As the existing bridge stock is aging, assessment of existing bridges becomes increasingly important. In the Netherlands, the shear capacity of reinforced concrete slab bridges is found to be insufficient. In particular, the shear and punching shear capacity of reinforced concrete slab bridges subjected to concentrated loads from the design tandem or truck is subject to discussion, as the shear behavior is situated in between oneway and two-way shear. Currently, an experimental program is being conducted at Delft University of Technology to determine the shear capacity of straight and skewed reinforced concrete slabs under point loads near to the support. This paper presents the results of the 25 tests conducted on six straight slabs of 5m × 2.5 m × 0.3 m subjected to a proof load testing loading protocol. The failure load and modes of the slabs are described in detail. Reinforced concrete slabs under concentrated loads can fail in shear, punching, and flexure, as well as a combination of these failure modes. The results of the experiments are compared to strength predictions obtained by using current design models and current methods for assessment. These experiments demonstrated that the Dutch guidelines, which are based on previous slab experiments, are an improvement as compared to the Eurocode for the assessment of existing reinforced concrete slab bridges. Ultimately, this work provides recommendations for bridge engineers tasked to assess reinforced concrete skewed slab bridges.

@en

This paper proposes a new mechanical model to describe the dowel action with the aim of using the model to gain a deeper understanding of the unstable dowel splitting cracking observed in shear experiments of beams without shear reinforcement. The model was developed by combining beam on elastic foundation (BEF) theory and fracture mechanics. The proposed model is able to predict the whole evolution process of dowel action until the propagation of the dowel splitting crack becomes unstable. The model theoretically proves that the development of a dowel splitting crack can become unstable under certain conditions, therefore leading to the unstable shear failure of the whole member. In addition to the derivation of the analytical model, the paper also validates the model using data from the literature. Finally, an analytical solution of the critical shear displacement that triggers the unstable dowel splitting crack is derived. It can be used to improve the failure criterion initially proposed in the Critical Shear Displacement Theory (CSDT).

@en

Geopolymer concrete is a new alternative material to conventional concrete with less carbon dioxide emissions. Researchers have reported much research on the material properties of geopolymer concrete. However, research on the behaviour of this newmaterial at the structural level is still limited, especially at a full-scale structural level. Three geopolymer concrete beams with a total height of 700mm were tested till the shear failure. The first two specimens were subjected to the monotonically increasing load until the shear failure. The third specimen was first loaded under sustained load at the level of 80 kN for three weeks to investigate the influence of shrinkage and creep on the cracking behaviour. Then the specimen was then unloaded and reloaded again to failure. Digital Image Correlation (DIC) measurement was used to measure the surface deformation of the whole span of the beam. The crack spacing, crack width and crack development were investigated using the DIC measurement. The experimental results showed that the shear capacity of tested geopolymer concrete beams is lower than the calculated result based on the Eurocode.@en

For reinforced concrete members without shear reinforcement, the shear failure is characterized by the formation of a critical flexural shear crack. Recently experimental observations making use of Digital Image Correlation (DIC) by many researchers suggested the significance of geometric characteristics and kinematic conditions of critical shear cracks in shear failure. However, limited efforts were reported in literature on the quantification of the geometric characteristics of critical shear cracks. This is mainly due to the lack of understanding of the mechanism of how the flexural shear cracks form. In this paper, the available models in literature for the shear crack trajectory and the underlying theoretical assumptions are reviewed first. Those models include the shear crack model proposed by the authors. Next, the shear crack trajectory models are validated using a collection of shear crack patterns based on the DIC data obtained from the shear failure database from Delft University of Technology. The majority of the crack patterns are from full-scale shear tests of deep beams with an effective depth larger than 1.0 m. The comparison helps us to have a basic understanding of how accurate the available flexural shear crack trajectory models can achieve.@en