This work explores a spatial printing method to fabricate continuous fiber-reinforced thermoplastic composites (CFRTPCs), which can achieve exceptional mechanical performance. For models giving complex 3D stress distribution under loads, typical planar-layer based fiber placement usually fails to provide sufficient reinforcement due to their orientations being constrained to planes. The effectiveness of fiber reinforcement could be maximized by using multi-axis additive manufacturing (MAAM) to better control the orientation of continuous fibers in 3D-printed composites. Here, we propose a computational approach to generate 3D toolpaths that satisfy two major reinforcement objectives: (1) following the maximal stress directions in critical regions and (2) connecting multiple load-bearing regions by continuous fibers. Principal stress lines are first extracted in an input solid model to identify critical regions. Curved layers aligned with maximal stresses in these critical regions are generated by computing an optimized scalar field and extracting its iso-surfaces. Then, topological analysis and operations are applied to each curved layer to generate a computational domain that preserves fiber continuity between load-bearing regions. Lastly, continuous fiber toolpaths aligned with maximal stresses are generated on each surface layer by computing an optimized scalar field and extracting its iso-curves. A hardware system with dual robotic arms is employed to conduct the physical MAAM tasks depositing polymer or fiber reinforced polymer composite materials by applying a force normal to the extrusion plane to aid consolidation. When comparing to planar-layer based printing results in tension, up to 644% failure load and 240% stiffness are observed on shapes fabricated by our spatial printing method. We demonstrate the versatility of our approach through various complex load cases which demonstrate their successful implementation of continuous fiber printing in 3D.@en

Poor H 2 O 2 -resistance by enzymes is a key bottleneck in the epoxidation process of oil by enzymatic methods. In this study, the stability of three lipases, from Aspergillus oryzae lipase (AOL), Aspergillus fumigatus lipase B (AflB), and marine Janibacter (MAJ1), in the presence of H 2 O 2 was evaluated in different types of natural deep eutectic solvents (NADES). This stability was strengthened significantly in the NADES compared to the buffer. Specifically, AOL retained 84.7% of its initial activity in the presence of choline chloride/sorbitol (1:1 M ratio) and 3 mol L −1 H 2 O 2 after 24 h incubation at 40°C. In addition, the two-phase epoxidation process was optimized with AOL in ChCl/sorbitol to reach up to 96.8% conversion under the optimized conditions (molar ratio of octanoic acid/H 2 O 2 /C=C-bonds = 0.3:1.5:1, enzyme loading of 15 U g −1 of soybean oil, ChCl/sorbitol content of 70.0% of the weight of hydrophilic phase, and reaction temperature of 50°C). Moreover, the lipase dispersed in NADES retained approximately 66% of its initial activity after being used for seven batch cycles. Overall, NADES-based enzymatic epoxidation is a feasible and promising strategy for the synthesis of epoxidized oils. @en

The anisotropy of mechanical strength on a 3D printed model can be controlled in a multi-axis 3D printing system as materials can be accumulated along dynamically varied directions. In this paper, we present a new computational framework to generate specially designed layers and toolpaths of multi-axis 3D printing for strengthening a model by aligning filaments along the directions with large stresses. The major challenge comes from how to effectively decompose a solid into a sequence of strength-aware and collision-free working surfaces. We formulate it as a problem to compute an optimized governing field together with a selected orientation of fabrication setup. Iso-surfaces of the governing field are extracted as working surface layers for filament alignment. Supporting structures in curved layers are constructed by extrapolating the governing field to enable the fabrication of overhangs. Compared with planar-layer based Fused Deposition Modeling (FDM) technology, models fabricated by our method can withstand up to 6.35× loads in experimental tests. @en

Multi-axis additive manufacturing enables high flexibility of material deposition along dynamically varied directions. The Cartesian motion platforms of these machines include three parallel axes and two rotational axes. Singularity on rotational axes is a critical issue to be tackled in motion planning for ensuring high quality of manufacturing results. The highly nonlinear mapping in the singular region can convert a smooth toolpath with uniformly sampled waypoints defined in the model coordinate system into a highly discontinuous motion in the machine coordinate system, which leads to over-extrusion/under-extrusion of materials in filament-based additive manufacturing. The problem is challenging as both the maximal and the minimal speeds at the tip of a printer head must be controlled in motion. Moreover, collision may occur when sampling-based collision avoidance is employed. In this letter, we present a motion planning method to support the manufacturing realization of designed toolpaths for multi-axis additive manufacturing. Problems of singularity and collision are considered in an integrated manner to improve the motion therefore the quality of fabrication. @en