Offshore wind turbines in shallow coastal waters are typically supported on monopile foundations. Although three-dimensional (3D) finite-element methods are available for the design of monopiles in this context, much of the routine design work is currently conducted using simplified one-dimensional (1D) models based on the p-y method. The p-y method was originally developed for the relatively large embedded length-to-diameter ratio (L/D) piles that are typically employed in offshore oil and gas structures. Concerns exist, however, that this analysis approach may not be appropriate for monopiles with the relatively low values of L/D that are typically adopted for offshore wind turbine structures. This paper describes a new 1D design model for monopile foundations; the model is specifically formulated for offshore wind turbine applications, although the general approach could be adopted for other applications. The model draws on the conventional p-y approach, but extends it to include additional components of soil reaction that act on the pile. The 1D model is calibrated using a set of bespoke 3D finite-element analyses of monopile performance, for pile characteristics and loading conditions that span a predefined design space. The calibrated 1D model provides results that match those obtained from the 3D finite-element calibration analysis, but at a fraction of the computational cost. Moreover, within the calibration space, the 1D model is capable of delivering high-fidelity computations of monopile performance that can be used directly for design purposes. This 1D modelling approach is demonstrated for monopiles installed in a stiff, overconsolidated glacial clay till with a typical North Sea strength and stiffness profile. Although the current form of the model has been developed for homogeneous soil and monotonic loading, it forms a basis from which extensions for soil layering and cyclic loading can be developed. The general approach can be applied to other foundation and soil-structure interaction problems, in which bespoke calibration of a simplified model can lead to more efficient design.@en

This paper describes the results obtained from a field testing campaign on laterally loaded monopiles conducted at Cowden, UK, where the soil consists principally of a heavily overconsolidated glacial till. These tests formed part of the PISA project on the development of improved design methods for monopile foundations for offshore wind turbines. Results obtained for monotonic loading tests on piles of three different diameters (0·273 m, 0·762 m and 2·0 m) are presented. The piles had length-to-diameter ratios (L/D) of between 3 and 10. The tests included the application of monotonic loading incorporating periods of constant load to investigate creep effects, and investigations on the influence of loading rate. Data are presented on measured bending moments and inclinations induced in the piles. Inferred data on lateral displacements of the embedded section of the piles are determined using an optimised structural model. These field data support the development of a new one-dimensional modelling approach for the design of monopile foundations for offshore wind turbines. They also form a unique database of field measurements in an overconsolidated clay, from lateral loading of piles at a vertical distance above the ground surface.@en

The PISA Joint Industry Research Project was concerned with the development of improved design methods for monopile foundations in offshore wind applications. PISA involved large-scale pile tests in overconsolidated glacial till at Cowden, north-east England, and in dense, normally consolidated marine sand at Dunkirk, northern France. This paper describes the experimental set-up for pile testing, with unique features of load-application mechanisms and built-in fibre optic strain gauges. New procedures are described for the interpretation of pile loading data, and specifically for providing precise interpretation of pile displacements.@en

The results obtained from a field testing campaign on laterally loaded monopiles, conducted at a dense sand site in Dunkirk, northern France are described. These tests formed part of the PISA project on the development of improved design methods for monopile foundations for offshore wind turbines. Results obtained from monotonic loading tests on piles of three different diameters (0·273 m, 0·762 m and 2·0 m) are presented. The piles had length-to-diameter ratios (L/D) of between 3 and 10. The tests consisted principally of the application of monotonic loads, incorporating periods of held constant load to investigate creep effects. The influence of loading rate was also investigated. Data are presented on the overall load-displacement behaviour of each of the test piles. Measured data on bending moments and inclinations induced in the piles are also provided. Inferences are made for the displacements in the embedded length of the piles. These field data will support the development of a new one-dimensional modelling approach for the design of monopile foundations for offshore wind turbines. They also form a unique database of field measurements in a dense sand, from lateral loading of piles at a vertical distance above the ground surface.@en