Application of 3D Printing in Pharmaceutical Sciences, and Evaluation of Administration Routes for Drug-Loaded Composites

3D printing is a novel approach in the pharmaceutical field, but its usage has not been fully established. This method can promote drug therapy and overcome some traditional treatment challenges in different ways that are discussed in this paper. “One-size-fits-all”, Large-scale production, and less patient and physician acceptability are...

Fuzzy logic based active vibration control using novel photostrictive composites

Although conventional actuators like piezoelectric and electrostrictive are efficient, but they required hard wiring, which contaminates the control signal and adds to the weight of the structure. The current study presents a wireless control strategy using photostrictive actuators. Owing to the fortunate combination of photovoltaic effect...

Extrusion-based additive manufacturing of Mg-Zn/bioceramic composite scaffolds

The treatment of femoral nonunion with large segmental bone defect is still challenging. Although magnesium alloys have been considered potential materials for such a treatment, their application is limited by their fast degradation. Adding bioceramic particles into magnesium to form Mg-matrix composites is a promising strategy to adjust...

Additive manufacturing of bioactive and biodegradable porous iron-akermanite composites for bone regeneration

Advanced additive manufacturing techniques have been recently used to tackle the two fundamental challenges of biodegradable Fe-based bone-substituting materials, namely low rate of biodegradation and insufficient bioactivity. While additively manufactured porous iron has been somewhat successful in addressing the first challenge, the limited...

Influence of Sintering Temperature on the Structural, Morphological, and Electrochemical Properties of NiO-YSZ Anode Synthesized by the Autocombustion Route

In this study, nickel oxide–Y2O3-doped ZrO2 (NiO-YSZ) composite powder as an anode material was synthesized using a cost-effective combustion method for high-temperature solid oxide fuel cell (SOFC). Further, the effects of sintering temperatures (1200, 1300, and 1400 °C) were studied for its properties in relation to the SOFC performance. The...

Microstructural basis for improved corrosion resistance and mechanical properties of fabricated ultra-fine grained Mg-Akermanite composites

In the present research, a composite with a magnesium alloy (WE43) as the matrix and Akermanite as the bioactive and reinforcing agent was fabricated by friction stir processing (FSP), resulting in a microstructure with uniformly distributed fine grains, second-phase particles and micro-sized Akermanite particles. The effect of an addition of...

A simultaneous dual-parameter optical fibre single sensor embedded in a glass fibre/epoxy composite

A simultaneous two-parameter single sensor based on weakly tilted Fibre Bragg Grating (TFBG), embedded in a 1 mm glass fibre/epoxy composite plate, is demonstrated to measure independently the temperature and strain variations induced in the material by the exposure to heating lamps. The spectrum of weakly TFBGs is composed of several peaks...

Bondline thickness effects on damage tolerance of adhesive joints subjected to localized impact damages: Application to leading edge of wind turbine blades

The leading edges of wind turbine blades are adhesively bonded composite sections that are susceptible to impact loads during offshore installation. The impact loads can cause localized damages at the leading edges that necessitate damage tolerance assessment. However, owing to the complex material combinations together with varying bondline...

Static and dynamic aeroelastic tailoring with composite blending and manoeuvre load alleviation

In aircraft design, proper tailoring of composite anisotropic characteristics allows to achieve weight saving while maintaining good aeroelastic performance. To further improve the design, dynamic loads and manufacturing constraints should be integrated in the design process. The objective of this paper is to evaluate how the introduction of...

Static aeroelastic stiffness optimization of a forward swept composite wing with CFD-corrected aero loads

This paper presents an aero load correction strategy applicable to the static aeroelastic optimization of composite wings. The optimization framework consists of a successive convex subproblem iteration procedure, in which a gradient-based optimizer consecutively solves a local approximation problem. Responses are approximated as a linear and...

ES-PIM applied to buckling of variable angle tow laminates

The increasing need for automatic mesh generation has led to the development of efficient triangulation algorithms that are able to discretize any 2D or 3D domain. Modern finite element formulations based on strain smoothing techniques (SFEM) provide enhanced convergence properties, preventing yet the stiffening behavior of triangular meshes....

Biodegradation and mechanical behavior of an advanced bioceramic-containing Mg matrix composite synthesized through in-situ solid-state oxidation

Recent studies have shown great potential of Mg matrix composites for biodegradable orthopedic devices. However, the poor structural integrity of these composites, which results in excessive localized corrosion and premature mechanical failure, has hindered their widespread applications. In this research, an in-situ Powder Metallurgy (PM)...

Adaptive and composite thin glass concepts for architectural applications

Thin glass – such as commonly applied for displays and touchscreen on electronic devices like smartphone and tablets – offers interesting characteristics for architectural applications. Due to its high strength and small thickness the glass can easily be bent in architecturally appealing curvatures, while the small thickness of the glass offers...

Minimum compliance topology optimization of shell–infill composites for additive manufacturing

Additively manufactured parts are often composed of two sub-structures, a solid shell forming their exterior and a porous infill occupying the interior. To account for this feature this paper presents a novel method for generating simultaneously optimized shell and infill in the context of minimum compliance topology optimization. Our method...