Numerical analysis of the effect of the scan strategy on the residual stress in the multi-laser selective laser melting

The inevitably formed residual stress in the Selective Laser Melting (SLM) process leads to distortion, crack and even delamination of the workpiece. Single laser is commonly applied during SLM processing. However, its productivity is much lower than multiple lasers. In addition, the research of residual stress with multi-laser condition...

Numerical investigation on the surface crack growth in FRP-reinforced steel plates subjected to tension

In this paper, we analyse the surface crack growth in the Fibre-Reinforced Polymer (FRP) reinforced steel plates subjected to tension by means of the finite element (FE) method. Following the experimental study, a three-dimensional FE model is developed to evaluate the Stress Intensity Factor (SIF) of the surface crack, and the crack growth...

Experimental investigation on FRP-reinforced surface cracked steel plates subjected to cyclic tension

Surface cracked steel plates reinforced with single-side Fiber-Reinforced Polymer (FRP) subjected to cyclic tension are experimental studied. The main purpose is to analyze the effect of FRP reinforcement on the crack growth. The failure modes and their effects are analyzed as well. Given the single-side reinforcement, reinforcing the cracked...

External surface cracked offshore steel pipes reinforced with composite repair system subjected to cyclic bending: An experimental investigation

In this paper, we experimentally studied the external surface crack growth in steel pipes reinforced with Composite System Repaired (CRS). CRS reinforced surface cracked API 5L X65 pipes were tested, containing three initial notch sizes and four reinforcement schemes. During the tests, the crack growth results, as well as the strain on the...

An investigation on the circumferential surface crack growth in steel pipes subjected to fatigue bending

In the present paper, we propose an analytical method to calculate the Stress Intensity Factor (SIF) of circumferential surface cracks in steel pipes subjected to bending. In light of pipe geometry and bending load case, the analytical formula is raised by introducing new bending correction factors and new geometry correction factors on the...

Impact of high temperature H₂ pre-treatment on Pt-AlGaN/GaN HEMT sensor for H₂S detection

In this paper, a method to extend the detection range of hydrogen sulfide (H₂S) gas sensor is demonstrated. The sensor is based on AlGaN/GaN high electron mobility transistors (HEMTs) with Pt gate. It is observed that the as-fabricated devices exhibited sensing signal saturation at 30 ppm H₂S exposure in dry air. A pre...

Contractor cooperation mechanism and evolution of the green supply chain in mega projects

The large scale of construction in mega projects leads to significant environmental and socioeconomic impacts; thus, the projects should also exhibit greater social responsibility. Adopting green supply chain management in the construction process is an important way to realize the goal of sustainable development of mega projects. Because the...

Generation and detection of non-Gaussian phonon-added coherent states in optomechanical systems

Fe2O3 Nanoparticle Seed Catalysts Enhance Cyclability on Deep (Dis)charge in Aprotic Li-O2 Batteries

Understanding the Electrochemical Formation and Decomposition of Li2O2 and LiOH with Operando X-ray Diffraction

The lithium air, or Li–O2, battery system is a promising electrochemical energy storage system because of its very high theoretical specific energy, as required by automotive applications. Fundamental research has resulted in much progress in mitigating detrimental (electro)chemical processes; however, the detailed structural evolution of the...

Towards the integration of indoorGML and indoorlocationGML for indoor applications

This paper introduces and compares two types of GML-based data standards for indoor location-based services, i.e., iIndoorGML and iIndoorLocationGML. By elaborating the advantages of the both standards and their data models, we conclude that the two data standards are complementary to each other. A jointed data model is presented to show the...

Free multi-floor indoor space extraction from complex 3D building models

Intelligent navigation and facility management in complex indoor environments are issues at the forefront of geospatial information science. Indoor spaces with fine geometric and semantic descriptions provide a solid foundation for various indoor applications, but it is difficult to comprehensively extract free multi-floor indoor spaces from...

Indoor Multi-Dimensional Location GML and Its Application for Ubiquitous Indoor Location Services

The Open Geospatial Consortium (OGC) Geography Markup Language (GML) standard provides basic types and a framework for defining geo-informational data models such as CityGML and IndoorGML, which provide standard information models for 3D city modelling and lightweight indoor network navigation. Location information, which is the semantic engine...