Phosphate is a vital nutrient but its presence in surface waters even at very low concentrations can lead to eutrophication. Adsorption is often suggested as a step for reducing phosphate down to very low concentrations. Porous metal oxides can be used as granular adsorbents that have a high surface area and hence a high adsorption capacity. But from a practical point of view, these adsorbents also need to have good adsorption kinetics. The surface area of such adsorbents comes from pores of varying pore size and the pore size distribution (PSD) of the adsorbents can affect the phosphate adsorption kinetics. In this study, the PSD of 4 different adsorbents was correlated with their phosphate adsorption kinetics. The adsorbents based on iron and aluminium (hydr)oxide were grinded and the adsorption performance was studied as a function of their particle size. This was done to identify diffusion limitations due to the PSD of the adsorbents. The phosphate adsorption kinetics were similar for small particles of all the adsorbents. For larger particles, the adsorbents having pores larger than 10 nm (FSP and DD6) showed faster adsorption than adsorbents with smaller pores (GEH and CFH). Even though micropores (pores < 2 nm) contributed to a higher portion of the adsorbent surface area, pores bigger than 10 nm were needed to increase the rate of adsorption.

Eutrophication and the resulting formation of harmful algal blooms (HAB) causes huge economic and environmental damages. Phosphorus (P) from sewage effluent and agricultural run-off has been identified as a major cause for eutrophication. Phosphorous concentrations greater than 100 μg P/L are usually considered high enough to cause eutrophication. The strictest regulations however aim to restrict the concentration below 10 μg P/L. Orthophosphate (or phosphate) is the bioavailable form of phosphorus. Adsorption is often suggested as technology to reduce phosphate to concentrations less than 100 and even 10 μg P/L with the advantages of a low-footprint, minimal waste generation and the option to recover the phosphate. Although many studies report on phosphate adsorption, there is insufficient information regarding parameters that are necessary to evaluate its application on a large scale. This review discusses the main parameters that affect the economics of phosphate adsorption and highlights the research gaps. A scenario and sensitivity analysis shows the importance of adsorbent regeneration and reuse. The cost of phosphate adsorption using reusable porous metal oxide is in the range of $ 100 to 200/Kg P for reducing the phosphate to ultra-low concentrations. Future research needs to focus on adsorption capacity at low phosphate concentrations, regeneration and reuse of both the adsorbent and the regeneration liquid.

Biogenic iron oxides (BioFeO) formed by Leptothrix sp. and Gallionella sp. were compared with chemically formed iron oxides (ChFeO) for their suitability to remove and recover phosphate from solutions. The ChFeO used for comparison included a commercial iron-based adsorbent (GEH) and chemically oxidized iron precipitates from groundwater. Despite contrary observations in earlier studies, the batch experiments showed that BioFeO do not have superior phosphate adsorption capacities compared to ChFeO. However, it seems multiple mechanisms are involved in phosphate removal by BioFeO which make their overall phosphate removal capacity higher than that of ChFeO. The overall phosphate removal capacity of Leptothrix sp. deposits was 26.3 mg P/g d.s., which could be attributed to multiple mechanisms. This included adsorption on the solid phase (6.4 mg P/g d.s.) as well as removal via precipitation and/or adsorption onto suspended complexes released from the BioFeO of Leptothrix sp. (19.6 mg P/g d.s.). Only a very small part of phosphorus (0.3 mg P/g d.s.) was retained in the Leptothrix sp. sheats during bacterial growth. Deposits of Gallionella sp. had an overall phosphate removal capacity of 39.6 mg P/g d.s. Significant amounts of phosphate were apparently incorporated into the Gallionella sp. stalks during their growth (31.0 mg P/g d.s.) and only one-fifth of the total phosphate removal can be related to adsorption (8.6 mg P/g d.s.). Their overall ability to immobilize large quantities of phosphate from solutions indicates that BioFeO could play an important role in environmental and engineered systems for removal of contaminants.

Phosphate is a vital nutrient for life but its discharge from wastewater effluents can lead to eutrophication. Adsorption can be used as effluent polishing step to reduce phosphate to very low concentrations. Adsorbent reusability is an important parameter to make the adsorption process economically feasible. This implies that the adsorbent can be regenerated and used over several cycles without appreciable performance decline. In the current study, we have studied the phosphate adsorption and reusability of commercial iron oxide based adsorbents for wastewater effluent. Effects of adsorbent properties like particle size, surface area, type of iron oxide, and effects of some competing ions were determined. Moreover the effects of regeneration methods, which include an alkaline desorption step and an acid wash step, were studied. It was found that reducing the adsorbent particle size increased the phosphate adsorption of porous adsorbents significantly. Amongst all the other parameters, calcium had the greatest influence on phosphate adsorption and adsorbent reusability. Phosphate adsorption was enhanced by co-adsorption of calcium, but calcium formed surface precipitates such as calcium carbonate. These surface precipitates affected the adsorbent reusability and needed to be removed by implementing an acid wash step. The insights from this study are useful in designing optimal regeneration procedures and improving the lifetime of phosphate adsorbents used for wastewater effluent polishing.

Adsorption is often suggested for to reach very low phosphate levels in municipal wastewater effluent and even to recover phosphate. Adsorbent performance is usually associated with surface area but the exact role of the pore size distribution (PSD) is unclear. Here, we show the effect of the PSD on phosphate adsorption. Granular activated carbons (GACs) with varying PSDs were treated with potassium permanganate followed by reaction with ferric chloride to form iron oxide coated GACs (Fe-GACs). Energy dispersive X-ray and kinetics experiments confirmed that manganese anchored on the GAC is important for subsequent iron attachment. Mössbauer spectroscopy showed presence of ferrihydrite in Fe-GAC. Transmission electron microscopy showed that the iron oxide particles are not present in the micropores of the GACs. Phosphate adsorption isotherms were performed with the Fe-GACs and adsorption at lower phosphate concentrations correlated with the porous area of &#x003E;3 nm of the adsorbents, a high fraction of which is contributed by mesopores. These results show that high surface areas of GACs resulting from micropores do not contribute to adsorption at low phosphate concentrations. This can be explained by the micropores being difficult to coat with iron oxide nanoparticles, but in addition the diffusion of phosphate into these pores could also be hindered. It is therefore recommended to use backbones having high mesoporous areas. This information is useful for developing adsorbents particularly for applications treating low phosphate concentrations, for e.g. in municipal wastewater effluent polishing.