The performance of a pilot-scale superoxygenation system was evaluated in clean water and mixed liquor. A mass balance was applied over the pilot-scale system to determine the overall oxygen mass transfer rate coefficient (KLa, h−1), the standard oxygen transfer rate (SOTR, kg O2 d−1), and the standard oxygen transfer efficiency (SOTE, %). Additionally, the alpha factor (α) was determined at a mixed liquor suspend solids (MLSS) concentration of approximately 5 g L−1. SOTEs of nearly 100% were obtained in clean water and mixed liquor. The results showed that at higher oxygen flowrates, higher transfer rates could be achieved; this however, at expenses of the transfer efficiency. As expected, lower transfer efficiencies were observed in mixed liquor compared to clean water. Alpha factors varied between 0.6 and 1.0. However, values of approximately 1.0 can be obtained in all cases by fine tuning the oxygen flowrate delivered to the system.@en

To investigate the influence of high-pressure and shear effects introduced by a concentrated oxygen supply system on the membrane filtration performance, a laboratory-scale membrane bioreactor (MBR) fed artificial municipal wastewater was operated continuously for 80 days in four phases equipped with different aerations systems: (P1) bubble diffusers (days 0–40), (P2) concentrated oxygen supply system, the supersaturated dissolved oxygen (SDOX) (days 41–56), (P3) bubble diffusers (days 57–74), and (P4) SDOX (days 75–80). Various sludge physical-chemical parameters, visual inspection of the membrane, and permeability evaluations were performed. Results showed that the high-pressure effects contributed to fouling of the membranes compared to the bubble diffuser aeration system. Biofouling by microorganisms appeared to be the main contributor to the cake layer when bubble diffusers were used, while fouling by organic matter seemed to be the main contributor to the cake layer when SDOX was used. Small particle size distribution (PSD) (ranging from 1 to 10 and 1–50 μm in size) fractions are a main parameter affecting the intense fouling of membranes (e.g., formation of a dense and thin cake layer). However, PSD alone cannot explain the worsened membrane fouling tendency. Therefore, it can be assumed that a combination of several factors (which certainly includes PSD) led to the severe membrane fouling caused by the high-pressure and shear.@en

Reducing the footprint requirements of membrane bioreactors (MBR)s can both decrease the surface area needs for new wastewater treatment plants (WWTP)s, and increase the treatment capacities of existing WWTPs at a given surface area. In addition, it may promote the development of movable/portable containerized MBRs for a diverse range of wastewater treatment applications. Applications may include the provision of municipal/industrial wastewater treatment in remote areas without sewerage, and the provision of sanitation services under challenging site-specific conditions such as after the occurrence of a human-made or a natural disaster. The reduction of the footprint requirements of MBRs is constrained by the maximum amount of biomass that can be accommodated in the aerobic basin. The biomass concentration is mainly limited by the extremely low oxygen transfer efficiency (OTE) experienced by conventional aeration bubble diffuser systems at mixed liquor total suspended solids (MLSS) concentrations higher than 20 g L-1. Another potential limitation for the operation of MBRs at such high MLSS concentrations is the reduction on the membrane permeability due to excessive fouling. A pilot MBR with a treatment capacity of one m3 d-1 was installed at the research hall facilities at the Harnaschpolder wastewater treatment plant in Delft, The Netherlands. The MBR was operated at MLSS concentrations of up to 28 g L-1 at sludge retention times (SRT)s ranging from 30 to 35 days. The MBR was provided with a Speece cone concentrated oxygen delivery system to overcome the oxygen transfer limitations of conventional bubble diffuser aeration systems at high MLSS concentrations. The MBR performance was evaluated by monitoring the influent and effluent water quality, the membrane permeability, the sludge filterability, the dissolved oxygen (DO) concentration, and the oxygen uptake rate (OUR). The Speece cone proved to be effective in delivering enough oxygen to maintain DO concentrations in the MBR of approximately 2 mg L-1 at MLSS concentrations of up to 22 g L-1. OUR values above 200 mg L-1 h-1 were observed at 14 g L-1 MLSS and higher than 300 mg L-1 h-1 at 22 g L-1 MLSS. The MBR exhibited chemical oxygen demand (COD) removal efficiencies of up to 99% even at a hydraulic retention time (HRT) as low as 3.7 h. A reduction in permeability from 33 to 11 lmh bar-1 was observed when the MLSS concentrations increased from 18.7 to 27.8 g L-1. Sludge filterability values expressed as the added resistance (δR20) fell in the range of "poor filterability" for all the evaluated operational conditions; however, a lower filtration resistance in the range of "moderate filterability" at approximately 23 g L-1 MLSS was noticed. The experimental results suggest that at the evaluated experimental conditions the existent limitations on poor oxygen transfer and low permeability when operating a MBR at high MLSS concentrations can be overcome; therefore, the footprint requirements of MBR systems may be further reduced.@en

The operation of membrane bioreactors (MBRs) at higher than usual mixed liquor suspended solids (MLSS) concentrations may enhance the loading rate treatment capacity while minimizing even further the system’s footprint. This requires operating the MBR at the highest possible MLSS concentration and biomass activity (e.g., at high loading rates and low solid retention times (SRTs)). Both a negative effect of the MLSS concentrations and a positive effect of the SRT on the oxygen transfer have been reported when using conventional fine bubble diffusers. However, most of the evaluations have been carried out either at extremely high SRTs or at low MLSS concentrations eventually underestimating the effects of the MLSS concentration on the oxygen transfer. This research evaluated the current limitations imposed by fine bubble diffusers in the context of the high-loaded MBR (HL-MBR) (i.e., high MLSS and short SRT—the latter emulated by concentrating municipal sludge from a wastewater treatment plant (WWTP) operated at a short SRT of approximately 5 days). The high MLSS concentrations and the short SRT of the original municipal sludge induced a large fraction of mixed liquor volatile suspended solids (MLVSS) in the sludge, promoting a large amount of sludge flocs that eventually accumulated on the surface of the bubbles and reduced the free water content of the suspension. Moreover, the short SRTs at which the original municipal sludge was obtained eventually appear to have promoted the accumulation of surfactants in the sludge mixture. This combination exhibited a detrimental effect on the oxygen transfer. Fine bubble diffusers limit the maximum MLSS concentration for a HL-MBR at 30 g L −1 ; beyond that point is either not technically or not economically feasible to operate; an optimum MLSS concentration of 20 g L −1 is suggested to maximize the treatment capacity while minimizing the system’s footprint. @en

Oxygen transfer in wastewater treatment is significantly influenced by the mixed liquor suspended solids (MLSS). The effect is more pronounced at MLSS concentrations higher than 20 g L−1 when supplying air by conventional diffused aeration systems. The oxygen transfer performance of a supersaturated oxygenation technology (i.e., the supersaturated dissolved oxygen (SDOX) system) was evaluated in clean water and in activated sludge with MLSS concentrations from 4 to 40 g L−1 as a promising technology for uncapping such limitation. The evaluation was carried out at the laboratory facilities of the faculty of food technology and biotechnology at the University of Zagreb. The sludge was collected from a full-scale conventional activated sludge (CAS) wastewater treatment plant (WWTP) operated at a solid retention time (SRT) of approximately 5 days. The evaluation was carried out using a laboratory-scale setup consisting of a bench-scale SDOX system (2.75 L) supplying pure oxygen to a 5 L biological reactor. The SDOX exhibited oxygen mass transfer rate coefficient (KLa) values (2.6 h−1) in clean water lower than for fine bubble diffusers (11 h−1). However, higher oxygen transfer rate (OTR) values and alpha factors (mass transfer ratio of process-water to clean-water) as a function of the MLSS concentration were observed. A standard oxygen transfer efficiency (SOTE) of approximately 100 % in clean water was reported. The SDOX technology can be presented as a promising alternative for supplying dissolved oxygen (DO) into mixed liquor solutions; particularly, at the high MLSS concentrations required by high-loaded membrane bioreactor (HL-MBR) systems and aerobic digesters.@en