Epoxy matrix fibre composites have been modified with the addition of rubber and nanosilica particles. Fracture studies conducted on the bulk matrix and composite show a synergistic effect between the nanosilica and rubber, resulting in a 50% increase in bulk fracture energy in an anhydride cured system.@en

An epoxy resin, cured with an anhydride, has been modified by the addition of silica nanoparticles. The particles were introduced via a sol-gel technique which gave a very well dispersed phase of nanosilica particles, which were about 20 nm in diameter, in the thermosetting epoxy polymer matrix. The glass transition temperature of the epoxy polymer was unchanged by the addition of the nanoparticles, but both the modulus and toughness were increased. The fracture energy increased from 77 J/m 2 for the unmodified epoxy to 212 J/m 2 for the epoxy polymer containing 20 wt.% of nanosilica. The fracture surfaces were inspected using scanning electron and atomic force microscopy, and these microscopy studies showed that the silica nanoparticles (a) initiated localised plastic shear-yield deformation bands in the epoxy polymer matrix and (b) debonded and allowed subsequent plastic void-growth of the epoxy polymer matrix. A theoretical model for these toughening micromechanisms has been proposed to confirm that these micromechanisms were indeed responsible for the increased toughness that was observed due to the presence of the silica nanoparticles in the epoxy polymer.@en

The present paper investigates the effect of adding silica nanoparticles to an anhydride-cured epoxy polymer. The formation of 'hybrid' epoxy polymers, containing both silica nanoparticles and carboxyl-Terminated butadiene-Acrylonitrile (CTBNrubber microparticles, is also discussed. The structure/property relationships are considered, with an emphasis on the toughness and the toughening mechanisms. The present work also extends an existing model to predict the toughening effect of the nanoparticles in a thermoset polymer. There was excellent agreement between the predictions and the experimental data for the epoxy containing the silica nanoparticles.@en

The present paper considers the mechanical and fracture properties of four different epoxy polymers containing 0, 10 and 20wt.% of well-dispersed silica nanoparticles. Firstly, it was found that, for any given epoxy polymer, their Young's modulus steadily increased as the volume fraction, vf, of the silica nanoparticles was increased. Modelling studies showed that the measured moduli of the different silica-nanoparticle filled epoxy polymers lay between upper-bound values set by the Halpin-Tsai and the Nielsen 'no-slip' models, and lower-bound values set by the Nielsen 'slip' model; with the last model being the more accurate at relatively high values of vf. Secondly, the presence of silica nanoparticles always led to an increase in the toughness of the epoxy polymer. However, to what extent a given epoxy polymer could be so toughened was related to structure/property relationships which were governed by (a) the values of glass transition temperature, Tg, and molecular weight, Mc, between cross-links of the epoxy polymer, and (b) the adhesion acting at the silica nanoparticle/epoxy-polymer interface. Thirdly, the two toughening mechanisms which were operative in all the epoxy polymers containing silica nanoparticles were identified to be (a) localised shear bands initiated by the stress concentrations around the periphery of the silica nanoparticles, and (b) debonding of the silica nanoparticles followed by subsequent plastic void growth of the epoxy polymer. Finally, the toughening mechanisms have been quantitatively modelled and there was good agreement between the experimentally-measured values and the predicted values of the fracture energy, Gc, for all the epoxy polymers modified by the presence of silica nanoparticles. The modelling studies have emphasised the important roles of the stress versus strain behaviour of the epoxy polymer and the silica nanoparticle/epoxy-polymer interfacial adhesion in influencing the extent of the two toughening mechanisms, and hence the overall fracture energy, Gc, of the nanoparticle-filled polymers.@en

The present paper concentrates on the effect of adding silica nanoparticles to epoxy polymers, which are the basis of modern structural adhesives. The formation of 'hybrid' epoxy polymers, containing both silica nanoparticles and carboxyl-terminated butadiene-acrylonitrile (CTBN) rubber microparticles, is also discussed. The structure/property relationships are considered, with an emphasis on the toughness and the toughening mechanisms.@en

The use of silica nanoparticles and rubbery particles to synthesize hybrid-toughened epoxy polymers has been shown to give a range of novel matrices that can be used to produce composite laminates by a resin infusion under flexible tooling (RITF) process. The glass-fiber-reinforced polymer (GFRP) composite panels were manufactured by RIFT. A thin film of poly(tetrafluoroethylene) (PTFE) was inserted into the fabric prior to resin infusion to act as a starter crack for the fracture specimens. It was observed that the presence of the rubber and nanoparticles does not significantly decrease the flexural modulus or the glass transition temperature of the composite. These formulations exhibit significant increase in the interlaminar fracture energy in both mode I and mode II fracture of GFRP composites.@en

The present paper investigates the effect of adding silica nanoparticles to an anhydride-cured epoxy polymer in bulk and when used as the matrix of carbon- and glass-fibre reinforced composites. The formation of 'hybrid' epoxy polymers, containing both silica nanoparticles and carboxyl-terminated butadiene-acrylonitrile (CTBN) rubber microparticles, is also discussed. The structure/property relationships are considered, with an emphasis on the toughness and the toughening mechanisms. The fracture energy of the bulk epoxy polymer was increased from 77 to 212 J/m2 by the presence of 20 wt% of silica nanoparticles. The observed toughening mechanisms that were operative were (a) plastic shear-yield bands, and (b) debonding of the matrix from the silica nanoparticles, followed by plastic void-growth of the epoxy. The largest increases in toughness observed were for the 'hybrid' materials. Here a maximum fracture energy of 965 J/m2 was measured for a 'hybrid' epoxy polymer containing 9 wt% and 15 wt% of the rubber microparticles and silica nanoparticles, respectively. Most noteworthy was the observation that these increases in the toughness of the bulk polymers were found to be transferred to the fibre composites. Indeed, the interlaminar fracture energies for the fibre-composite materials were increased even further by a fibre-bridging toughening mechanism. The present work also extends an existing model to predict the toughening effect of the nanoparticles in a thermoset polymer. There was excellent agreement between the predictions and the experimental data for the epoxy containing the silica nanoparticles, and for epoxy polymers containing micrometre-sized glass particles. The latter, relatively large, glass particles were investigated to establish whether a 'nano-effect', with respect to increasing the toughness of the epoxy bulk polymers, did indeed exist.@en