- document
-
Oldersma, A. (author), Wanhill, R.J.H. (author)Discussions between D-BAA and the NLR have shown that significant variability in fatigue crack growth properties is possible for the industry standard damage tolerant aluminium alloy, 2024-T3 sheet. This is important for two reasons: (1) design assumptions and (2) comparisons of different candidate materials, such as 6013-T6, with 2024-T3....report 1996
- document
-
ten Have, A.A. (author)The RNLN Fleet Air Arm (Marine Luchtvaartdienst) has recently implemented a series of usage monitoring procedures for optimisation of Orion and Lynx operation. Goal is an enhancement of efficiency, economy and safety of the usage of both aircraft systems. Compared to the benefits, the efforts for achieving useful usage monitoring are relatively...report 1991
- document
-
Kolkman, H.J. (author)Differences in the fatigue crack propagation rates of 2024-T351 and 2324-T39 are explicable from differences in microstructures. The slope changes (transitions) in the crack propagation curves are probably associated with the plastic zone sizes being equal to certain microstructural dimensions. As a consequence of different chemical compostion...report 1985
- document
-
Wanhill, R.J.H. (author)Flight simulation fatigue crack propagation tests on 202U-T3 and 7475-T761 aluminum alloy sheet were carried out using a gust spectrum representative of the load history of an under wing skin in a transport aircraft. The investigation included tests at several design stress levels and in environments of laboratory air and air plus water spray....report 1980
- document
-
de Jonge, J.B. (author)Due to the development of servo hydraulic fatigue testing machines, fatigue tests under realistic loading conditions have become possible. In these tests, standardized load sequences can be applied. The paper describes the main properties of such sequences, including TWIST and FALSTAFF. Various examples of application of these sequences are...report 1980
- document
-
Lowak, H. (author), de Jonge, J.B. (author), Franz, J. (author), Schutz, D. (author)The Transport Wing Standard programme (TWIST) published in March 1973 is considered to be representative for the load history of the wing root of transport aircraft. A description of the shortened version of this load programme called MINITWIST is given in the present report. In all cases where testing time is a prohibitive factor to use TWIST,...report 1979
- document
-
Schijve, J. (author), Jacons, F.A. (author), Meulman, A.E. (author)Flight simulation tests on 2024-T3 and 7075-T6 lug specimens indicated significant fatigue life improvements obtained by expanding the holes in accordance with the split-sleeve cold work method. Geometrical distortions induced by the expansion were measured. The significance of residual stresses is analysed with reference to depth of penetration...report 1978
- document
-
Wanhill, R.J.H. (author)2024-T3, 2048-T851, 7075-T6 and 7475-T761 aluminium alloy sheets were compared for fatigue crack propagation resistance under manoeuvre spectrum and constant amplitude loading. For manoeuvre spectrum loading 7475-T761 was superior overall, and this superiority is most probably due to superior toughness of this alloy. In more detail, 2024-T3 was...report 1978
- document
- Wanhill, R.J.H. (author) report 1977
- document
-
't Hart, W.G.J. (author)Fatigue tests on unidirectional Ca/ep composite material have been performed to investigate whether previous fatigue loading did influence the residual static strength. Residual strength tests were carried out on (0, ± 45)2s and (± 45)2s laminates, while for the (O, ± 45)2s laminate the influence of previous tensile fatigue loading on the...report 1977
- document
-
Schijve, J. (author), Jacobs, F.A. (author), Tromp, P.J. (author)Flight-simulation tests based on a standardized gust load spectrum were carried out in normal air, very dry air and salt water. Specimen thicknesses were t = 2 mm and t = 10 mm, mean stress in flight was 70 or 55 MN/m². In all cases a significant effect of the environment was found. Fatigue lives for t = 10 ram were much shorter than for t = 2...report 1976
- document
-
Schijve, J. (author), Jacobs, F.A. (author), Tromp, P.J. (author)Flight-simulation tests were carried out on sheet specimens notched "by an open hole (Kt = 2.66). The material was 2024-T3 in three conditions; Alclad, bare and chemically milled. The crack initiation period and the crack propagation period were considerably shorter for the Alclad material. The significance of the cladding, both for constant...report 1976
- document
-
Schra, L. (author), van Leeuwen, H.P. (author), Meulman, A.E. (author)The fatigue crack propagation performance of the alloy AZ 74.61 under manoeuvre spectrum loading was studied. The crack propagation behaviour was also compared with that of the American forging alloy AA 7050, not only for simulated manoeuvre loading but also for simulated gust loading and programme loading. It was found that, at comparable...report 1976
- document
-
't Hart, W.G.J. (author), Nederveen, A. (author), Stoffels, E. (author), Tromp, J. (author)Residual strength tests have been performed on 610 mm wide centre cracked panels. During the tests, stable crack growth was filmed and crack opening displacements were measured. Fracture toughness was determined using the method of Feddersen. Flight simulation fatigue tests were carried out to investigate the crack propagation properties. A...report 1975