This article provides a detailed analysis of the power electronics solutions enabling bipolar dc grids. The bipolar dc grid concept has proven to be more efficient, flexible, and higher in quality than the conventional unipolar one. However, despite its many features, these systems still have to overcome their issues with asymmetrical loading to avoid voltage imbalances, besides meeting regulatory and safety requirements that are still under development. Advances in power electronics and the large-scale deployment of dc consumer appliances have put this growing architecture in the spotlight, as it has drawn the attention of different research groups recently. The following provides an insightful discussion regarding the topologies that enable these architectures and their regulatory requirements, besides their features and level of development. In addition, some future trends and challenges in the further development of this technology are discussed to motivate future contributions that address open problems and explore new possibilities. @en

DC microgrids initiated the change of a paradigm regarding the concept about electrical distribution networks, especially in the context of the distributed generation associated with renewable energies. However, this new reality opens a new area of research, in which several aspects must be carefully studied. Indeed, the bipolar design is one of the principal dc microgrid configurations considering its characteristic wiring. Although holding many promising advantages, the bipolar dc microgrid has a tendency toward voltage and current imbalances due to the unequal distribution of the loads and generators between the two poles. Thus, specific power electronic-based solutions are required to ensure the balance of these dc microgrids. Within this frame, this article gives a comprehensive review of the multiple architectures and power electronic topologies proposed to mitigate/eliminate this undesired condition. The following provides an insightful classification and discussion with the pros and cons of these solutions. This work can serve as a timely review for researcher/engineers who want to enter the voltage balancing field in the bipolar dc grids and promote the innovation of their power electronics-enabled solutions.@en

DC microgrids can be considered as cyber-physical systems (CPSs) and they are vulnerable to cyberattacks. Therefore, it is highly recommended to have effective plans to detect and remove cyberattacks in dc microgrids. This article shows how artificial neural networks can help to detect and mitigate coordinated false data injection attacks (FDIAs) on current measurements as a type of cyberattacks in dc microgrids. FDIAs try to inject the false data into the system to disrupt the control application, which can make the dc microgrid shutdown. The proposed method to mitigate FDIAs is a decentralized approach and it has the capability to estimate the value of the false injected data. In addition, the proposed strategy can remove the FDIAs even for unfair attacks with high domains on all units at the same time. The proposed method is tested on a detailed simulated dc microgrid using the MATLAB/Simulink environment. Finally, real-time simulations by OPAL-RT on the simulated dc microgrid are implemented to evaluate the proposed strategy. @en

The implementation of finite-control-set model predictive control (FCS-MPC) in voltage source inverters (VSIs) can make the system suffer from poor current harmonics performance, which may complicate the design of the required AC filter. To overcome this shortcoming, a carrier-based modulated model predictive control (CB-MMPC) strategy is proposed in this paper. This method enables the utilization of existing PWM modulation techniques with FCS-MPC, where a modulation waveform with zero-sequence signal injection is generated and compared to a triangular carrier wave, while optimizing the selection of the switching states. As it is shown, the studied CB-MMPC strategy not only considerably improves the current total harmonic distortion (THD) but also attains the performance of fast current dynamic response and robustness as the traditional FCS-MPC. Herein, the detailed implementation of the CB-MMPC control strategy is given, while considering its application to the current feedback control loop of a three-phase three-wire two-level VSI modulated at constant switching frequency. Finally, PLECS circuit simulation and a 3-kW VSI prototype are used to verify the superiority and the effectiveness of the presented CB-MMPC strategy. This is also benchmarked to the FCS-MPC and dead-beat based controllers.@en

The increasing power levels handled by electric vehicle (EV) dc fast chargers will impose additional challenges to the switching devices in order to cope with the efficiency requirements. A cost-effective alternative to achieve highly efficient power conversion is through the partial-power conversion concept. This article validates the advantages of a step-down Type II partial-power converter (PPC), based on the phase-shifted full-bridge converter, for EV fast chargers. By exploiting the reduced voltage range of an EV battery pack along with the reduced power ratio for a Type II PPC, an extremely efficient charging process can be achieved. The concept is validated with the development of a 7-kW demonstrator, and hence, realistic efficiency measurements are obtained. Results indicate the effectiveness of charging a battery by merely handling 13.32% of the power provided to it, with a peak efficiency of 99.11%.@en

This paper explores a novel three-port series-partial-power converter structure to enable electric vehicle (EV) fast chargers. Besides handling a fraction of the power being delivered to the battery, the converter provides both step up and step down of its output voltage, hence being able to interface legacy 400-V as well as state-of-the-art 800-V EVs. Compared to existing partial power converters with both buck and boost capability, the proposed three-port structure is shown to be able to operate over a wider range of operation. Simulation results show the effectivness of the proposed converter, reaching 98.65% maximum efficiency. The proposed topology is finally verified to be an interesting alternative for the dc-dc stages in EV charging stations.@en