input, the breaking stage of the wave during the impact has a large influence on both the magnitude and time development of the loads on the deck structure. Force and pressure peaks were the largest and had an initial spike-like development when the wave during impact was in an unbroken stage. Impacts with the wave in its broken stage resulted in significantly lower loads and longer-duration load development. Such changes in the loads show that the ship's position with respect to the breaking wave is essential to consider even for the same input energy, posing additional challenges for establishing the maximum load in a sea state.